Modern exynos SoCs such as Exynos Auto v9 have different internal clock
divider, for example "4". To support this internal value, this adds
clk_div of the s3c64xx_spi_port_config and assign "2" as the default
value to existing s3c64xx_spi_port_config.
Signed-off-by: Chanho Park <chanho61.park@xxxxxxxxxxx>
---
drivers/spi/spi-s3c64xx.c | 28 ++++++++++++++++++++--------
1 file changed, 20 insertions(+), 8 deletions(-)
diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c
index 0c917cf891ca..ff565e57736b 100644
--- a/drivers/spi/spi-s3c64xx.c
+++ b/drivers/spi/spi-s3c64xx.c
@@ -131,6 +131,7 @@ struct s3c64xx_spi_dma_data {
* @fifo_lvl_mask: Bit-mask for {TX|RX}_FIFO_LVL bits in SPI_STATUS register.
* @rx_lvl_offset: Bit offset of RX_FIFO_LVL bits in SPI_STATUS regiter.
* @tx_st_done: Bit offset of TX_DONE bit in SPI_STATUS regiter.
+ * @clk_div: Internal clock divider
* @quirks: Bitmask of known quirks
* @high_speed: True, if the controller supports HIGH_SPEED_EN bit.
* @clk_from_cmu: True, if the controller does not include a clock mux and
@@ -148,6 +149,7 @@ struct s3c64xx_spi_port_config {
int rx_lvl_offset;
int tx_st_done;
int quirks;
+ int clk_div;
bool high_speed;
bool clk_from_cmu;
bool clk_ioclk;
@@ -620,6 +622,7 @@ static int s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd)
void __iomem *regs = sdd->regs;
int ret;
u32 val;
+ int div = sdd->port_conf->clk_div;
/* Disable Clock */
if (!sdd->port_conf->clk_from_cmu) {
@@ -668,16 +671,15 @@ static int s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd)
writel(val, regs + S3C64XX_SPI_MODE_CFG);
if (sdd->port_conf->clk_from_cmu) {
- /* The src_clk clock is divided internally by 2 */
- ret = clk_set_rate(sdd->src_clk, sdd->cur_speed * 2);
+ ret = clk_set_rate(sdd->src_clk, sdd->cur_speed * div);
if (ret)
return ret;
- sdd->cur_speed = clk_get_rate(sdd->src_clk) / 2;
+ sdd->cur_speed = clk_get_rate(sdd->src_clk) / div;
} else {
/* Configure Clock */
val = readl(regs + S3C64XX_SPI_CLK_CFG);
val &= ~S3C64XX_SPI_PSR_MASK;
- val |= ((clk_get_rate(sdd->src_clk) / sdd->cur_speed / 2 - 1)
+ val |= ((clk_get_rate(sdd->src_clk) / sdd->cur_speed / div - 1)
& S3C64XX_SPI_PSR_MASK);
writel(val, regs + S3C64XX_SPI_CLK_CFG);
@@ -871,6 +873,7 @@ static int s3c64xx_spi_setup(struct spi_device *spi)
struct s3c64xx_spi_csinfo *cs = spi->controller_data;
struct s3c64xx_spi_driver_data *sdd;
int err;
+ int div;
sdd = spi_master_get_devdata(spi->master);
if (spi->dev.of_node) {
@@ -889,22 +892,24 @@ static int s3c64xx_spi_setup(struct spi_device *spi)
pm_runtime_get_sync(&sdd->pdev->dev);
+ div = sdd->port_conf->clk_div;
+
/* Check if we can provide the requested rate */
if (!sdd->port_conf->clk_from_cmu) {
u32 psr, speed;
/* Max possible */
- speed = clk_get_rate(sdd->src_clk) / 2 / (0 + 1);
+ speed = clk_get_rate(sdd->src_clk) / div / (0 + 1);
if (spi->max_speed_hz > speed)
spi->max_speed_hz = speed;
- psr = clk_get_rate(sdd->src_clk) / 2 / spi->max_speed_hz - 1;
+ psr = clk_get_rate(sdd->src_clk) / div / spi->max_speed_hz - 1;
psr &= S3C64XX_SPI_PSR_MASK;
if (psr == S3C64XX_SPI_PSR_MASK)
psr--;
- speed = clk_get_rate(sdd->src_clk) / 2 / (psr + 1);
+ speed = clk_get_rate(sdd->src_clk) / div / (psr + 1);
if (spi->max_speed_hz < speed) {
if (psr+1 < S3C64XX_SPI_PSR_MASK) {
psr++;
@@ -914,7 +919,7 @@ static int s3c64xx_spi_setup(struct spi_device *spi)
}
}
- speed = clk_get_rate(sdd->src_clk) / 2 / (psr + 1);
+ speed = clk_get_rate(sdd->src_clk) / div / (psr + 1);
if (spi->max_speed_hz >= speed) {
spi->max_speed_hz = speed;
} else {
@@ -1396,6 +1401,7 @@ static const struct s3c64xx_spi_port_config s3c2443_spi_port_config = {
.fifo_lvl_mask = { 0x7f },
.rx_lvl_offset = 13,
.tx_st_done = 21,
+ .clk_div = 2,
.high_speed = true,
};
@@ -1403,12 +1409,14 @@ static const struct s3c64xx_spi_port_config s3c6410_spi_port_config = {
.fifo_lvl_mask = { 0x7f, 0x7F },
.rx_lvl_offset = 13,
.tx_st_done = 21,
+ .clk_div = 2,
};
static const struct s3c64xx_spi_port_config s5pv210_spi_port_config = {
.fifo_lvl_mask = { 0x1ff, 0x7F },
.rx_lvl_offset = 15,
.tx_st_done = 25,
+ .clk_div = 2,
.high_speed = true,
};
@@ -1416,6 +1424,7 @@ static const struct s3c64xx_spi_port_config exynos4_spi_port_config = {
.fifo_lvl_mask = { 0x1ff, 0x7F, 0x7F },
.rx_lvl_offset = 15,
.tx_st_done = 25,
+ .clk_div = 2,
.high_speed = true,
.clk_from_cmu = true,
.quirks = S3C64XX_SPI_QUIRK_CS_AUTO,
@@ -1425,6 +1434,7 @@ static const struct s3c64xx_spi_port_config exynos7_spi_port_config = {
.fifo_lvl_mask = { 0x1ff, 0x7F, 0x7F, 0x7F, 0x7F, 0x1ff},
.rx_lvl_offset = 15,
.tx_st_done = 25,
+ .clk_div = 2,
.high_speed = true,
.clk_from_cmu = true,
.quirks = S3C64XX_SPI_QUIRK_CS_AUTO,
@@ -1434,6 +1444,7 @@ static const struct s3c64xx_spi_port_config exynos5433_spi_port_config = {
.fifo_lvl_mask = { 0x1ff, 0x7f, 0x7f, 0x7f, 0x7f, 0x1ff},
.rx_lvl_offset = 15,
.tx_st_done = 25,
+ .clk_div = 2,
.high_speed = true,
.clk_from_cmu = true,
.clk_ioclk = true,
@@ -1444,6 +1455,7 @@ static const struct s3c64xx_spi_port_config fsd_spi_port_config = {
.fifo_lvl_mask = { 0x7f, 0x7f, 0x7f, 0x7f, 0x7f},
.rx_lvl_offset = 15,
.tx_st_done = 25,
+ .clk_div = 2,
.high_speed = true,
.clk_from_cmu = true,
.clk_ioclk = false,
--
2.36.1
