On 12/04/14 00:24, Srinivas Pandruvada wrote:
On 03/29/2014 03:49 AM, Jonathan Cameron wrote:
On 19/03/14 16:56, Srinivas Pandruvada wrote:
This chip has two modes to control secondary sensor attached to it.
One is master mode and another is bypass mode. In master mode
MPU6500 will directly communicates to the secondary sensor device
attached to it. This can support very few secondary devices in this
mode.
But when configured in bypass mode the i2c lines are directly connected
to host i2c bus controller.
Since in master mode it can only support few devices and they are not
implemented in this driver, set the default mode to bypass mode.
When some multiplexer is implemented to use MPU6050 master mode,
this mode can be enabled when requested.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@xxxxxxxxxxxxxxx>
To my understanding this still doesn't deal with the fact that devices
on the slave bus are not connected if this driver is not loaded or has
gone to sleep. Hence this needs as previously discussed to be done as
a single input, single output i2c mux. That way the kernel 'knows'
there is something inbetween that needs to be in the correct state.
I am looking at a way to implement multiplexing 1:1 as suggested in email chains.
The problem I have:
My two slave devices (MPU6XXX and AK8963 enumerated via ACPI. So they i2clients are already tied to the I2C adapter.
So the ACPI has no description of the fact that the ak8963 is connected through the
MPU device. That's irritating.
We don't have a board setup file in PC like platform.
I have implemented in mux in MPU6XXX driver. But AK8963 driver is not
aware about mux adapter, it will not call my mux select function. So
I feel that we need to have a board setup file, to correctly create
i2C clients attaching to correct adapter for using this design. Is
this correct?
It ought to be possible to do it from ACPI enumeration but
only if there is some representation of the topology from ACPI.
Otherwise we will need to represent this weirdness somewhere...
Thanks,
Srinivas
Jonathan
---
drivers/iio/imu/inv_mpu6050/inv_mpu_core.c | 19 ++++++++++++++++++-
drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h | 4 ++++
2 files changed, 22 insertions(+), 1 deletion(-)
diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
index 52d688b..744eba4 100644
--- a/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
+++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
@@ -53,6 +53,7 @@ static const struct inv_mpu6050_reg_map reg_set_6050 = {
.int_enable = INV_MPU6050_REG_INT_ENABLE,
.pwr_mgmt_1 = INV_MPU6050_REG_PWR_MGMT_1,
.pwr_mgmt_2 = INV_MPU6050_REG_PWR_MGMT_2,
+ .int_pin_cfg = INV_MPU6050_REG_INT_PIN_CFG,
};
static const struct inv_mpu6050_chip_config chip_config_6050 = {
@@ -608,6 +609,20 @@ static const struct iio_info mpu_info = {
.validate_trigger = inv_mpu6050_validate_trigger,
};
+static int inv_set_bypass_status(struct inv_mpu6050_state *st, bool enable)
+{
+ int ret;
+
+ if (enable)
+ ret = inv_mpu6050_write_reg(st, st->reg->int_pin_cfg,
+ st->client->irq |
+ INV_MPU6050_BIT_BYPASS_EN);
+ else
+ ret = inv_mpu6050_write_reg(st, st->reg->int_pin_cfg,
+ st->client->irq);
+ return ret;
+}
+
/**
* inv_check_and_setup_chip() - check and setup chip.
*/
@@ -646,7 +661,9 @@ static int inv_check_and_setup_chip(struct inv_mpu6050_state *st,
if (result)
return result;
- return 0;
+ result = inv_set_bypass_status(st, true);
+
+ return result;
}
/**
diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h b/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h
index 4ddfd03..591ac2e 100644
--- a/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h
+++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h
@@ -54,6 +54,7 @@ struct inv_mpu6050_reg_map {
u8 int_enable;
u8 pwr_mgmt_1;
u8 pwr_mgmt_2;
+ u8 int_pin_cfg;
};
/*device enum */
@@ -186,6 +187,9 @@ struct inv_mpu6050_state {
#define INV_MPU6050_MIN_FIFO_RATE 4
#define INV_MPU6050_ONE_K_HZ 1000
+#define INV_MPU6050_REG_INT_PIN_CFG 0x37
+#define INV_MPU6050_BIT_BYPASS_EN 0x2
+
/* scan element definition */
enum inv_mpu6050_scan {
INV_MPU6050_SCAN_ACCL_X,
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-iio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
