Mikael Pettersson wrote:
Robert Hancock writes:
> On 12/27/2009 02:37 PM, thomas schorpp wrote:
> > LG GH22NS40 NL01 (possibly Renesas chipset)
> > VIA8237 SATA (produces basically same errors), Promise SATA II 150 20579
> > HBAs.
> >
> > Linux 2.6.32.2
> > hal polling
> > devkit polling
> > wodim
> > growisofs
> >
> > port_status 0x20280000 (Data Transfer Overrun Error & Target Device Fault)?
> >
> > Looks like a hardware combination incompatibility.
> > Most applicable ATA_HORKAGES in sourcecode already tried.
> >
> > Not found the sense code yet since FEATURE specific according to
> > T13/1410D revision 3b.
> >
> > Comments?
> >
> > y
> > tom
> >
> > dmesg |grep -A 10 ata
> >
> > sata_promise 0000:00:0d.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
> > scsi5 : sata_promise
> > scsi6 : sata_promise
> > scsi7 : sata_promise
> > ata6: SATA max UDMA/133 mmio m4096@0xfbefe000 ata 0xfbefe200 irq 17
> > ata7: SATA max UDMA/133 mmio m4096@0xfbefe000 ata 0xfbefe280 irq 17
> > ata8: PATA max UDMA/133 mmio m4096@0xfbefe000 ata 0xfbefe300 irq 17
> > ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> > ata6.00: ATAPI: HL-DT-ST DVDRAM GH22NS40, NL01, max UDMA/100
> > ata6.00: configured for UDMA/100
> > scsi 5:0:0:0: CD-ROM HL-DT-ST DVDRAM GH22NS40 NL01 PQ: 0 ANSI: 5
> > sr0: scsi3-mmc drive: 125x/125x writer dvd-ram cd/rw xa/form2 cdda tray
> > sr 5:0:0:0: Attached scsi CD-ROM sr0
> > sr 5:0:0:0: Attached scsi generic sg2 type 5
> > ata7: SATA link down (SStatus 0 SControl 300)
> > ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
> > ata6.00: port_status 0x20280000
> > sr 5:0:0:0: [sr0] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 40 00
> > ata6.00: cmd a0/01:00:00:00:fc/00:00:00:00:00/a0 tag 0 dma 131072 in
> > res 51/54:03:00:00:fc/00:00:00:00:00/e0 Emask 0x2 (HSM violation)
> > ata6.00: status: { DRDY ERR }
> > ata6: hard resetting link
> > ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> > ata6.00: configured for UDMA/100
> > ata6: EH complete
> > ...
> > <period, ~10 times in series>
> > ...
> > ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
> > ata6.00: port_status 0x20280000
> > sr 5:0:0:0: [sr0] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 02 00
> > ata6.00: cmd a0/01:00:00:00:10/00:00:00:00:00/a0 tag 0 dma 4096 in
> > res 51/54:03:00:00:10/00:00:00:00:00/e0 Emask 0x2 (HSM violation)
> > ata6.00: status: { DRDY ERR }
> > ata6: hard resetting link
> > ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> > ata6.00: configured for UDMA/100
> > ata6: EH complete
> > ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
> > ata6.00: port_status 0x20280000
> > sr 5:0:0:0: [sr0] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 02 00
> > ata6.00: cmd a0/01:00:00:00:10/00:00:00:00:00/a0 tag 0 dma 4096 in
> > res 51/54:03:00:00:10/00:00:00:00:00/e0 Emask 0x2 (HSM violation)
> > ata6.00: status: { DRDY ERR }
> > ata6: hard resetting link
> > ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> > ata6.00: configured for UDMA/100
> > ata6: EH complete
> > ata6.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
> > ata6.00: port_status 0x20280000
> > sr 5:0:0:0: [sr0] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 02 00
> > ata6.00: cmd a0/01:00:00:00:10/00:00:00:00:00/a0 tag 0 dma 4096 in
> > res 51/54:03:00:00:10/00:00:00:00:00/e0 Emask 0x2 (HSM violation)
> > ata6.00: status: { DRDY ERR }
> > ata6: hard resetting link
> > ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> > ata6.00: configured for UDMA/100
> > sr 5:0:0:0: [sr0] Result: hostbyte=0x00 driverbyte=0x08
> > sr 5:0:0:0: [sr0] Sense Key : 0x5 [current] Info fld=0x0
> > sr 5:0:0:0: [sr0] ASC=0x21 ASCQ=0x0
> > sr 5:0:0:0: [sr0] CDB: cdb[0]=0x28: 28 00 00 00 00 00 00 00 02 00
>
> Well, it's a READ command, and the response is "LOGICAL BLOCK ADDRESS
> OUT OF RANGE". Seems reasonable if it's a blank disc in the drive (is it?)
>
> According to the code comments in sata_promise, "overrun error" means
> the S/G byte count was larger than the drive requires. Which I suppose
> would happen here, because the drive didn't actually transfer any data.
> sata_promise raises an HSM error on that though which triggers resets
> and such. Seems like an overreaction, for ATAPI commands anyway, as that
> can happen normally. CCing Mikael.
Thanks for the report. I'll try to come up with a patch to reduce
the severity of overruns to something less than HSM.
> What were the errors you were seeing on the VIA controller?
I'd like to see that too.
No such HSM error messages or any EH invocation with the sata-via on 2.6.32.2 :-)
Nor on growisofs startup or dvdrw drive servo failure like it occured with sata-promise.
Hot-swapped drives:
...
ata2: link is slow to respond, please be patient (ready=0)
ata2: soft resetting link
ata2: link is slow to respond, please be patient (ready=0)
ata2: SRST failed (errno=-16)
ata2: soft resetting link
ata2: link is slow to respond, please be patient (ready=0)
ata3: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0xe frozen
ata3: hotplug_status 0x1
ata3: SError: { 10B8B Dispar }
ata3: hard resetting link
ata2: SRST failed (errno=-16)
ata2: soft resetting link
ata3: SATA link down (SStatus 0 SControl 300)
ata2: link is slow to respond, please be patient (ready=0)
ata3: hard resetting link
ata3: SATA link down (SStatus 0 SControl 300)
ata3: limiting SATA link speed to 1.5 Gbps
ata3: hard resetting link
ata3: SATA link down (SStatus 0 SControl 310)
ata3.00: disabled
ata3: EH complete
ata3.00: detaching (SCSI 2:0:0:0)
ata2.00: class mismatch 1 != 3
ata2.00: revalidation failed (errno=-19)
ata2: soft resetting link
ata2.00: class mismatch 1 != 3
ata2.00: revalidation failed (errno=-19)
ata2.00: disabled
ata2: soft resetting link
ata2.00: ATAPI: HL-DT-ST DVDRAM GH22NS40, NL01, max UDMA/100
ata2.00: configured for UDMA/100
ata2: EH complete
ata2.00: detaching (SCSI 1:0:0:0)
sd 1:0:0:0: [sdb] Synchronizing SCSI cache
sd 1:0:0:0: [sdb] Stopping disk
scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GH22NS40 NL01 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 125x/125x writer dvd-ram cd/rw xa/form2 cdda tray
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr 1:0:0:0: Attached scsi generic sg1 type 5
...
--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html