Hi, Sinse a couple of months I'm trying to get my second DVB-C card to work, but with no luck. I have searched a lot around and even tried the last media_build. I am running linux 3.5.0-26-generic with the latests media_build from here (http://git.linuxtv.org/media_build.git) For some reason the card won't get a lock. Here are my test results: Terratec Cinergy PCIe Dual dvbv5-scan -a2 -v channel2.conf using demux '/dev/dvb/adapter2/demux0' Device DRXK DVB-C DVB-T (/dev/dvb/adapter2/frontend0) capabilities: CAN_FEC_1_2 CAN_FEC_2_3 CAN_FEC_3_4 CAN_FEC_5_6 CAN_FEC_7_8 CAN_FEC_AUTO CAN_GUARD_INTERVAL_AUTO CAN_HIERARCHY_AUTO CAN_INVERSION_AUTO CAN_MUTE_TS CAN_QAM_16 CAN_QAM_32 CAN_QAM_64 CAN_QAM_128 CAN_QAM_256 CAN_RECOVER CAN_TRANSMISSION_MODE_AUTO DVB API Version 5.6, Current v5 delivery system: DVBC/ANNEX_A Supported delivery systems: [DVBC/ANNEX_A] DVBC/ANNEX_C DVBT Scanning frequency #1 304000000 FREQUENCY = 304000000 MODULATION = QAM/64 INVERSION = AUTO SYMBOL_RATE = 6875000 INNER_FEC = AUTO DELIVERY_SYSTEM = DVBC/ANNEX_A status 00 | signal 0% | snr 0% | ber 0 | unc 119 | tune failed dmesg [ 5.332360] cx23885_dvb_register() allocating 1 frontend(s) [ 5.332365] cx23885[0]: cx23885 based dvb card [ 5.365162] drxk: status = 0x639160d9 [ 5.365167] drxk: detected a drx-3916k, spin A3, xtal 20.250 MHz [ 5.465869] DRXK driver version 0.9.4300 [ 5.504139] drxk: frontend initialized. [ 5.517782] mt2063_attach: Attaching MT2063 [ 5.517788] DVB: registering new adapter (cx23885[0]) [ 5.517791] DVB: registering adapter 1 frontend 0 (DRXK DVB-T)... [ 5.518664] cx23885_dvb_register() allocating 1 frontend(s) [ 5.518668] cx23885[0]: cx23885 based dvb card [ 5.533886] drxk: status = 0x639130d9 [ 5.533896] drxk: detected a drx-3913k, spin A3, xtal 20.250 MHz [ 5.617338] DRXK driver version 0.9.4300 [ 5.650861] drxk: frontend initialized. [ 5.650872] mt2063_attach: Attaching MT2063 [ 5.650876] DVB: registering new adapter (cx23885[0]) [ 5.650878] DVB: registering adapter 2 frontend 0 (DRXK DVB-C DVB-T)... [ 5.651338] cx23885_dev_checkrevision() Hardware revision = 0xa5 [ 5.651343] cx23885[0]/0: found at 0000:02:00.0, rev: 4, irq: 16, latency: 0, mmio: 0xff400000 ........ [ 153.727978] mt2063: detected a mt2063 B3 [ 153.877050] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params: [ 153.877058] drxk: 02 00 00 00 10 00 05 00 03 02 .......... [ 156.989702] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params: [ 156.989710] drxk: 02 00 00 00 10 00 05 00 03 02 .......... [ 170.558420] mt2063: detected a mt2063 B3 [ 170.629422] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params: [ 170.629430] drxk: 02 00 00 00 10 00 05 00 03 02 .......... [ 173.742057] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params: [ 173.742065] drxk: 02 00 00 00 10 00 05 00 03 02 .......... [ 251.314900] mt2063: detected a mt2063 B3 [ 251.385932] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params: [ 251.385940] drxk: 02 00 00 00 10 00 05 00 03 02 .......... [ 254.498522] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params: [ 254.498530] drxk: 02 00 00 00 10 00 05 00 03 02 .......... lspci -vvv 02:00.0 Multimedia video controller: Conexant Systems, Inc. CX23885 PCI Video and Audio Decoder (rev 04) Subsystem: TERRATEC Electronic GmbH Cinergy T PCIe Dual Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at ff400000 (64-bit, non-prefetchable) [size=2M] Capabilities: [40] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <2us, L1 <4us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [90] Vital Product Data Product Name: " End Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn- Capabilities: [200 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed+ WRR32+ WRR64+ WRR128- Ctrl: ArbSelect=WRR64 Status: InProgress- Port Arbitration Table [240] <?> VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01 Status: NegoPending- InProgress- Kernel driver in use: cx23885 Kernel modules: cx23885 It says no signal, but if I put the antenna-cable in my other DVB-C card and do a scan I get: Philips TV-Card dvbv5-scan -a0 -v channel2.conf using demux '/dev/dvb/adapter0/demux0' Device Philips TDA10023 DVB-C (/dev/dvb/adapter0/frontend0) capabilities: CAN_FEC_AUTO CAN_INVERSION_AUTO CAN_QAM_16 CAN_QAM_32 CAN_QAM_64 CAN_QAM_128 CAN_QAM_256 CAN_QPSK DVB API Version 5.6, Current v5 delivery system: DVBC/ANNEX_A Supported delivery systems: [DVBC/ANNEX_A] DVBC/ANNEX_C Scanning frequency #1 304000000 FREQUENCY = 304000000 MODULATION = QAM/64 INVERSION = AUTO SYMBOL_RATE = 6875000 INNER_FEC = AUTO DELIVERY_SYSTEM = DVBC/ANNEX_A status 1f | signal 97% | snr 94% | ber 1728 | unc 62194 | FE_HAS_LOCK Service #0 (101) Nederland 1 channel 0.1.0 Service #1 (102) Nederland 2 channel 0.2.1 Service #2 (103) Nederland 3 channel 0.3.2 Service #3 (8101) 100%NL channel 0.801.3 Service #4 (8102) Arrow Classic Rock channel 0.802.4 Service #5 (8103) Arrow Jazz channel 0.803.5 Service #6 (8104) BBC radio 1 channel 0.804.6 Service #7 (8105) BBC radio 2 channel 0.805.7 Service #8 (8106) BBC radio 3 channel 0.806.8 Service #9 (8107) BBC radio 4 channel 0.807.9 Service #10 (8108) BNR channel 0.808.10 Service #11 (8109) Classic FM channel 0.809.11 New transponder/channel found: #2: 505937920 New transponder/channel found: #3: 515112960 New transponder/channel found: #4: 524288000 New transponder/channel found: #5: 529530880 New transponder/channel found: #6: 538705920 New transponder/channel found: #7: 547880960 New transponder/channel found: #8: 557056000 New transponder/channel found: #9: 566231040 New transponder/channel found: #10: 312000000 New transponder/channel found: #11: 320000000 New transponder/channel found: #12: 328000000 New transponder/channel found: #13: 336000000 New transponder/channel found: #14: 580648960 New transponder/channel found: #15: 344000000 New transponder/channel found: #16: 352000000 New transponder/channel found: #17: 360000000 New transponder/channel found: #18: 368000000 Does anyone know what I'm doing wrong? Thanks, Jan Saris -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
