On 07-04-13 12:56, Jan Saris wrote:
Hi,
Sinse a couple of months I'm trying to get my second DVB-C card to
work, but with no luck.
I have searched a lot around and even tried the last media_build.
I have the same card and while I don't see anything wrong (you have 2
dvb-t devices installed right? adapter0 is something else, and the
Cinergy is adapter1 and adapter2? Ah, yes you do say 'other dvb-c' sorry.
I am running linux 3.5.0-26-generic with the latests media_build from
here (http://git.linuxtv.org/media_build.git)
For some reason the card won't get a lock. Here are my test results:
Remember to set the frontend properly; dvb-fe-tool from memory (tab
completion ftw). And remember the cinergy is dual dvb-t; but only single
dvb-c (and single analog, but i think that is still not implemented?)
Terratec Cinergy PCIe Dual
dvbv5-scan -a2 -v channel2.conf
using demux '/dev/dvb/adapter2/demux0'
Device DRXK DVB-C DVB-T (/dev/dvb/adapter2/frontend0) capabilities:
CAN_FEC_1_2 CAN_FEC_2_3 CAN_FEC_3_4 CAN_FEC_5_6 CAN_FEC_7_8
CAN_FEC_AUTO CAN_GUARD_INTERVAL_AUTO CAN_HIERARCHY_AUTO
CAN_INVERSION_AUTO CAN_MUTE_TS CAN_QAM_16 CAN_QAM_32 CAN_QAM_64
CAN_QAM_128 CAN_QAM_256 CAN_RECOVER CAN_TRANSMISSION_MODE_AUTO
DVB API Version 5.6, Current v5 delivery system: DVBC/ANNEX_A
Supported delivery systems: [DVBC/ANNEX_A] DVBC/ANNEX_C DVBT
Scanning frequency #1 304000000
FREQUENCY = 304000000
MODULATION = QAM/64
INVERSION = AUTO
SYMBOL_RATE = 6875000
INNER_FEC = AUTO
DELIVERY_SYSTEM = DVBC/ANNEX_A
status 00 | signal 0% | snr 0% | ber 0 | unc 119 | tune failed
dmesg
[ 5.332360] cx23885_dvb_register() allocating 1 frontend(s)
[ 5.332365] cx23885[0]: cx23885 based dvb card
[ 5.365162] drxk: status = 0x639160d9
[ 5.365167] drxk: detected a drx-3916k, spin A3, xtal 20.250 MHz
[ 5.465869] DRXK driver version 0.9.4300
[ 5.504139] drxk: frontend initialized.
[ 5.517782] mt2063_attach: Attaching MT2063
[ 5.517788] DVB: registering new adapter (cx23885[0])
[ 5.517791] DVB: registering adapter 1 frontend 0 (DRXK DVB-T)...
[ 5.518664] cx23885_dvb_register() allocating 1 frontend(s)
[ 5.518668] cx23885[0]: cx23885 based dvb card
[ 5.533886] drxk: status = 0x639130d9
[ 5.533896] drxk: detected a drx-3913k, spin A3, xtal 20.250 MHz
[ 5.617338] DRXK driver version 0.9.4300
[ 5.650861] drxk: frontend initialized.
[ 5.650872] mt2063_attach: Attaching MT2063
[ 5.650876] DVB: registering new adapter (cx23885[0])
[ 5.650878] DVB: registering adapter 2 frontend 0 (DRXK DVB-C DVB-T)...
[ 5.651338] cx23885_dev_checkrevision() Hardware revision = 0xa5
[ 5.651343] cx23885[0]/0: found at 0000:02:00.0, rev: 4, irq: 16,
latency: 0, mmio: 0xff400000
........
[ 153.727978] mt2063: detected a mt2063 B3
[ 153.877050] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
[ 153.877058] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
[ 156.989702] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
[ 156.989710] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
[ 170.558420] mt2063: detected a mt2063 B3
[ 170.629422] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
[ 170.629430] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
[ 173.742057] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
[ 173.742065] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
[ 251.314900] mt2063: detected a mt2063 B3
[ 251.385932] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
[ 251.385940] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
[ 254.498522] drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
[ 254.498530] drxk: 02 00 00 00 10 00 05 00 03 02 ..........
lspci -vvv
02:00.0 Multimedia video controller: Conexant Systems, Inc. CX23885
PCI Video and Audio Decoder (rev 04)
Subsystem: TERRATEC Electronic GmbH Cinergy T PCIe Dual
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ff400000 (64-bit, non-prefetchable) [size=2M]
Capabilities: [40] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
Latency L0 <2us, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Vital Product Data
Product Name: "
End
Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt-
UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [200 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32+ WRR64+ WRR128-
Ctrl: ArbSelect=WRR64
Status: InProgress-
Port Arbitration Table [240] <?>
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
Kernel driver in use: cx23885
Kernel modules: cx23885
It says no signal, but if I put the antenna-cable in my other DVB-C
card and do a scan I get:
Philips TV-Card
dvbv5-scan -a0 -v channel2.conf
using demux '/dev/dvb/adapter0/demux0'
Device Philips TDA10023 DVB-C (/dev/dvb/adapter0/frontend0) capabilities:
CAN_FEC_AUTO CAN_INVERSION_AUTO CAN_QAM_16 CAN_QAM_32
CAN_QAM_64 CAN_QAM_128 CAN_QAM_256 CAN_QPSK
DVB API Version 5.6, Current v5 delivery system: DVBC/ANNEX_A
Supported delivery systems: [DVBC/ANNEX_A] DVBC/ANNEX_C
Scanning frequency #1 304000000
FREQUENCY = 304000000
MODULATION = QAM/64
INVERSION = AUTO
SYMBOL_RATE = 6875000
INNER_FEC = AUTO
DELIVERY_SYSTEM = DVBC/ANNEX_A
status 1f | signal 97% | snr 94% | ber 1728 | unc 62194 | FE_HAS_LOCK
Service #0 (101) Nederland 1 channel 0.1.0
Service #1 (102) Nederland 2 channel 0.2.1
Service #2 (103) Nederland 3 channel 0.3.2
Service #3 (8101) 100%NL channel 0.801.3
Service #4 (8102) Arrow Classic Rock channel 0.802.4
Service #5 (8103) Arrow Jazz channel 0.803.5
Service #6 (8104) BBC radio 1 channel 0.804.6
Service #7 (8105) BBC radio 2 channel 0.805.7
Service #8 (8106) BBC radio 3 channel 0.806.8
Service #9 (8107) BBC radio 4 channel 0.807.9
Service #10 (8108) BNR channel 0.808.10
Service #11 (8109) Classic FM channel 0.809.11
New transponder/channel found: #2: 505937920
New transponder/channel found: #3: 515112960
New transponder/channel found: #4: 524288000
New transponder/channel found: #5: 529530880
New transponder/channel found: #6: 538705920
New transponder/channel found: #7: 547880960
New transponder/channel found: #8: 557056000
New transponder/channel found: #9: 566231040
New transponder/channel found: #10: 312000000
New transponder/channel found: #11: 320000000
New transponder/channel found: #12: 328000000
New transponder/channel found: #13: 336000000
New transponder/channel found: #14: 580648960
New transponder/channel found: #15: 344000000
New transponder/channel found: #16: 352000000
New transponder/channel found: #17: 360000000
New transponder/channel found: #18: 368000000
Does anyone know what I'm doing wrong?
Thanks,
Jan Saris
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
