Hi, Some time ago, I returned my hard disk and got a new one. Lately, I'm having performance issues again and I suspect there is a hardware error again like last time. If you could confirm this I would be most grateful. Thanks in advance! # smartctl -a /dev/sdb smartctl 5.41 2011-03-16 r3296 [x86_64-unknown-linux-gnu-2.6.38-2-amd64] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: ST2000DL003-9VT166 Serial Number: 5YD1YD5P Firmware Version: CC32 User Capacity: 2,000,398,934,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Sat Apr 30 12:59:32 2011 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 623) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x30b7) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 096 082 006 Pre-fail Always - 2447656 3 Spin_Up_Time 0x0003 097 092 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 265 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 060 060 030 Pre-fail Always - 1108085 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 717 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 74 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 792 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 065 062 045 Old_age Always - 35 (Min/Max 35/35) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 202 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 265 194 Temperature_Celsius 0x0022 035 040 000 Old_age Always - 35 (0 19 0 0) 195 Hardware_ECC_Recovered 0x001a 015 009 000 Old_age Always - 2447656 197 Current_Pending_Sector 0x0012 096 096 000 Old_age Always - 368 198 Offline_Uncorrectable 0x0010 096 096 000 Old_age Offline - 368 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 9354438771404 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 793142133 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 307847059 SMART Error Log Version: 1 ATA Error Count: 828 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 828 occurred at disk power-on lifetime: 705 hours (29 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 ff ff ff ef 00 03:44:18.432 READ DMA EXT 27 00 00 00 00 00 e0 00 03:44:18.431 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 03:44:18.423 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 03:44:18.391 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 00 03:44:18.391 READ NATIVE MAX ADDRESS EXT Error 827 occurred at disk power-on lifetime: 705 hours (29 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 ff ff ff ef 00 03:44:15.060 READ DMA EXT 27 00 00 00 00 00 e0 00 03:44:15.059 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 03:44:15.051 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 03:44:15.019 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 00 03:44:15.019 READ NATIVE MAX ADDRESS EXT Error 826 occurred at disk power-on lifetime: 705 hours (29 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 ff ff ff ef 00 03:44:11.687 READ DMA EXT 27 00 00 00 00 00 e0 00 03:44:11.686 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 03:44:11.662 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 03:44:11.566 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 00 03:44:11.566 READ NATIVE MAX ADDRESS EXT Error 825 occurred at disk power-on lifetime: 705 hours (29 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 ff ff ff ef 00 03:44:08.323 READ DMA EXT 27 00 00 00 00 00 e0 00 03:44:08.322 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 03:44:08.314 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 03:44:08.282 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 00 03:44:08.282 READ NATIVE MAX ADDRESS EXT Error 824 occurred at disk power-on lifetime: 705 hours (29 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 ff ff ff ef 00 03:44:04.950 READ DMA EXT 27 00 00 00 00 00 e0 00 03:44:04.949 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 03:44:04.941 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 03:44:04.910 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 00 03:44:04.909 READ NATIVE MAX ADDRESS EXT SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. On Tue, Jan 25, 2011 at 7:06 AM, BU66ER BAD6ER <debu66er@xxxxxxxxx> wrote: > Dear both, > > Thanks for the input! I will return this hard disk as soon as possible. > > Here below is the latest output. > > Best regards! > > # smartctl -a /dev/sdb > smartctl 5.40 2010-07-12 r3124 [x86_64-unknown-linux-gnu] (local build) > Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net > > === START OF INFORMATION SECTION === > Model Family: Seagate Barracuda LP > Device Model: ST32000542AS > Serial Number: 5XW20H7P > Firmware Version: CC34 > User Capacity: 2,000,398,934,016 bytes > Device is: In smartctl database [for details use: -P show] > ATA Version is: 8 > ATA Standard is: ATA-8-ACS revision 4 > Local Time is: Tue Jan 25 06:57:27 2011 CET > SMART support is: Available - device has SMART capability. > SMART support is: Enabled > > === START OF READ SMART DATA SECTION === > SMART overall-health self-assessment test result: PASSED > > General SMART Values: > Offline data collection status: (0x00) Offline data collection activity > was never started. > Auto Offline Data Collection: Disabled. > Self-test execution status: ( 0) The previous self-test routine completed > without error or no self-test has ever > been run. > Total time to complete Offline > data collection: ( 633) seconds. > Offline data collection > capabilities: (0x73) SMART execute Offline immediate. > Auto Offline data collection > on/off support. > Suspend Offline collection upon new > command. > No Offline surface scan supported. > Self-test supported. > Conveyance Self-test supported. > Selective Self-test supported. > SMART capabilities: (0x0003) Saves SMART data before entering > power-saving mode. > Supports SMART auto save timer. > Error logging capability: (0x01) Error logging supported. > General Purpose Logging supported. > Short self-test routine > recommended polling time: ( 1) minutes. > Extended self-test routine > recommended polling time: ( 255) minutes. > Conveyance self-test routine > recommended polling time: ( 2) minutes. > SCT capabilities: (0x103f) SCT Status supported. > SCT Error Recovery Control supported. > SCT Feature Control supported. > SCT Data Table supported. > > SMART Attributes Data Structure revision number: 10 > Vendor Specific SMART Attributes with Thresholds: > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE > UPDATED WHEN_FAILED RAW_VALUE > 1 Raw_Read_Error_Rate 0x000f 096 085 006 Pre-fail > Always - 166323635 > 3 Spin_Up_Time 0x0003 100 100 000 Pre-fail > Always - 0 > 4 Start_Stop_Count 0x0032 099 099 020 Old_age > Always - 1164 > 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail > Always - 0 > 7 Seek_Error_Rate 0x000f 100 253 030 Pre-fail > Always - 499927 > 9 Power_On_Hours 0x0032 100 100 000 Old_age > Always - 334 > 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail > Always - 0 > 12 Power_Cycle_Count 0x0032 099 099 020 Old_age > Always - 1190 > 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age > Always - 0 > 184 End-to-End_Error 0x0032 100 100 099 Old_age > Always - 0 > 187 Reported_Uncorrect 0x0032 001 001 000 Old_age > Always - 495 > 188 Command_Timeout 0x0032 100 099 000 Old_age > Always - 4295032833 > 189 High_Fly_Writes 0x003a 100 100 000 Old_age > Always - 0 > 190 Airflow_Temperature_Cel 0x0022 081 063 045 Old_age > Always - 19 (Lifetime Min/Max 19/19) > 194 Temperature_Celsius 0x0022 019 040 000 Old_age > Always - 19 (0 16 0 0) > 195 Hardware_ECC_Recovered 0x001a 048 033 000 Old_age > Always - 166323635 > 197 Current_Pending_Sector 0x0012 100 099 000 Old_age > Always - 24 > 198 Offline_Uncorrectable 0x0010 100 099 000 Old_age > Offline - 24 > 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age > Always - 0 > 240 Head_Flying_Hours 0x0000 100 253 000 Old_age > Offline - 65979287602589 > 241 Total_LBAs_Written 0x0000 100 253 000 Old_age > Offline - 1931349171 > 242 Total_LBAs_Read 0x0000 100 253 000 Old_age > Offline - 2326768434 > > SMART Error Log Version: 1 > ATA Error Count: 573 (device log contains only the most recent five errors) > CR = Command Register [HEX] > FR = Features Register [HEX] > SC = Sector Count Register [HEX] > SN = Sector Number Register [HEX] > CL = Cylinder Low Register [HEX] > CH = Cylinder High Register [HEX] > DH = Device/Head Register [HEX] > DC = Device Command Register [HEX] > ER = Error register [HEX] > ST = Status register [HEX] > Powered_Up_Time is measured from power on, and printed as > DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, > SS=sec, and sss=millisec. It "wraps" after 49.710 days. > > Error 573 occurred at disk power-on lifetime: 317 hours (13 days + 5 hours) > When the command that caused the error occurred, the device was > active or idle. > > After command completion occurred, registers were: > ER ST SC SN CL CH DH > -- -- -- -- -- -- -- > 40 51 00 83 74 1b 07 Error: UNC at LBA = 0x071b7483 = 119239811 > > Commands leading to the command that caused the error were: > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name > -- -- -- -- -- -- -- -- ---------------- -------------------- > c8 00 08 7f 74 1b e7 00 13:20:31.001 READ DMA > 27 00 00 00 00 00 e0 00 13:20:31.000 READ NATIVE MAX ADDRESS EXT > ec 00 00 00 00 00 a0 00 13:20:30.992 IDENTIFY DEVICE > ef 03 46 00 00 00 a0 00 13:20:30.986 SET FEATURES [Set transfer mode] > 27 00 00 00 00 00 e0 00 13:20:30.964 READ NATIVE MAX ADDRESS EXT > > Error 572 occurred at disk power-on lifetime: 317 hours (13 days + 5 hours) > When the command that caused the error occurred, the device was > active or idle. > > After command completion occurred, registers were: > ER ST SC SN CL CH DH > -- -- -- -- -- -- -- > 40 51 00 83 74 1b 07 Error: UNC at LBA = 0x071b7483 = 119239811 > > Commands leading to the command that caused the error were: > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name > -- -- -- -- -- -- -- -- ---------------- -------------------- > c8 00 08 7f 74 1b e7 00 13:20:27.236 READ DMA > 27 00 00 00 00 00 e0 00 13:20:27.235 READ NATIVE MAX ADDRESS EXT > ec 00 00 00 00 00 a0 00 13:20:27.227 IDENTIFY DEVICE > ef 03 46 00 00 00 a0 00 13:20:27.223 SET FEATURES [Set transfer mode] > 27 00 00 00 00 00 e0 00 13:20:27.199 READ NATIVE MAX ADDRESS EXT > > Error 571 occurred at disk power-on lifetime: 317 hours (13 days + 5 hours) > When the command that caused the error occurred, the device was > active or idle. > > After command completion occurred, registers were: > ER ST SC SN CL CH DH > -- -- -- -- -- -- -- > 40 51 00 83 74 1b 07 Error: UNC at LBA = 0x071b7483 = 119239811 > > Commands leading to the command that caused the error were: > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name > -- -- -- -- -- -- -- -- ---------------- -------------------- > c8 00 08 7f 74 1b e7 00 13:20:23.451 READ DMA > 27 00 00 00 00 00 e0 00 13:20:23.451 READ NATIVE MAX ADDRESS EXT > ec 00 00 00 00 00 a0 00 13:20:23.442 IDENTIFY DEVICE > ef 03 46 00 00 00 a0 00 13:20:23.438 SET FEATURES [Set transfer mode] > 27 00 00 00 00 00 e0 00 13:20:23.407 READ NATIVE MAX ADDRESS EXT > > Error 570 occurred at disk power-on lifetime: 317 hours (13 days + 5 hours) > When the command that caused the error occurred, the device was > active or idle. > > After command completion occurred, registers were: > ER ST SC SN CL CH DH > -- -- -- -- -- -- -- > 40 51 00 83 74 1b 07 Error: UNC at LBA = 0x071b7483 = 119239811 > > Commands leading to the command that caused the error were: > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name > -- -- -- -- -- -- -- -- ---------------- -------------------- > c8 00 08 7f 74 1b e7 00 13:20:19.659 READ DMA > 27 00 00 00 00 00 e0 00 13:20:19.658 READ NATIVE MAX ADDRESS EXT > ec 00 00 00 00 00 a0 00 13:20:19.650 IDENTIFY DEVICE > ef 03 46 00 00 00 a0 00 13:20:19.619 SET FEATURES [Set transfer mode] > 27 00 00 00 00 00 e0 00 13:20:19.534 READ NATIVE MAX ADDRESS EXT > > Error 569 occurred at disk power-on lifetime: 317 hours (13 days + 5 hours) > When the command that caused the error occurred, the device was > active or idle. > > After command completion occurred, registers were: > ER ST SC SN CL CH DH > -- -- -- -- -- -- -- > 40 51 00 83 74 1b 07 Error: UNC at LBA = 0x071b7483 = 119239811 > > Commands leading to the command that caused the error were: > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name > -- -- -- -- -- -- -- -- ---------------- -------------------- > c8 00 08 7f 74 1b e7 00 13:20:15.894 READ DMA > 27 00 00 00 00 00 e0 00 13:20:15.893 READ NATIVE MAX ADDRESS EXT > ec 00 00 00 00 00 a0 00 13:20:15.885 IDENTIFY DEVICE > ef 03 46 00 00 00 a0 00 13:20:15.880 SET FEATURES [Set transfer mode] > 27 00 00 00 00 00 e0 00 13:20:15.857 READ NATIVE MAX ADDRESS EXT > > SMART Self-test log structure revision number 1 > No self-tests have been logged. [To run self-tests, use: smartctl -t] > > > SMART Selective self-test log data structure revision number 1 > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS > 1 0 0 Not_testing > 2 0 0 Not_testing > 3 0 0 Not_testing > 4 0 0 Not_testing > 5 0 0 Not_testing > Selective self-test flags (0x0): > After scanning selected spans, do NOT read-scan remainder of disk. > If Selective self-test is pending on power-up, resume after 0 minute delay. > > On Tue, Jan 25, 2011 at 2:21 AM, Robert Hancock <hancockrwd@xxxxxxxxx> wrote: >> On 01/23/2011 05:05 AM, BU66ER BAD6ER wrote: >>> >>> Hi, >>> >>> Four weeks ago I bought a new 2TB Seagate Barracuda internal SATA >>> drive. That drive has two 667GB ext4 partions (667GB unused) and it is >>> used for storage. My main system (Debian Sid 64-bit and KDE) resides >>> on a 40GB SSD, also using ext4. >>> >>> Two weeks ago I noticed a severe performance drop, where any file >>> manager couldn't view directories on the 2TB disk without a one or two >>> minute penalty. After that I have had three hard freezes of that disk >>> and the entire system. Before the freeze there is very much hd >>> activity and finally I need to turn the power off. I have now also >>> made a backup of /dev/sdb1 should it be fatally serious. >>> >>> I was recommended by someone at the #debian irc to make changes to the >>> spindown_time but that only helped for a few days. Yesterday, the 3rd >>> freeze came and the system wouldn't even recognize the disk after >>> reboot; just 'clicking' waiting for a response. I showed the kern.log >>> to someone at the same channel who concluded that this should be a >>> firmware issue. >>> >>> Here is the latest kern.log which may identify the issue: I hope it >>> contains the relevant details. But first the output of smartctl -a >>> /dev/sdb. >>> >>> I have now set the hdparm spindown_time to 0, disabling disk sleep >>> which seems to have been the culprit as judged on messages in the >>> Dolphin file manager etc. >>> >>> Thanks for any help! >>> >>> >>>> # smartctl -a /dev/sdb >>>> smartctl 5.40 2010-07-12 r3124 [x86_64-unknown-linux-gnu] (local build) >>>> Copyright (C) 2002-10 by Bruce Allen, >>>> http://smartmontools.sourceforge.net >>>> >>>> === START OF INFORMATION SECTION === >>>> Model Family: Seagate Barracuda LP >>>> Device Model: ST32000542AS >>>> Serial Number: 5XW20H7P >>>> Firmware Version: CC34 >>>> User Capacity: 2,000,398,934,016 bytes >>>> Device is: In smartctl database [for details use: -P show] >>>> ATA Version is: 8 >>>> ATA Standard is: ATA-8-ACS revision 4 >>>> Local Time is: Sun Jan 23 11:50:56 2011 CET >>>> SMART support is: Available - device has SMART capability. >>>> SMART support is: Enabled >>>> >>>> === START OF READ SMART DATA SECTION === >>>> SMART overall-health self-assessment test result: PASSED >>>> >>>> General SMART Values: >>>> Offline data collection status: (0x00) Offline data collection activity >>>> was never started. >>>> Auto Offline Data Collection: >>>> Disabled. >>>> Self-test execution status: ( 0) The previous self-test routine >>>> completed >>>> without error or no self-test has >>>> ever >>>> been run. >>>> Total time to complete Offline >>>> data collection: ( 633) seconds. >>>> Offline data collection >>>> capabilities: (0x73) SMART execute Offline immediate. >>>> Auto Offline data collection >>>> on/off support. >>>> Suspend Offline collection upon >>>> new >>>> command. >>>> No Offline surface scan >>>> supported. >>>> Self-test supported. >>>> Conveyance Self-test supported. >>>> Selective Self-test supported. >>>> SMART capabilities: (0x0003) Saves SMART data before entering >>>> power-saving mode. >>>> Supports SMART auto save timer. >>>> Error logging capability: (0x01) Error logging supported. >>>> General Purpose Logging >>>> supported. >>>> Short self-test routine >>>> recommended polling time: ( 1) minutes. >>>> Extended self-test routine >>>> recommended polling time: ( 255) minutes. >>>> Conveyance self-test routine >>>> recommended polling time: ( 2) minutes. >>>> SCT capabilities: (0x103f) SCT Status supported. >>>> SCT Error Recovery Control >>>> supported. >>>> SCT Feature Control supported. >>>> SCT Data Table supported. >>>> >>>> SMART Attributes Data Structure revision number: 10 >>>> Vendor Specific SMART Attributes with Thresholds: >>>> ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED >>>> WHEN_FAILED RAW_VALUE >>>> 1 Raw_Read_Error_Rate 0x000f 100 089 006 Pre-fail Always >>>> - 184733939 >>>> 3 Spin_Up_Time 0x0003 100 100 000 Pre-fail Always >>>> - 0 >>>> 4 Start_Stop_Count 0x0032 099 099 020 Old_age Always >>>> - 1160 >>>> 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always >>>> - 0 >>>> 7 Seek_Error_Rate 0x000f 100 253 030 Pre-fail Always >>>> - 296094 >>>> 9 Power_On_Hours 0x0032 100 100 000 Old_age Always >>>> - 307 >>>> 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always >>>> - 0 >>>> 12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always >>>> - 1186 >>>> 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always >>>> - 0 >>>> 184 End-to-End_Error 0x0032 100 100 099 Old_age Always >>>> - 0 >>>> 187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always >>>> - 225 >>>> 188 Command_Timeout 0x0032 100 099 000 Old_age Always >>>> - 4295032833 >>>> 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always >>>> - 0 >>>> 190 Airflow_Temperature_Cel 0x0022 063 063 045 Old_age Always >>>> - 37 (Lifetime Min/Max 19/37) >>>> 194 Temperature_Celsius 0x0022 037 040 000 Old_age Always >>>> - 37 (0 16 0 0) >>>> 195 Hardware_ECC_Recovered 0x001a 052 033 000 Old_age Always >>>> - 184733939 >>>> 197 Current_Pending_Sector 0x0012 100 099 000 Old_age Always >>>> - 40 >>>> 198 Offline_Uncorrectable 0x0010 100 099 000 Old_age Offline >>>> - 40 >>>> 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always >>>> - 0 >>>> 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline >>>> - 210019605808507 >>>> 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline >>>> - 546635184 >>>> 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline >>>> - 2195715347 >> >> The SMART data shows there haven't been many start/stops other than from >> power cycles, so I don't think spindown is related here. The error log >> entries and the Offline_Uncorrectable and Reported_Uncorrect attributes >> would indicate that your drive is having read errors. Think you likely need >> a new drive. >> > -- To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
