Jeff Garzik wrote:
Tejun Heo wrote:
Hellooooo, all.
Finally, the last one. This is the first take of add-hotplug-support
patchset. This patchset includes 13 patches.
#01-04 implement hotplug framework
#05-07 implement warm plug (SCSI scan/delete callbacks)
#08-10 hook and activate hotplug
#11-13 add LLDD hotplug supports (PHY status change notifications)
Hotplugging is implemented as an integral part of EH. A new EH helper
ata_eh_hotplug() is defined which should be called after all regular
EH is done. LLDDs have to do very little to support hotplug.
I'm going to leave the substantive review of this patchset for the next
time it gets resent.
Yeap, please don't spend too much time on it. Hotplug has been changed
quite a bit in my current repo.
Overall,
* my quick review didn't turn up any obvious problems, but that was just
looking at each patch, not looking at the end result (big picture) at all.
* hotplug design I want to see is (also mentioned in another email):
1a) user requests bus scan
or
1b) hotplug interrupt
2) wait a bit, swallowing any 1a- or 1b-type events that
appear during the wait (debounce).
3) rescan bus, revalidate device(s)
In my working repo, hardware debouncing is done by invoking the
following function in ->prereset() with the port frozen. I'm not very
sure whether debouncing user request is necessary though.
/**
* sata_debounce - debounce SATA phy status
* @link: ATA link to debounce SATA phy status for
* @interval_msec: polling interval in millisecs
* @duration_msec: debounce duration in millisecs
* @timeout_msec: timeout in millisecs
*
* Make sure SStatus of @link reaches stable state, determined by
* holding the same value where DET is not 1 for @duration_msec
* polled every @interval_msec, before @timeout_msec. Note the
* timeout constraints the beginning of the stable state.
*
* LOCKING:
* Kernel thread context (may sleep)
*
* RETURNS:
* 0 on success, -errno on failure.
*/
int sata_debounce(struct ata_link *link, unsigned long interval_msec,
unsigned long duration_msec, unsigned long timeout_msec)
{
unsigned long duration = duration_msec * HZ / 1000;
unsigned long timeout = jiffies + timeout_msec * HZ / 1000;
unsigned long last_jiffies;
u32 last, cur;
int rc;
if ((rc = ata_scr_read(link, SCR_STATUS, &cur)))
return rc;
cur &= 0xf;
last = cur;
last_jiffies = jiffies;
while (1) {
msleep(interval_msec);
if ((rc = ata_scr_read(link, SCR_STATUS, &cur)))
return rc;
cur &= 0xf;
/* DET stable? */
if (cur == last && cur != 1) {
if (time_after(jiffies, last_jiffies + duration))
return 0;
continue;
}
/* unstable, start over */
last = cur;
last_jiffies = jiffies;
/* check timeout */
if (time_after(jiffies, timeout))
return -EBUSY;
}
}
I'm careful to use "revalidate", because that covers all cases:
- existing device goes away
- new device appears
- existing device "blipped", but its still there, so
we can keep talking to it.
Yeap, all bases covered.
I'm currently finishing up PM support. It took a lot longer than I
though but it's shaping up pretty good. Everything is handled nicely,
hotplug, EH, qc deferring (e.g. not issuing ATAPI command if commands
are outstanding to more than three devices for sil24...) are all handled
in generic and unified way. Adding PM support necessitated quite a bit
of changes to EH and hotplug. Currently, major changes in my repo are...
- boot scan, hotplug, EH all rolled up into single EH revive operation.
- simpler EH/irq synchronization. EH now works on its own copy of EH
info created on entry to EH.
- much tighter event handling (almost no EH/hotplug event/info loss
except for pathological cases)
- fine-grained user scan request (user can request scan of specific device)
- ata_link abstraction for PM
- PM support with the same level of EH/NCQ/hotplug support as host ports
(sil24 and working on AHCI)
Above list is what comes to my mind ATM. I probably have forgotten a
lot. I'll make a full list when I post the next round of patches.
Jeff, until when are you available? I think I can post the next round
in a few days (I'm pretty sure this time :). I'm thinking of setting up
a git repo and merge irq-pio there too in the order you requested. If
schedule isn't too tight, it would be nice to push this thing to some
branch in libata-dev.
Thanks.
--
tejun
-
: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
