[PATCH 2/6] pinctrl: sunxi: Add I/O bias setting for H6 R-PIO

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



H6 requires I/O bias configuration on both of its PIO devices.
Previously it was only done for the main PIO.

The setting for Port L is at bit 0, so the bank calculation needs to
account for the pin base. Otherwise the wrong bit is used.

Fixes: cc62383fcebe ("pinctrl: sunxi: Support I/O bias voltage setting on H6")
Signed-off-by: Samuel Holland <samuel@xxxxxxxxxxxx>
---

 drivers/pinctrl/sunxi/pinctrl-sun50i-h6-r.c | 1 +
 drivers/pinctrl/sunxi/pinctrl-sunxi.c       | 7 ++++---
 2 files changed, 5 insertions(+), 3 deletions(-)

diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-h6-r.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-h6-r.c
index c7d90c44e87a..7b4b9f3d4555 100644
--- a/drivers/pinctrl/sunxi/pinctrl-sun50i-h6-r.c
+++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-h6-r.c
@@ -107,6 +107,7 @@ static const struct sunxi_pinctrl_desc sun50i_h6_r_pinctrl_data = {
 	.npins = ARRAY_SIZE(sun50i_h6_r_pins),
 	.pin_base = PL_BASE,
 	.irq_banks = 2,
+	.io_bias_cfg_variant = BIAS_VOLTAGE_PIO_POW_MODE_SEL,
 };
 
 static int sun50i_h6_r_pinctrl_probe(struct platform_device *pdev)
diff --git a/drivers/pinctrl/sunxi/pinctrl-sunxi.c b/drivers/pinctrl/sunxi/pinctrl-sunxi.c
index d9327d7d56ee..3c5e71359ca8 100644
--- a/drivers/pinctrl/sunxi/pinctrl-sunxi.c
+++ b/drivers/pinctrl/sunxi/pinctrl-sunxi.c
@@ -622,7 +622,7 @@ static int sunxi_pinctrl_set_io_bias_cfg(struct sunxi_pinctrl *pctl,
 					 unsigned pin,
 					 struct regulator *supply)
 {
-	unsigned short bank = pin / PINS_PER_BANK;
+	unsigned short bank;
 	unsigned long flags;
 	u32 val, reg;
 	int uV;
@@ -638,6 +638,9 @@ static int sunxi_pinctrl_set_io_bias_cfg(struct sunxi_pinctrl *pctl,
 	if (uV == 0)
 		return 0;
 
+	pin -= pctl->desc->pin_base;
+	bank = pin / PINS_PER_BANK;
+
 	switch (pctl->desc->io_bias_cfg_variant) {
 	case BIAS_VOLTAGE_GRP_CONFIG:
 		/*
@@ -655,8 +658,6 @@ static int sunxi_pinctrl_set_io_bias_cfg(struct sunxi_pinctrl *pctl,
 		else
 			val = 0xD; /* 3.3V */
 
-		pin -= pctl->desc->pin_base;
-
 		reg = readl(pctl->membase + sunxi_grp_config_reg(pin));
 		reg &= ~IO_BIAS_MASK;
 		writel(reg | val, pctl->membase + sunxi_grp_config_reg(pin));
-- 
2.35.1




[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux