Florian Vaussard <florian.vaussard@xxxxxxx> writes:
> Hello Kevin,
>
> On 06/01/2013 12:45 AM, Kevin Hilman wrote:
>> On most OMAP3 platforms, the twl4030 IRQ line is connected to the
>> SYS_NIRQ line on OMAP. Therefore, configure the defaults for the
>> SYS_NIRQ pin in the twl4030 DTS file.
>>
>> Boards that hook up the twl4030 differently can easily override this
>> in their board-specific DTS file.
>>
>> This allows RTC wake from off-mode to work again on OMAP3-based
>> platforms with twl4030. Tested on 3530/Beagle, 3730/Beagle-xM,
>> 3530/Overo, 3730/Overo-STORM.
>>
>> Signed-off-by: Kevin Hilman <khilman@xxxxxxxxxx>
>> ---
>> arch/arm/boot/dts/twl4030.dtsi | 17 +++++++++++++++++
>> 1 file changed, 17 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/twl4030.dtsi b/arch/arm/boot/dts/twl4030.dtsi
>> index b3034da..c7fe9f6 100644
>> --- a/arch/arm/boot/dts/twl4030.dtsi
>> +++ b/arch/arm/boot/dts/twl4030.dtsi
>> @@ -13,6 +13,8 @@
>> compatible = "ti,twl4030";
>> interrupt-controller;
>> #interrupt-cells = <1>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&twl4030_pins>;
>>
>> rtc {
>> compatible = "ti,twl4030-rtc";
>> @@ -92,3 +94,18 @@
>> #pwm-cells = <2>;
>> };
>> };
>> +
>> +&omap3_pmx_core {
>
> Here you are making the TWL4030 to explicitly depend on OMAP3. Could
> this chip be used by another target? If the case, I would put this
> piece of code in the files including twl4030. Otherwise it's ok here.
I talked this over with Tony before posting. In theorry, it could be
used on other platforms. In practice, it's only used on OMAP. We can
easily move this to board files if needed later, but thought it would be
simpler to put it here. I'll let Benoit decide.
>> + /*
>> + * On most OMAP3 platforms, the twl4030 IRQ line is connected
>> + * to the SYS_NIRQ line on OMAP. Therefore, configure the
>> + * defaults for the SYS_NIRQ pin here. Boards that hook up
>> + * the twl4030 differently can easily override this in their
>> + * board-specific DTS file.
>> + */
>> + twl4030_pins: pinmux_twl4030_pins {
>> + pinctrl-single,pins = <
>> + 0x1b0 0x4118 /* sys_nirq.sys_nirq WAKEUP | INPUT_PULLUP | MODE 0 */
>
> By using pinctrl constants:
>
> 0x1b0 (PIN_INPUT_PULLUP | WAKEUP_EN | MUX_MODE0) /* sys_nirq.sys_nirq */
Yup.
>> + >;
>> + };
>> +};
>>
>
> I will test this afternoon on an Overo.
Thanks,
Kevin
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
