* Tony Lindgren <tony@xxxxxxxxxxx> [160111 12:27]:
>
> OK so the issue is that the twl msecure pin should be high to enable
> the RTC registers. We used to have that code with platform_data, but
> no longer have it with device tree based booting. I'll send a patch
> for that.
>
> Curiously setting jumper j5 on beagle-x15 that controls what used to
> be the msecure and now is powerhold, does the opposite.. The
> device boots automatically but RTC is stopped?
And here's a fix the issue for omap5. Beagle-x15 needs to be
investigated more.
Care to test it with your RTC enabling patch?
Regards,
Tony
8< ---------------
From: Tony Lindgren <tony@xxxxxxxxxxx>
Date: Mon, 11 Jan 2016 14:35:24 -0800
Subject: [PATCH] ARM: dts: Fix omap5 PMIC control lines for RTC writes
The palmas PMIC has some control lines that need to be muxed properly
for things to work. The sys_nirq pin is used for interrupts, and msecure
pin is used for enabling writes to some PMIC registers.
Without these pins configured properly things can fail in mysterious
ways. For example, we can't update the RTC registers on palmas PMIC
unless the msecure pin is configured. And this is probably the reason
why we had RTC missing from the omap5 dts file.
According to "OMAP5430 ES2.0 Data Manual [Public] VErsion A (Rev. F)"
swps052f.pdf, mux mode 1 is for sys_drm_msecure so there's no need to
configure it as a GPIO pin.
Signed-off-by: Tony Lindgren <tony@xxxxxxxxxxx>
--- a/arch/arm/boot/dts/omap5-board-common.dtsi
+++ b/arch/arm/boot/dts/omap5-board-common.dtsi
@@ -213,6 +213,12 @@
>;
};
+ palmas_msecure_pins: palmas_msecure_pins {
+ pinctrl-single,pins = <
+ OMAP5_IOPAD(0x180, PIN_OUTPUT | MUX_MODE1) /* gpio8_234.sys_drm_msecure */
+ >;
+ };
+
usbhost_pins: pinmux_usbhost_pins {
pinctrl-single,pins = <
0x84 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */
@@ -278,6 +284,12 @@
&usbhost_wkup_pins
>;
+ palmas_sys_nirq_pins: pinmux_palmas_sys_nirq_pins {
+ pinctrl-single,pins = <
+ OMAP5_IOPAD(0x068, PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq1 */
+ >;
+ };
+
usbhost_wkup_pins: pinmux_usbhost_wkup_pins {
pinctrl-single,pins = <
0x1A (PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */
@@ -345,6 +357,8 @@
interrupt-controller;
#interrupt-cells = <2>;
ti,system-power-controller;
+ pinctrl-names = "default";
+ pinctrl-0 = <&palmas_sys_nirq_pins &palmas_msecure_pins>;
extcon_usb3: palmas_usb {
compatible = "ti,palmas-usb-vid";
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
