Hi, I tried some more stuff, replaced the cables, played with bios settings. No change. Then I updated to 2.6.24.3 - and no hangs or 'softreset' failures anymore. [ 38.151334] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode [ 38.151386] ahci 0000:00:0a.0: flags: 64bit sntf led clo pmp pio [ 38.151425] PCI: Setting latency timer of device 0000:00:0a.0 to 64 [ 38.151626] scsi0 : ahci [ 38.151722] scsi1 : ahci [ 38.151788] scsi2 : ahci [ 38.151853] scsi3 : ahci [ 38.151942] ata1: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc100 irq 315 [ 38.151990] ata2: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc180 irq 315 [ 38.152037] ata3: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc200 irq 315 [ 38.152085] ata4: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc280 irq 315 [ 38.783287] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 38.783915] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133 [ 38.783957] ata1.00: 312581808 sectors, multi 16: LBA48 [ 38.784590] ata1.00: configured for UDMA/133 [ 39.415249] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 39.435823] ata2.00: ATA-8: SAMSUNG HD501LJ, CR100-12, max UDMA7 [ 39.435862] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 39.437862] ata2.00: configured for UDMA/133 [ 39.754512] ata3: SATA link down (SStatus 0 SControl 300) [ 40.073818] ata4: SATA link down (SStatus 0 SControl 300) [ 40.073907] scsi 0:0:0:0: Direct-Access ATA WDC WD1600JS-00M 10.0 PQ: 0 ANSI: 5 [ 40.074017] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) [ 40.074061] sd 0:0:0:0: [sda] Write Protect is off [ 40.074099] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 40.074107] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 40.074178] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) [ 40.074220] sd 0:0:0:0: [sda] Write Protect is off [ 40.074258] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 40.074265] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 40.074314] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [ 40.098590] sd 0:0:0:0: [sda] Attached SCSI disk [ 40.098725] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10 PQ: 0 ANSI: 5 [ 40.098835] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [ 40.098879] sd 1:0:0:0: [sdb] Write Protect is off [ 40.098917] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 40.098926] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 40.098996] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [ 40.099039] sd 1:0:0:0: [sdb] Write Protect is off [ 40.099076] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 40.099084] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 40.099133] sdb: sdb1 sdb2 [ 40.109668] sd 1:0:0:0: [sdb] Attached SCSI disk The only change to other kernels was making ehci-hcd modular. I checked already, other kernels still have the IDENTITY error on coldboot and the softreset failure on reboot even with the changed config. 2.6.24.2 and 2.6.24.3 both have the reiser4 patch added. So 2.6.24.2 = bad 2.6.24.3 = good 2.6.25-rc5 = bad Setting AHCI in bios still results in timeouts and harddisks not found. Glück Auf, Volker
[ 0.000000] Linux version 2.6.24.3reiser4 (root@energy) (gcc version 4.2.3 (Gentoo 4.2.3 p1.0)) #1 SMP Sun Mar 16 20:32:58 CET 2008 [ 0.000000] Command line: root=/dev/sda3 nmi_watchdog=0 console=tty6 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000cffb0000 (usable) [ 0.000000] BIOS-e820: 00000000cffb0000 - 00000000cffc0000 (ACPI data) [ 0.000000] BIOS-e820: 00000000cffc0000 - 00000000cfff0000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000cfff0000 - 00000000d0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved) [ 0.000000] BIOS-e820: 00000000ff380000 - 0000000100000000 (reserved) [ 0.000000] BIOS-e820: 0000000100000000 - 0000000130000000 (usable) [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used [ 0.000000] Entering add_active_range(0, 256, 851888) 1 entries of 256 used [ 0.000000] Entering add_active_range(0, 1048576, 1245184) 2 entries of 256 used [ 0.000000] end_pfn_map = 1245184 [ 0.000000] DMI present. [ 0.000000] ACPI: RSDP 000F98E0, 0014 (r0 ACPIAM) [ 0.000000] ACPI: RSDT CFFB0000, 003C (r1 A M I OEMRSDT 12000731 MSFT 97) [ 0.000000] ACPI: FACP CFFB0200, 0084 (r2 A_M_I OEMFACP 12000601 MSFT 97) [ 0.000000] ACPI: DSDT CFFB0450, 4FFA (r1 ASR19 ASR19186 186 INTL 20051117) [ 0.000000] ACPI: FACS CFFC0000, 0040 [ 0.000000] ACPI: APIC CFFB0390, 0080 (r1 A M I OEMAPIC 12000731 MSFT 97) [ 0.000000] ACPI: MCFG CFFB0410, 003C (r1 A M I OEMMCFG 12000731 MSFT 97) [ 0.000000] ACPI: OEMB CFFC0040, 0060 (r1 A M I AMI_OEM 12000731 MSFT 97) [ 0.000000] ACPI: HPET CFFB5450, 0038 (r1 A M I OEMHPET0 12000731 MSFT 97) [ 0.000000] ACPI: SSDT CFFB5490, 030E (r1 A M I POWERNOW 1 AMD 1) [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used [ 0.000000] Entering add_active_range(0, 256, 851888) 1 entries of 256 used [ 0.000000] Entering add_active_range(0, 1048576, 1245184) 2 entries of 256 used [ 0.000000] No mptable found. [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] DMA32 4096 -> 1048576 [ 0.000000] Normal 1048576 -> 1245184 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[3] active PFN ranges [ 0.000000] 0: 0 -> 159 [ 0.000000] 0: 256 -> 851888 [ 0.000000] 0: 1048576 -> 1245184 [ 0.000000] On node 0 totalpages: 1048399 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 853 pages reserved [ 0.000000] DMA zone: 3090 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 14280 pages used for memmap [ 0.000000] DMA32 zone: 833512 pages, LIFO batch:31 [ 0.000000] Normal zone: 2688 pages used for memmap [ 0.000000] Normal zone: 193920 pages, LIFO batch:31 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] ACPI: PM-Timer IO Port: 0x2008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) [ 0.000000] Processor #1 [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] ACPI: IRQ14 used by override. [ 0.000000] ACPI: IRQ15 used by override. [ 0.000000] Setting APIC routing to flat [ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000 [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e6000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000e6000 - 0000000000100000 [ 0.000000] swsusp: Registered nosave memory region: 00000000cffb0000 - 00000000cffc0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000cffc0000 - 00000000cfff0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000cfff0000 - 00000000d0000000 [ 0.000000] swsusp: Registered nosave memory region: 00000000d0000000 - 00000000fec00000 [ 0.000000] swsusp: Registered nosave memory region: 00000000fec00000 - 00000000fec01000 [ 0.000000] swsusp: Registered nosave memory region: 00000000fec01000 - 00000000fee00000 [ 0.000000] swsusp: Registered nosave memory region: 00000000fee00000 - 00000000fef00000 [ 0.000000] swsusp: Registered nosave memory region: 00000000fef00000 - 00000000ff380000 [ 0.000000] swsusp: Registered nosave memory region: 00000000ff380000 - 0000000100000000 [ 0.000000] Allocating PCI resources starting at d4000000 (gap: d0000000:2ec00000) [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs [ 0.000000] PERCPU: Allocating 31408 bytes of per cpu data [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1030522 [ 0.000000] Kernel command line: root=/dev/sda3 nmi_watchdog=0 console=tty6 [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 0.000000] hpet clockevent registered [ 0.000000] TSC calibrated against HPET [ 27.321929] Marking TSC unstable due to TSCs unsynchronized [ 27.321931] time.c: Detected 3013.888 MHz processor. [ 27.325755] Console: colour VGA+ 80x25 [ 27.325757] console [tty6] enabled [ 27.330363] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 27.332590] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 27.333357] Checking aperture... [ 27.333395] CPU 0: aperture @ ecc8000000 size 32 MB [ 27.333433] Aperture too small (32 MB) [ 27.339291] No AGP bridge found [ 27.339327] Your BIOS doesn't leave a aperture memory hole [ 27.339365] Please enable the IOMMU option in the BIOS setup [ 27.339403] This costs you 64 MB of RAM [ 27.364634] Mapping aperture over 65536 KB of RAM @ 8000000 [ 27.388765] Memory: 4049948k/4980736k available (2192k kernel code, 143428k reserved, 681k data, 176k init) [ 27.388833] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1 [ 27.471580] Calibrating delay using timer specific routine.. 6034.70 BogoMIPS (lpj=10053931) [ 27.471673] Mount-cache hash table entries: 256 [ 27.471780] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 27.471819] CPU: L2 Cache: 1024K (64 bytes/line) [ 27.471857] CPU: Physical Processor ID: 0 [ 27.471894] CPU: Processor Core ID: 0 [ 27.471947] SMP alternatives: switching to UP code [ 27.472310] ACPI: Core revision 20070126 [ 27.507485] Using local APIC timer interrupts. [ 27.540630] APIC timer calibration result 12557876 [ 27.540631] Detected 12.557 MHz APIC timer. [ 27.540716] SMP alternatives: switching to SMP code [ 27.540945] Booting processor 1/2 APIC 0x1 [ 27.551054] Initializing CPU#1 [ 27.633818] Calibrating delay using timer specific routine.. 6030.92 BogoMIPS (lpj=10046282) [ 27.633822] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 27.633824] CPU: L2 Cache: 1024K (64 bytes/line) [ 27.633826] CPU: Physical Processor ID: 0 [ 27.633827] CPU: Processor Core ID: 1 [ 27.633908] AMD Athlon(tm) 64 X2 Dual Core Processor 6000+ stepping 03 [ 27.633973] Brought up 2 CPUs [ 27.634431] net_namespace: 120 bytes [ 27.634663] NET: Registered protocol family 16 [ 27.634775] ACPI: bus type pci registered [ 27.634857] PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved [ 27.634896] PCI: Not using MMCONFIG. [ 27.634932] PCI: Using configuration type 1 [ 27.637173] ACPI: EC: Look up EC in DSDT [ 27.640624] ACPI: Interpreter enabled [ 27.640662] ACPI: (supports S0 S1 S3 S4 S5) [ 27.640832] ACPI: Using IOAPIC for interrupt routing [ 27.641040] Error attaching device data [ 27.641080] Error attaching device data [ 27.641118] Error attaching device data [ 27.641157] Error attaching device data [ 27.646070] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 27.646594] PCI: Transparent bridge - 0000:00:08.0 [ 27.646888] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 27.647020] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] [ 27.647117] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR10._PRT] [ 27.647173] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR11._PRT] [ 27.647227] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR13._PRT] [ 27.647283] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR12._PRT] [ 27.651219] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *11 [ 27.651555] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *5 [ 27.651889] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled. [ 27.652249] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled. [ 27.652609] ACPI: PCI Interrupt Link [LNEA] (IRQs 16 17 18 19) *0, disabled. [ 27.652968] ACPI: PCI Interrupt Link [LNEB] (IRQs 16 17 18 19) *10 [ 27.653301] ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *0, disabled. [ 27.653661] ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *10 [ 27.653997] ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *5 [ 27.654331] ACPI: PCI Interrupt Link [LMAD] (IRQs 20 21 22 23) *0, disabled. [ 27.654690] ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *7 [ 27.655024] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0, disabled. [ 27.655383] ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *0, disabled. [ 27.655744] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *11 [ 27.656077] ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *0, disabled. [ 27.656437] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *15 [ 27.656772] ACPI: PCI Interrupt Link [LSA1] (IRQs 20 21 22 23) *0, disabled. [ 27.657169] ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled. [ 27.657528] ACPI: PCI Interrupt Link [UB11] (IRQs 20 21 22 23) *0, disabled. [ 27.657889] ACPI: PCI Interrupt Link [UB12] (IRQs 20 21 22 23) *0, disabled. [ 27.658207] Linux Plug and Play Support v0.97 (c) Adam Belay [ 27.658260] pnp: PnP ACPI init [ 27.658299] ACPI: bus type pnp registered [ 27.660838] pnp: PnP ACPI: found 13 devices [ 27.660875] ACPI: ACPI bus type pnp unregistered [ 27.660998] SCSI subsystem initialized [ 27.661055] libata version 3.00 loaded. [ 27.661105] usbcore: registered new interface driver usbfs [ 27.661161] usbcore: registered new interface driver hub [ 27.661218] usbcore: registered new device driver usb [ 27.661301] PCI: Using ACPI for IRQ routing [ 27.661339] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 27.670423] PCI-DMA: Disabling AGP. [ 27.671160] PCI-DMA: aperture base @ 8000000 size 65536 KB [ 27.671202] PCI-DMA: using GART IOMMU. [ 27.671241] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture [ 27.671400] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31 [ 27.671539] hpet0: 3 32-bit timers, 25000000 Hz [ 27.673708] Time: hpet clocksource has been installed. [ 27.673757] Switched to high resolution mode on CPU 0 [ 27.673837] Switched to high resolution mode on CPU 1 [ 27.680440] system 00:05: ioport range 0x4d0-0x4d1 has been reserved [ 27.680480] system 00:05: ioport range 0x800-0x80f has been reserved [ 27.680519] system 00:05: ioport range 0x2000-0x207f has been reserved [ 27.680559] system 00:05: ioport range 0x2080-0x20ff has been reserved [ 27.683951] system 00:05: ioport range 0x2400-0x247f has been reserved [ 27.683990] system 00:05: ioport range 0x2480-0x24ff has been reserved [ 27.684030] system 00:05: ioport range 0x2800-0x287f has been reserved [ 27.684069] system 00:05: ioport range 0x2880-0x28ff has been reserved [ 27.684108] system 00:05: ioport range 0x2c00-0x2c7f has been reserved [ 27.684148] system 00:05: ioport range 0x2c80-0x2cff has been reserved [ 27.684187] system 00:05: iomem range 0x0-0x0 could not be reserved [ 27.684227] system 00:05: iomem range 0xfee01000-0xfeefffff has been reserved [ 27.684271] system 00:07: iomem range 0xfec00000-0xfec00fff could not be reserved [ 27.684318] system 00:07: iomem range 0xfee00000-0xfee00fff could not be reserved [ 27.684369] system 00:0a: ioport range 0x290-0x29f has been reserved [ 27.684411] system 00:0b: iomem range 0xe0000000-0xefffffff has been reserved [ 27.684457] system 00:0c: iomem range 0x0-0x9ffff could not be reserved [ 27.684496] system 00:0c: iomem range 0xc0000-0xcffff has been reserved [ 27.684535] system 00:0c: iomem range 0xe0000-0xfffff could not be reserved [ 27.684579] system 00:0c: iomem range 0x100000-0xcfffffff could not be reserved [ 27.684626] system 00:0c: iomem range 0xff380000-0xffffffff could not be reserved [ 27.684908] PCI: Bridge: 0000:00:08.0 [ 27.684945] IO window: d000-dfff [ 27.684982] MEM window: f9f00000-f9ffffff [ 27.685020] PREFETCH window: disabled. [ 27.685057] PCI: Bridge: 0000:00:0b.0 [ 27.685094] IO window: c000-cfff [ 27.685130] MEM window: f9e00000-f9efffff [ 27.685167] PREFETCH window: disabled. [ 27.685204] PCI: Bridge: 0000:00:0c.0 [ 27.685240] IO window: disabled. [ 27.685277] MEM window: disabled. [ 27.685313] PREFETCH window: disabled. [ 27.685350] PCI: Bridge: 0000:00:0d.0 [ 27.685386] IO window: e000-efff [ 27.685423] MEM window: fa000000-febfffff [ 27.685460] PREFETCH window: d0000000-dfffffff [ 27.685497] PCI: Bridge: 0000:00:0e.0 [ 27.685534] IO window: disabled. [ 27.685570] MEM window: disabled. [ 27.685606] PREFETCH window: disabled. [ 27.685649] PCI: Setting latency timer of device 0000:00:08.0 to 64 [ 27.685657] PCI: Setting latency timer of device 0000:00:0b.0 to 64 [ 27.685662] PCI: Setting latency timer of device 0000:00:0c.0 to 64 [ 27.685667] PCI: Setting latency timer of device 0000:00:0d.0 to 64 [ 27.685672] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 27.685678] NET: Registered protocol family 2 [ 27.717007] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 27.717603] TCP established hash table entries: 262144 (order: 10, 4194304 bytes) [ 27.719026] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 27.719509] TCP: Hash tables configured (established 262144 bind 65536) [ 27.719549] TCP reno registered [ 27.727790] Loading Reiser4. See www.namesys.com for a description of Reiser4. [ 27.727894] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 27.727942] io scheduler noop registered [ 27.727980] io scheduler cfq registered (default) [ 27.728676] Boot video device is 0000:04:00.0 [ 27.728779] PCI: Setting latency timer of device 0000:00:0b.0 to 64 [ 27.728796] assign_interrupt_mode Found MSI capability [ 27.728849] Allocate Port Service[0000:00:0b.0:pcie00] [ 27.728891] PCI: Setting latency timer of device 0000:00:0c.0 to 64 [ 27.728907] assign_interrupt_mode Found MSI capability [ 27.728955] Allocate Port Service[0000:00:0c.0:pcie00] [ 27.728992] PCI: Setting latency timer of device 0000:00:0d.0 to 64 [ 27.729008] assign_interrupt_mode Found MSI capability [ 27.729056] Allocate Port Service[0000:00:0d.0:pcie00] [ 27.729094] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 27.729110] assign_interrupt_mode Found MSI capability [ 27.729158] Allocate Port Service[0000:00:0e.0:pcie00] [ 27.729331] input: Power Button (FF) as /class/input/input0 [ 27.729369] ACPI: Power Button (FF) [PWRF] [ 27.729455] input: Power Button (CM) as /class/input/input1 [ 27.729493] ACPI: Power Button (CM) [PWRB] [ 27.729627] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126] [ 27.729732] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126] [ 27.753629] Real Time Clock Driver v1.12ac [ 27.753749] hpet_resources: 0xfed00000 is busy [ 27.753766] Linux agpgart interface v0.102 [ 27.753851] Driver 'sd' needs updating - please use bus_type methods [ 27.753925] ahci 0000:00:0a.0: version 3.0 [ 27.754100] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23 [ 27.754143] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LSA0] -> GSI 23 (level, low) -> IRQ 23 [ 28.754676] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode [ 28.754728] ahci 0000:00:0a.0: flags: 64bit sntf led clo pmp pio [ 28.754767] PCI: Setting latency timer of device 0000:00:0a.0 to 64 [ 28.754969] scsi0 : ahci [ 28.755064] scsi1 : ahci [ 28.755130] scsi2 : ahci [ 28.755196] scsi3 : ahci [ 28.755284] ata1: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc100 irq 315 [ 28.755332] ata2: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc180 irq 315 [ 28.755379] ata3: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc200 irq 315 [ 28.755426] ata4: SATA max UDMA/133 abar m8192@0xf9dfc000 port 0xf9dfc280 irq 315 [ 29.386629] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 29.387240] ata1.00: ATA-7: WDC WD1600JS-00MHB1, 10.02E01, max UDMA/133 [ 29.387283] ata1.00: 312581808 sectors, multi 16: LBA48 [ 29.387918] ata1.00: configured for UDMA/133 [ 30.018591] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 30.039146] ata2.00: ATA-8: SAMSUNG HD501LJ, CR100-12, max UDMA7 [ 30.039186] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 30.041191] ata2.00: configured for UDMA/133 [ 30.357854] ata3: SATA link down (SStatus 0 SControl 300) [ 30.677160] ata4: SATA link down (SStatus 0 SControl 300) [ 30.677249] scsi 0:0:0:0: Direct-Access ATA WDC WD1600JS-00M 10.0 PQ: 0 ANSI: 5 [ 30.677359] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) [ 30.677404] sd 0:0:0:0: [sda] Write Protect is off [ 30.677442] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 30.677450] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 30.677520] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) [ 30.677563] sd 0:0:0:0: [sda] Write Protect is off [ 30.677601] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 30.677608] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 30.677657] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [ 30.713124] sd 0:0:0:0: [sda] Attached SCSI disk [ 30.713259] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10 PQ: 0 ANSI: 5 [ 30.713368] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [ 30.713412] sd 1:0:0:0: [sdb] Write Protect is off [ 30.713450] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 30.713459] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 30.713529] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB) [ 30.713572] sd 1:0:0:0: [sdb] Write Protect is off [ 30.713610] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 30.713617] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 30.713666] sdb: sdb1 sdb2 [ 30.720847] sd 1:0:0:0: [sdb] Attached SCSI disk [ 30.720984] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 [ 30.723565] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 30.723604] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 30.757909] usbcore: registered new interface driver usbhid [ 30.757947] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 30.757991] TCP cubic registered [ 30.758030] NET: Registered protocol family 1 [ 30.758087] powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 6000+ processors (2 cpu cores) (version 2.20.00) [ 30.758143] powernow-k8: 0 : fid 0x16 (3000 MHz), vid 0x6 [ 30.758183] powernow-k8: 1 : fid 0x14 (2800 MHz), vid 0x8 [ 30.758221] powernow-k8: 2 : fid 0x12 (2600 MHz), vid 0xa [ 30.758259] powernow-k8: 3 : fid 0x10 (2400 MHz), vid 0xc [ 30.758297] powernow-k8: 4 : fid 0xe (2200 MHz), vid 0xe [ 30.758335] powernow-k8: 5 : fid 0xc (2000 MHz), vid 0x10 [ 30.758373] powernow-k8: 6 : fid 0xa (1800 MHz), vid 0x10 [ 30.758411] powernow-k8: 7 : fid 0x2 (1000 MHz), vid 0x12 [ 30.785840] input: AT Translated Set 2 keyboard as /class/input/input2 [ 30.884040] ReiserFS: sda3: found reiserfs format "3.6" with standard journal [ 30.884083] ReiserFS: sda3: using ordered data mode [ 30.893590] ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 [ 30.894500] ReiserFS: sda3: checking transaction log (sda3) [ 30.937895] ReiserFS: sda3: Using r5 hash to sort names [ 30.937946] VFS: Mounted root (reiserfs filesystem) readonly. [ 30.937996] Freeing unused kernel memory: 176k freed [ 31.240623] Clocksource tsc unstable (delta = -101952042 ns) [ 32.785186] ReiserFS: sda3: switching to journaled data mode [ 33.851423] r8169 Gigabit Ethernet driver 2.2LK loaded [ 33.851628] ACPI: PCI Interrupt Link [LNEB] enabled at IRQ 19 [ 33.851633] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNEB] -> GSI 19 (level, low) -> IRQ 19 [ 33.851642] PCI: Setting latency timer of device 0000:01:00.0 to 64 [ 33.851789] eth0: RTL8168b/8111b at 0xffffc20000170000, 00:19:66:47:f3:cb, XID 38000000 IRQ 314 [ 33.855223] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22 [ 33.855229] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUB2] -> GSI 22 (level, low) -> IRQ 22 [ 33.855374] PCI: Setting latency timer of device 0000:00:02.1 to 64 [ 33.855377] ehci_hcd 0000:00:02.1: EHCI Host Controller [ 33.855458] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 [ 33.855480] ehci_hcd 0000:00:02.1: debug port 1 [ 33.855483] PCI: cache line size of 64 is not supported by device 0000:00:02.1 [ 33.855489] ehci_hcd 0000:00:02.1: irq 22, io mem 0xf9dfec00 [ 33.858684] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 33.858754] usb usb1: configuration #1 chosen from 1 choice [ 33.858768] hub 1-0:1.0: USB hub found [ 33.858773] hub 1-0:1.0: 10 ports detected [ 33.969146] usb 1-3: new high speed USB device using ehci_hcd and address 2 [ 33.994089] reiser4: sdb2: found disk format 4.0.0. [ 34.009535] usb 1-3: configuration #1 chosen from 1 choice [ 34.009727] hub 1-3:1.0: USB hub found [ 34.010451] hub 1-3:1.0: 4 ports detected [ 34.106728] usb 1-3.1: new low speed USB device using ehci_hcd and address 3 [ 34.141157] usb 1-3.1: configuration #1 chosen from 1 choice [ 34.144754] input: Logitech USB Receiver as /class/input/input3 [ 34.153515] input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:02.1-3.1 [ 34.155582] input: Logitech USB Receiver as /class/input/input4 [ 34.160990] mice: PS/2 mouse device common for all mice [ 34.175696] input: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:02.1-3.1 [ 42.876614] reiser4: sda6: found disk format 4.0.0. [ 43.324415] reiser4: sdb1: found disk format 4.0.0. [ 43.741998] Adding 1951888k swap on /dev/sda2. Priority:-1 extents:1 across:1951888k [ 45.013198] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 18 [ 45.013203] ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNKB] -> GSI 18 (level, low) -> IRQ 18 [ 45.014300] Audigy2 value: Special config. [ 46.597359] w83627ehf: Found W83627EHG chip at 0x290 [ 47.883333] r8169: eth0: link up [ 47.883342] r8169: eth0: link up [ 48.563063] NET: Registered protocol family 17 [ 51.559910] nvidia: module license 'NVIDIA' taints kernel. [ 51.731619] ACPI: PCI Interrupt Link [LNED] enabled at IRQ 17 [ 51.731627] ACPI: PCI Interrupt 0000:04:00.0[A] -> Link [LNED] -> GSI 17 (level, low) -> IRQ 17 [ 51.731632] PCI: Setting latency timer of device 0000:04:00.0 to 64 [ 51.731723] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 171.06 Wed Feb 20 09:02:26 PST 2008
