On Dienstag, 18. März 2008, Tejun Heo wrote: > Hello, > > Volker Armin Hemmann wrote: > > I tried some more stuff, replaced the cables, played with bios settings. > > > > No change. > > > > Then I updated to 2.6.24.3 - and no hangs or 'softreset' failures > > anymore. > > I don't see any libata changes which can cause such difference. Weird. > Is this result reliably reproducible? it was for a little bit more than 24h. I booted and rebooted several times to make sure - and everything was fine, but after a good night and on the Xth boot, the hang occured again - and since then it is there. Reliable on every boot :( (and the softreset failed message on reboots). Of course, I booted and rebooted several times. And it stays. Maybe it is the hardware. But I replaced the cables already and smart says the disk is ok. SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA _of_first_error # 1 Short offline Completed without error 00% 8124 - # 2 Short offline Completed without error 00% 8067 - # 3 Short offline Completed without error 00% 3402 - # 4 Extended offline Completed without error 00% 3374 - <snip> > > > 2.6.24.2 and 2.6.24.3 both have the reiser4 patch added. > > > > So > > 2.6.24.2 = bad > > 2.6.24.3 = good it only was good for a couple of boots. > > 2.6.25-rc5 = bad > > > > Setting AHCI in bios still results in timeouts and harddisks not found. > > Does pci=nomsi help? oh yes! It does. I changed the 'Sata operation mode' setting from 'non raid' to AHCI, booted with that option: [ 35.026629] Driver 'sd' needs updating - please use bus_type methods [ 35.026702] ahci 0000:00:0a.0: version 3.0 [ 35.026877] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23 [ 35.026922] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LSA0] -> GSI 23 (level, low) -> IRQ 23 [ 36.029726] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode [ 36.029777] ahci 0000:00:0a.0: flags: 64bit sntf led clo pmp pio [ 36.029817] PCI: Setting latency timer of device 0000:00:0a.0 to 64 [ 36.030019] scsi0 : ahci [ 36.030114] scsi1 : ahci [ 36.030180] scsi2 : ahci [ 36.030245] scsi3 : ahci [ 36.030333] ata1: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc100 irq 23 [ 36.030381] ata2: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc180 irq 23 [ 36.030428] ata3: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc200 irq 23 [ 36.030476] ata4: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc280 irq 23 [ 36.659406] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 36.660019] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133 [ 36.660062] ata1.00: 312581808 sectors, multi 16: LBA48 [ 36.660680] ata1.00: configured for UDMA/133 [ 37.291368] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 37.311928] ata2.00: ATA-8: SAMSUNG HD501LJ, CR100-12, max UDMA7 [ 37.311968] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 37.313968] ata2.00: configured for UDMA/133 [ 37.630631] ata3: SATA link down (SStatus 0 SControl 300) [ 37.949937] ata4: SATA link down (SStatus 0 SControl 300) [ 37.950026] scsi 0:0:0:0: Direct-Access ATA WDC WD1600JS-00M 10.0 PQ: 0 ANSI: 5 [ 37.950136] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) [ 37.950181] sd 0:0:0:0: [sda] Write Protect is off [ 37.950219] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 37.950227] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 37.950297] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) [ 37.950340] sd 0:0:0:0: [sda] Write Protect is off [ 37.950378] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 37.950385] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 37.950434] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [ 37.984324] sd 0:0:0:0: [sda] Attached SCSI disk [ 37.984459] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10 PQ: 0 ANSI: 5 [ 37.984568] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [ 37.984612] sd 1:0:0:0: [sdb] Write Protect is off [ 37.984650] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 37.984659] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 37.984729] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [ 37.984772] sd 1:0:0:0: [sdb] Write Protect is off [ 37.984810] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 37.984817] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 37.984866] sdb: sdb1 sdb2 [ 37.994164] sd 1:0:0:0: [sdb] Attached SCSI disk the most obvious change are the different interrupts: 23 instead of 315 (non-raid, without nosmi) or 218 (systemrescuecd 1.0, ahci setting, without nosmi) full dmesg is attached. Thanks for looking into this mess. Glück Auf, Volker
[ 0.000000] Linux version 2.6.24.3reiser4 (root@energy) (gcc version 4.2.3 (Gentoo 4.2.3 p1.0)) #1 SMP Sun Mar 16 20:32:58 CET 2008 [ 0.000000] Command line: root=/dev/sda3 nmi_watchdog=0 console=tty6 pci=nomsi [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000cffb0000 (usable) [ 0.000000] BIOS-e820: 00000000cffb0000 - 00000000cffc0000 (ACPI data) [ 0.000000] BIOS-e820: 00000000cffc0000 - 00000000cfff0000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000cfff0000 - 00000000d0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved) [ 0.000000] BIOS-e820: 00000000ff380000 - 0000000100000000 (reserved) [ 0.000000] BIOS-e820: 0000000100000000 - 0000000130000000 (usable) [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used [ 0.000000] Entering add_active_range(0, 256, 851888) 1 entries of 256 used [ 0.000000] Entering add_active_range(0, 1048576, 1245184) 2 entries of 256 used [ 0.000000] end_pfn_map = 1245184 [ 0.000000] DMI present. [ 0.000000] ACPI: RSDP 000F98E0, 0014 (r0 ACPIAM) [ 0.000000] ACPI: RSDT CFFB0000, 003C (r1 A M I OEMRSDT 12000731 MSFT 97) [ 0.000000] ACPI: FACP CFFB0200, 0084 (r2 A_M_I OEMFACP 12000601 MSFT 97) [ 0.000000] ACPI: DSDT CFFB0450, 4FFA (r1 ASR19 ASR19186 186 INTL 20051117) [ 0.000000] ACPI: FACS CFFC0000, 0040 [ 0.000000] ACPI: APIC CFFB0390, 0080 (r1 A M I OEMAPIC 12000731 MSFT 97) [ 0.000000] ACPI: MCFG CFFB0410, 003C (r1 A M I OEMMCFG 12000731 MSFT 97) [ 0.000000] ACPI: OEMB CFFC0040, 0060 (r1 A M I AMI_OEM 12000731 MSFT 97) [ 0.000000] ACPI: HPET CFFB5450, 0038 (r1 A M I OEMHPET0 12000731 MSFT 97) [ 0.000000] ACPI: SSDT CFFB5490, 030E (r1 A M I POWERNOW 1 AMD 1) [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used [ 0.000000] Entering add_active_range(0, 256, 851888) 1 entries of 256 used [ 0.000000] Entering add_active_range(0, 1048576, 1245184) 2 entries of 256 used [ 0.000000] No mptable found. [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] DMA32 4096 -> 1048576 [ 0.000000] Normal 1048576 -> 1245184 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[3] active PFN ranges [ 0.000000] 0: 0 -> 159 [ 0.000000] 0: 256 -> 851888 [ 0.000000] 0: 1048576 -> 1245184 [ 0.000000] On node 0 totalpages: 1048399 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 853 pages reserved [ 0.000000] DMA zone: 3090 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 14280 pages used for memmap [ 0.000000] DMA32 zone: 833512 pages, LIFO batch:31 [ 0.000000] Normal zone: 2688 pages used for memmap [ 0.000000] Normal zone: 193920 pages, LIFO batch:31 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] ACPI: PM-Timer IO Port: 0x2008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) [ 0.000000] Processor #1 [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] ACPI: IRQ14 used by override. [ 0.000000] ACPI: IRQ15 used by override. [ 0.000000] Setting APIC routing to flat [ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000 [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e6000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000e6000 - 0000000000100000 [ 0.000000] swsusp: Registered nosave memory region: 00000000cffb0000 - 00000000cffc0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000cffc0000 - 00000000cfff0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000cfff0000 - 00000000d0000000 [ 0.000000] swsusp: Registered nosave memory region: 00000000d0000000 - 00000000fec00000 [ 0.000000] swsusp: Registered nosave memory region: 00000000fec00000 - 00000000fec01000 [ 0.000000] swsusp: Registered nosave memory region: 00000000fec01000 - 00000000fee00000 [ 0.000000] swsusp: Registered nosave memory region: 00000000fee00000 - 00000000fef00000 [ 0.000000] swsusp: Registered nosave memory region: 00000000fef00000 - 00000000ff380000 [ 0.000000] swsusp: Registered nosave memory region: 00000000ff380000 - 0000000100000000 [ 0.000000] Allocating PCI resources starting at d4000000 (gap: d0000000:2ec00000) [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs [ 0.000000] PERCPU: Allocating 31408 bytes of per cpu data [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1030522 [ 0.000000] Kernel command line: root=/dev/sda3 nmi_watchdog=0 console=tty6 pci=nomsi [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 0.000000] hpet clockevent registered [ 0.000000] TSC calibrated against HPET [ 34.594710] Marking TSC unstable due to TSCs unsynchronized [ 34.594711] time.c: Detected 3013.887 MHz processor. [ 34.598537] Console: colour VGA+ 80x25 [ 34.598539] console [tty6] enabled [ 34.603172] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 34.605402] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 34.606172] Checking aperture... [ 34.606210] CPU 0: aperture @ ecca000000 size 32 MB [ 34.606247] Aperture too small (32 MB) [ 34.612116] No AGP bridge found [ 34.612152] Your BIOS doesn't leave a aperture memory hole [ 34.612190] Please enable the IOMMU option in the BIOS setup [ 34.612228] This costs you 64 MB of RAM [ 34.637460] Mapping aperture over 65536 KB of RAM @ 8000000 [ 34.661594] Memory: 4049948k/4980736k available (2192k kernel code, 143428k reserved, 681k data, 176k init) [ 34.661662] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1 [ 34.744360] Calibrating delay using timer specific routine.. 6034.68 BogoMIPS (lpj=10053891) [ 34.744453] Mount-cache hash table entries: 256 [ 34.744559] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 34.744599] CPU: L2 Cache: 1024K (64 bytes/line) [ 34.744637] CPU: Physical Processor ID: 0 [ 34.744673] CPU: Processor Core ID: 0 [ 34.744726] SMP alternatives: switching to UP code [ 34.745090] ACPI: Core revision 20070126 [ 34.780262] Using local APIC timer interrupts. [ 34.813406] APIC timer calibration result 12557872 [ 34.813408] Detected 12.557 MHz APIC timer. [ 34.813493] SMP alternatives: switching to SMP code [ 34.813723] Booting processor 1/2 APIC 0x1 [ 34.823842] Initializing CPU#1 [ 34.906605] Calibrating delay using timer specific routine.. 6030.92 BogoMIPS (lpj=10046281) [ 34.906609] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 34.906611] CPU: L2 Cache: 1024K (64 bytes/line) [ 34.906612] CPU: Physical Processor ID: 0 [ 34.906613] CPU: Processor Core ID: 1 [ 34.906694] AMD Athlon(tm) 64 X2 Dual Core Processor 6000+ stepping 03 [ 34.906751] Brought up 2 CPUs [ 34.907209] net_namespace: 120 bytes [ 34.907441] NET: Registered protocol family 16 [ 34.907553] ACPI: bus type pci registered [ 34.907635] PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved [ 34.907674] PCI: Not using MMCONFIG. [ 34.907710] PCI: Using configuration type 1 [ 34.909951] ACPI: EC: Look up EC in DSDT [ 34.913397] ACPI: Interpreter enabled [ 34.913434] ACPI: (supports S0 S1 S3 S4 S5) [ 34.913604] ACPI: Using IOAPIC for interrupt routing [ 34.913814] Error attaching device data [ 34.913853] Error attaching device data [ 34.913892] Error attaching device data [ 34.913930] Error attaching device data [ 34.918844] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 34.919369] PCI: Transparent bridge - 0000:00:08.0 [ 34.919663] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 34.919795] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] [ 34.919892] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR10._PRT] [ 34.919948] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR11._PRT] [ 34.920002] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR13._PRT] [ 34.920058] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR12._PRT] [ 34.923995] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *11 [ 34.924331] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *5 [ 34.924666] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled. [ 34.925027] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled. [ 34.925387] ACPI: PCI Interrupt Link [LNEA] (IRQs 16 17 18 19) *0, disabled. [ 34.925747] ACPI: PCI Interrupt Link [LNEB] (IRQs 16 17 18 19) *10 [ 34.926081] ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *0, disabled. [ 34.926441] ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *10 [ 34.926777] ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *5 [ 34.927112] ACPI: PCI Interrupt Link [LMAD] (IRQs 20 21 22 23) *0, disabled. [ 34.927472] ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *7 [ 34.927807] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0, disabled. [ 34.928167] ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *0, disabled. [ 34.928528] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *11 [ 34.928862] ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *0, disabled. [ 34.929223] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *15 [ 34.929557] ACPI: PCI Interrupt Link [LSA1] (IRQs 20 21 22 23) *0, disabled. [ 34.929954] ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled. [ 34.930315] ACPI: PCI Interrupt Link [UB11] (IRQs 20 21 22 23) *0, disabled. [ 34.930676] ACPI: PCI Interrupt Link [UB12] (IRQs 20 21 22 23) *0, disabled. [ 34.930995] Linux Plug and Play Support v0.97 (c) Adam Belay [ 34.931048] pnp: PnP ACPI init [ 34.931087] ACPI: bus type pnp registered [ 34.933625] pnp: PnP ACPI: found 13 devices [ 34.933662] ACPI: ACPI bus type pnp unregistered [ 34.933785] SCSI subsystem initialized [ 34.933842] libata version 3.00 loaded. [ 34.933892] usbcore: registered new interface driver usbfs [ 34.933948] usbcore: registered new interface driver hub [ 34.934004] usbcore: registered new device driver usb [ 34.934088] PCI: Using ACPI for IRQ routing [ 34.934125] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 34.943200] PCI-DMA: Disabling AGP. [ 34.943936] PCI-DMA: aperture base @ 8000000 size 65536 KB [ 34.943978] PCI-DMA: using GART IOMMU. [ 34.944017] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture [ 34.944176] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31 [ 34.944316] hpet0: 3 32-bit timers, 25000000 Hz [ 34.946485] Time: hpet clocksource has been installed. [ 34.946534] Switched to high resolution mode on CPU 0 [ 34.946623] Switched to high resolution mode on CPU 1 [ 34.953217] system 00:05: ioport range 0x4d0-0x4d1 has been reserved [ 34.956617] system 00:05: ioport range 0x800-0x80f has been reserved [ 34.956656] system 00:05: ioport range 0x2000-0x207f has been reserved [ 34.956696] system 00:05: ioport range 0x2080-0x20ff has been reserved [ 34.956735] system 00:05: ioport range 0x2400-0x247f has been reserved [ 34.956774] system 00:05: ioport range 0x2480-0x24ff has been reserved [ 34.956814] system 00:05: ioport range 0x2800-0x287f has been reserved [ 34.956853] system 00:05: ioport range 0x2880-0x28ff has been reserved [ 34.956892] system 00:05: ioport range 0x2c00-0x2c7f has been reserved [ 34.956931] system 00:05: ioport range 0x2c80-0x2cff has been reserved [ 34.956971] system 00:05: iomem range 0x0-0x0 could not be reserved [ 34.957011] system 00:05: iomem range 0xfee01000-0xfeefffff has been reserved [ 34.957055] system 00:07: iomem range 0xfec00000-0xfec00fff could not be reserved [ 34.957102] system 00:07: iomem range 0xfee00000-0xfee00fff could not be reserved [ 34.957153] system 00:0a: ioport range 0x290-0x29f has been reserved [ 34.957196] system 00:0b: iomem range 0xe0000000-0xefffffff has been reserved [ 34.957241] system 00:0c: iomem range 0x0-0x9ffff could not be reserved [ 34.957280] system 00:0c: iomem range 0xc0000-0xcffff has been reserved [ 34.957323] system 00:0c: iomem range 0xe0000-0xfffff could not be reserved [ 34.957363] system 00:0c: iomem range 0x100000-0xcfffffff could not be reserved [ 34.957410] system 00:0c: iomem range 0xff380000-0xffffffff could not be reserved [ 34.957692] PCI: Bridge: 0000:00:08.0 [ 34.957729] IO window: d000-dfff [ 34.957766] MEM window: f9f00000-f9ffffff [ 34.957804] PREFETCH window: disabled. [ 34.957841] PCI: Bridge: 0000:00:0b.0 [ 34.957878] IO window: c000-cfff [ 34.957914] MEM window: f9e00000-f9efffff [ 34.957951] PREFETCH window: disabled. [ 34.957988] PCI: Bridge: 0000:00:0c.0 [ 34.958024] IO window: disabled. [ 34.958061] MEM window: disabled. [ 34.958097] PREFETCH window: disabled. [ 34.958134] PCI: Bridge: 0000:00:0d.0 [ 34.958171] IO window: e000-efff [ 34.958207] MEM window: fa000000-febfffff [ 34.958244] PREFETCH window: d0000000-dfffffff [ 34.958282] PCI: Bridge: 0000:00:0e.0 [ 34.958318] IO window: disabled. [ 34.958354] MEM window: disabled. [ 34.958391] PREFETCH window: disabled. [ 34.958433] PCI: Setting latency timer of device 0000:00:08.0 to 64 [ 34.958442] PCI: Setting latency timer of device 0000:00:0b.0 to 64 [ 34.958447] PCI: Setting latency timer of device 0000:00:0c.0 to 64 [ 34.958452] PCI: Setting latency timer of device 0000:00:0d.0 to 64 [ 34.958456] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 34.958462] NET: Registered protocol family 2 [ 34.989784] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 34.990379] TCP established hash table entries: 262144 (order: 10, 4194304 bytes) [ 34.991804] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 34.992283] TCP: Hash tables configured (established 262144 bind 65536) [ 34.992323] TCP reno registered [ 35.000566] Loading Reiser4. See www.namesys.com for a description of Reiser4. [ 35.000670] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 35.000717] io scheduler noop registered [ 35.000756] io scheduler cfq registered (default) [ 35.001452] Boot video device is 0000:04:00.0 [ 35.001555] PCI: Setting latency timer of device 0000:00:0b.0 to 64 [ 35.001572] assign_interrupt_mode Found MSI capability [ 35.001613] Allocate Port Service[0000:00:0b.0:pcie00] [ 35.001655] PCI: Setting latency timer of device 0000:00:0c.0 to 64 [ 35.001671] assign_interrupt_mode Found MSI capability [ 35.001709] Allocate Port Service[0000:00:0c.0:pcie00] [ 35.001745] PCI: Setting latency timer of device 0000:00:0d.0 to 64 [ 35.001761] assign_interrupt_mode Found MSI capability [ 35.001800] Allocate Port Service[0000:00:0d.0:pcie00] [ 35.001837] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 35.001853] assign_interrupt_mode Found MSI capability [ 35.001891] Allocate Port Service[0000:00:0e.0:pcie00] [ 35.002065] input: Power Button (FF) as /class/input/input0 [ 35.002103] ACPI: Power Button (FF) [PWRF] [ 35.002188] input: Power Button (CM) as /class/input/input1 [ 35.002227] ACPI: Power Button (CM) [PWRB] [ 35.002361] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126] [ 35.002466] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126] [ 35.026407] Real Time Clock Driver v1.12ac [ 35.026526] hpet_resources: 0xfed00000 is busy [ 35.026543] Linux agpgart interface v0.102 [ 35.026629] Driver 'sd' needs updating - please use bus_type methods [ 35.026702] ahci 0000:00:0a.0: version 3.0 [ 35.026877] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23 [ 35.026922] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LSA0] -> GSI 23 (level, low) -> IRQ 23 [ 36.029726] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode [ 36.029777] ahci 0000:00:0a.0: flags: 64bit sntf led clo pmp pio [ 36.029817] PCI: Setting latency timer of device 0000:00:0a.0 to 64 [ 36.030019] scsi0 : ahci [ 36.030114] scsi1 : ahci [ 36.030180] scsi2 : ahci [ 36.030245] scsi3 : ahci [ 36.030333] ata1: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc100 irq 23 [ 36.030381] ata2: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc180 irq 23 [ 36.030428] ata3: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc200 irq 23 [ 36.030476] ata4: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc280 irq 23 [ 36.659406] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 36.660019] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133 [ 36.660062] ata1.00: 312581808 sectors, multi 16: LBA48 [ 36.660680] ata1.00: configured for UDMA/133 [ 37.291368] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 37.311928] ata2.00: ATA-8: SAMSUNG HD501LJ, CR100-12, max UDMA7 [ 37.311968] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 37.313968] ata2.00: configured for UDMA/133 [ 37.630631] ata3: SATA link down (SStatus 0 SControl 300) [ 37.949937] ata4: SATA link down (SStatus 0 SControl 300) [ 37.950026] scsi 0:0:0:0: Direct-Access ATA WDC WD1600JS-00M 10.0 PQ: 0 ANSI: 5 [ 37.950136] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) [ 37.950181] sd 0:0:0:0: [sda] Write Protect is off [ 37.950219] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 37.950227] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 37.950297] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) [ 37.950340] sd 0:0:0:0: [sda] Write Protect is off [ 37.950378] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 37.950385] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 37.950434] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [ 37.984324] sd 0:0:0:0: [sda] Attached SCSI disk [ 37.984459] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10 PQ: 0 ANSI: 5 [ 37.984568] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [ 37.984612] sd 1:0:0:0: [sdb] Write Protect is off [ 37.984650] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 37.984659] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 37.984729] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [ 37.984772] sd 1:0:0:0: [sdb] Write Protect is off [ 37.984810] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 37.984817] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 37.984866] sdb: sdb1 sdb2 [ 37.994164] sd 1:0:0:0: [sdb] Attached SCSI disk [ 37.994301] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 [ 37.996942] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 37.996982] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 38.027362] usbcore: registered new interface driver usbhid [ 38.027401] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 38.027445] TCP cubic registered [ 38.027484] NET: Registered protocol family 1 [ 38.027539] powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 6000+ processors (2 cpu cores) (version 2.20.00) [ 38.027584] powernow-k8: 0 : fid 0x16 (3000 MHz), vid 0x6 [ 38.027624] powernow-k8: 1 : fid 0x14 (2800 MHz), vid 0x8 [ 38.027662] powernow-k8: 2 : fid 0x12 (2600 MHz), vid 0xa [ 38.027700] powernow-k8: 3 : fid 0x10 (2400 MHz), vid 0xc [ 38.027738] powernow-k8: 4 : fid 0xe (2200 MHz), vid 0xe [ 38.027776] powernow-k8: 5 : fid 0xc (2000 MHz), vid 0x10 [ 38.027815] powernow-k8: 6 : fid 0xa (1800 MHz), vid 0x10 [ 38.027853] powernow-k8: 7 : fid 0x2 (1000 MHz), vid 0x12 [ 38.053987] input: AT Translated Set 2 keyboard as /class/input/input2 [ 38.146929] ReiserFS: sda3: found reiserfs format "3.6" with standard journal [ 38.146972] ReiserFS: sda3: using ordered data mode [ 38.156481] ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 [ 38.157392] ReiserFS: sda3: checking transaction log (sda3) [ 38.200787] ReiserFS: sda3: Using r5 hash to sort names [ 38.200838] VFS: Mounted root (reiserfs filesystem) readonly. [ 38.200887] Freeing unused kernel memory: 176k freed [ 38.480137] Clocksource tsc unstable (delta = -135289750 ns) [ 40.000024] ReiserFS: sda3: switching to journaled data mode [ 40.140567] r8169 Gigabit Ethernet driver 2.2LK loaded [ 40.140772] ACPI: PCI Interrupt Link [LNEB] enabled at IRQ 19 [ 40.140777] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNEB] -> GSI 19 (level, low) -> IRQ 19 [ 40.140785] PCI: Setting latency timer of device 0000:01:00.0 to 64 [ 40.140790] r8169 0000:01:00.0: no MSI. Back to INTx. [ 40.140914] eth0: RTL8168b/8111b at 0xffffc20000170000, 00:19:66:47:f3:cb, XID 38000000 IRQ 19 [ 40.146015] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22 [ 40.146021] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUB2] -> GSI 22 (level, low) -> IRQ 22 [ 40.146171] PCI: Setting latency timer of device 0000:00:02.1 to 64 [ 40.146174] ehci_hcd 0000:00:02.1: EHCI Host Controller [ 40.146248] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 [ 40.146269] ehci_hcd 0000:00:02.1: debug port 1 [ 40.146271] PCI: cache line size of 64 is not supported by device 0000:00:02.1 [ 40.146278] ehci_hcd 0000:00:02.1: irq 22, io mem 0xf9dfec00 [ 40.149046] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 40.149116] usb usb1: configuration #1 chosen from 1 choice [ 40.149131] hub 1-0:1.0: USB hub found [ 40.149136] hub 1-0:1.0: 10 ports detected [ 40.258499] usb 1-3: new high speed USB device using ehci_hcd and address 2 [ 40.296057] reiser4: sdb2: found disk format 4.0.0. [ 40.301115] usb 1-3: configuration #1 chosen from 1 choice [ 40.301307] hub 1-3:1.0: USB hub found [ 40.302020] hub 1-3:1.0: 4 ports detected [ 40.398307] usb 1-3.1: new low speed USB device using ehci_hcd and address 3 [ 40.428288] usb 1-3.1: configuration #1 chosen from 1 choice [ 40.431891] input: Logitech USB Receiver as /class/input/input3 [ 40.437320] input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:02.1-3.1 [ 40.439385] input: Logitech USB Receiver as /class/input/input4 [ 40.455077] input: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:02.1-3.1 [ 40.463944] mice: PS/2 mouse device common for all mice [ 48.714006] reiser4: sda6: found disk format 4.0.0. [ 49.173963] reiser4: sdb1: found disk format 4.0.0. [ 49.537860] Adding 1951888k swap on /dev/sda2. Priority:-1 extents:1 across:1951888k [ 52.661003] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 18 [ 52.661012] ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNKB] -> GSI 18 (level, low) -> IRQ 18 [ 52.663793] Audigy2 value: Special config. [ 54.558692] w83627ehf: Found W83627EHG chip at 0x290 [ 55.654993] r8169: eth0: link up [ 55.655000] r8169: eth0: link up [ 56.073125] NET: Registered protocol family 17 [ 59.453903] nvidia: module license 'NVIDIA' taints kernel. [ 59.625059] ACPI: PCI Interrupt Link [LNED] enabled at IRQ 17 [ 59.625067] ACPI: PCI Interrupt 0000:04:00.0[A] -> Link [LNED] -> GSI 17 (level, low) -> IRQ 17 [ 59.625072] PCI: Setting latency timer of device 0000:04:00.0 to 64 [ 59.625155] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 171.06 Wed Feb 20 09:02:26 PST 2008