On Fri, Mar 05, 2021 at 01:21:51PM +0100, Sedat Dilek wrote: > On Fri, Mar 5, 2021 at 1:00 PM Lukas Czerner <lczerner@xxxxxxxxxx> wrote: > > > > On Mon, Mar 01, 2021 at 04:42:26PM +0100, Sedat Dilek wrote: > > > On Mon, Mar 1, 2021 at 4:34 PM Theodore Ts'o <tytso@xxxxxxx> wrote: > > > > > > > > On Mon, Mar 01, 2021 at 04:12:03PM +0100, Sedat Dilek wrote: > > > > > > > > > > OK, I see. > > > > > So I misunderstood the -o option. > > > > > > > > It was clearly documented in the man page: > > > > > > > > -o output_file > > > > Write the list of bad blocks to the specified file. > > > > Without this option, badblocks displays the list on > > > > its standard output. The format of this file is > > > > suitable for use by the -l option in e2fsck(8) or > > > > mke2fs(8). > > > > > > > > > > RTFM. > > > > > > > I will say that for modern disks, the usefulness of badblocks has > > > > decreased significantly over time. That's because for modern-sized > > > > disks, it can often take more than 24 hours to do a full read on the > > > > entire disk surface --- and the factory testing done by HDD > > > > manufacturers is far more comprehensive. > > > > > > > > In addition, SMART (see the smartctl package) is a much more reliable > > > > and efficient way of judging disk health. > > > > > > > > The badblocks program was written over two decades ago, before the > > > > days of SATA, and even IDE disks, when disk controlls and HDD's were > > > > far more primitive. These days, modern HDD and SSD will do their own > > > > bad block redirection from a built-in bad block sparing pool, and the > > > > usefulness of using badblocks has been significantly decreased. > > > > > > > > > > Thanks for the clarification on badblocks usage and usefulness. > > > > > > OK, I ran before badblocks: > > > > > > 1. smartctl -a /dev/sdc (shell) > > > 2. gsmartcontrol (GUI) > > > > > > The results showed me "this disk is healthy". > > > As you said: Both gave a very quick overview. > > > > > > - Sedat - > > > > Just note that not even the device firmware can't really know whether the > > block is good/bad unless it tries to read/write it. In that way I still > > find the badblocks useful because it can "force" the device to notice > > that there is something wrong and try to fix it (perhaps by remapping > > the bad block to spare one). Of course you could use dd for that, but > > there are several reasons why badblocks is still more convenient tool to > > do that. > > > > That said you should also check the SMART data _after_ you run the > > badblocks to see if it encountered any read errors and/or remapped some > > blocks. > > > > Thanks Lukas. > > With gsmartcontrol I archived two logs. > > The diff says: > > cd ~/DISK-HEALTH/gsmartcontrol > > git diff ST1000LM024_HN-M101MBB_S2U5J9CCB68827_2020-05-28.txt > ST1000LM024_HN-M101MBB_S2U5J9CCB68827_2021-03-05.txt | egrep -i ' > read|remap' | grep -i error > - 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 0 > + 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 2 > > There are no "remap" keywords in the gsmartcontrol log-files. Hi, yes, sorry I was not sure what the exact term the SMART is using so I remapping "remapping" in a descriptive sense. Looking at your output the field you're looking is "Reallocated_Event_Count" which is 0 in both cases. -Lukas > > I have attached both log-files. > ( Hope there is no sensitive data included. ) > > - Sedat - > > > > > > > > > [1] https://superuser.com/questions/171195/how-to-check-the-health-of-a-hard-drive > > > > > > smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.7.0-rc7-4-amd64-clang] (local build) > Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org > > === START OF INFORMATION SECTION === > Model Family: Seagate Samsung SpinPoint M8 (AF) > Device Model: ST1000LM024 HN-M101MBB > Serial Number: S2U5J9CCB68827 > LU WWN Device Id: 5 0004cf 208db3445 > Firmware Version: 2AR10001 > User Capacity: 1,000,204,886,016 bytes [1.00 TB] > Sector Sizes: 512 bytes logical, 4096 bytes physical > Rotation Rate: 5400 rpm > Form Factor: 2.5 inches > Device is: In smartctl database [for details use: -P show] > ATA Version is: ATA8-ACS T13/1699-D revision 6 > SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s) > Local Time is: Thu May 28 22:09:29 2020 CEST > SMART support is: Available - device has SMART capability. > SMART support is: Enabled > AAM feature is: Unavailable > APM level is: 254 (maximum performance) > Rd look-ahead is: Enabled > Write cache is: Enabled > DSN feature is: Unavailable > ATA Security is: Disabled, NOT FROZEN [SEC1] > > === START OF READ SMART DATA SECTION === > SMART overall-health self-assessment test result: PASSED > > General SMART Values: > Offline data collection status: (0x00) Offline data collection activity > was never started. > Auto Offline Data Collection: Disabled. > Self-test execution status: ( 0) The previous self-test routine completed > without error or no self-test has ever > been run. > Total time to complete Offline > data collection: (13380) seconds. > Offline data collection > capabilities: (0x5b) SMART execute Offline immediate. > Auto Offline data collection on/off support. > Suspend Offline collection upon new > command. > Offline surface scan supported. > Self-test supported. > No Conveyance Self-test supported. > Selective Self-test supported. > SMART capabilities: (0x0003) Saves SMART data before entering > power-saving mode. > Supports SMART auto save timer. > Error logging capability: (0x01) Error logging supported. > General Purpose Logging supported. > Short self-test routine > recommended polling time: ( 2) minutes. > Extended self-test routine > recommended polling time: ( 223) minutes. > SCT capabilities: (0x003f) SCT Status supported. > SCT Error Recovery Control supported. > SCT Feature Control supported. > SCT Data Table supported. > > SMART Attributes Data Structure revision number: 16 > Vendor Specific SMART Attributes with Thresholds: > ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE > 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 0 > 2 Throughput_Performance -OS--K 252 252 000 - 0 > 3 Spin_Up_Time PO---K 089 089 025 - 3463 > 4 Start_Stop_Count -O--CK 098 098 000 - 2129 > 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 > 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 > 8 Seek_Time_Performance --S--K 252 252 015 - 0 > 9 Power_On_Hours -O--CK 100 100 000 - 1289 > 10 Spin_Retry_Count -O--CK 252 252 051 - 0 > 11 Calibration_Retry_Count -O--CK 100 100 000 - 38 > 12 Power_Cycle_Count -O--CK 099 099 000 - 1421 > 191 G-Sense_Error_Rate -O---K 252 252 000 - 0 > 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 > 194 Temperature_Celsius -O---- 061 052 000 - 39 (Min/Max 13/49) > 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 > 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 > 197 Current_Pending_Sector -O--CK 252 252 000 - 0 > 198 Offline_Uncorrectable ----CK 252 252 000 - 0 > 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 > 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 2970 > 223 Load_Retry_Count -O--CK 100 100 000 - 38 > 225 Load_Cycle_Count -O--CK 098 098 000 - 22549 > ||||||_ K auto-keep > |||||__ C event count > ||||___ R error rate > |||____ S speed/performance > ||_____ O updated online > |______ P prefailure warning > > General Purpose Log Directory Version 1 > SMART Log Directory Version 1 [multi-sector log support] > Address Access R/W Size Description > 0x00 GPL,SL R/O 1 Log Directory > 0x01 SL R/O 1 Summary SMART error log > 0x02 SL R/O 2 Comprehensive SMART error log > 0x03 GPL R/O 2 Ext. Comprehensive SMART error log > 0x06 SL R/O 1 SMART self-test log > 0x07 GPL R/O 2 Extended self-test log > 0x08 GPL R/O 2 Power Conditions log > 0x09 SL R/W 1 Selective self-test log > 0x10 GPL R/O 1 NCQ Command Error log > 0x11 GPL R/O 1 SATA Phy Event Counters log > 0x80-0x9f GPL,SL R/W 16 Host vendor specific log > 0xc0-0xdf GPL,SL VS 16 Device vendor specific log > 0xe0 GPL,SL R/W 1 SCT Command/Status > 0xe1 GPL,SL R/W 1 SCT Data Transfer > > SMART Extended Comprehensive Error Log Version: 1 (2 sectors) > No Errors Logged > > SMART Extended Self-test Log Version: 1 (2 sectors) > Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error > # 1 Short offline Completed without error 00% 1289 - > > SMART Selective self-test log data structure revision number 0 > Note: revision number not 1 implies that no selective self-test has ever been run > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS > 1 0 0 Completed [00% left] (0-65535) > 2 0 0 Not_testing > 3 0 0 Not_testing > 4 0 0 Not_testing > 5 0 0 Not_testing > Selective self-test flags (0x0): > After scanning selected spans, do NOT read-scan remainder of disk. > If Selective self-test is pending on power-up, resume after 0 minute delay. > > SCT Status Version: 2 > SCT Version (vendor specific): 256 (0x0100) > Device State: Active (0) > Current Temperature: 39 Celsius > Power Cycle Min/Max Temperature: 37/41 Celsius > Lifetime Min/Max Temperature: 13/49 Celsius > Specified Max Operating Temperature: 80 Celsius > Under/Over Temperature Limit Count: 0/0 > > SCT Temperature History Version: 2 > Temperature Sampling Period: 5 minutes > Temperature Logging Interval: 5 minutes > Min/Max recommended Temperature: -5/80 Celsius > Min/Max Temperature Limit: -10/85 Celsius > Temperature History Size (Index): 128 (71) > > Index Estimated Time Temperature Celsius > 72 2020-05-28 11:30 39 ******************** > 73 2020-05-28 11:35 33 ************** > 74 2020-05-28 11:40 34 *************** > ... ..( 2 skipped). .. *************** > 77 2020-05-28 11:55 34 *************** > 78 2020-05-28 12:00 35 **************** > ... ..( 2 skipped). .. **************** > 81 2020-05-28 12:15 35 **************** > 82 2020-05-28 12:20 36 ***************** > 83 2020-05-28 12:25 37 ****************** > ... ..( 5 skipped). .. ****************** > 89 2020-05-28 12:55 37 ****************** > 90 2020-05-28 13:00 38 ******************* > ... ..( 10 skipped). .. ******************* > 101 2020-05-28 13:55 38 ******************* > 102 2020-05-28 14:00 39 ******************** > 103 2020-05-28 14:05 38 ******************* > ... ..( 2 skipped). .. ******************* > 106 2020-05-28 14:20 38 ******************* > 107 2020-05-28 14:25 39 ******************** > ... ..( 20 skipped). .. ******************** > 0 2020-05-28 16:10 39 ******************** > 1 2020-05-28 16:15 40 ********************* > ... ..( 11 skipped). .. ********************* > 13 2020-05-28 17:15 40 ********************* > 14 2020-05-28 17:20 41 ********************** > 15 2020-05-28 17:25 41 ********************** > 16 2020-05-28 17:30 41 ********************** > 17 2020-05-28 17:35 40 ********************* > 18 2020-05-28 17:40 40 ********************* > 19 2020-05-28 17:45 40 ********************* > 20 2020-05-28 17:50 42 *********************** > 21 2020-05-28 17:55 43 ************************ > 22 2020-05-28 18:00 42 *********************** > 23 2020-05-28 18:05 41 ********************** > 24 2020-05-28 18:10 40 ********************* > 25 2020-05-28 18:15 40 ********************* > 26 2020-05-28 18:20 40 ********************* > 27 2020-05-28 18:25 42 *********************** > 28 2020-05-28 18:30 43 ************************ > 29 2020-05-28 18:35 42 *********************** > 30 2020-05-28 18:40 41 ********************** > 31 2020-05-28 18:45 40 ********************* > 32 2020-05-28 18:50 39 ******************** > 33 2020-05-28 18:55 39 ******************** > 34 2020-05-28 19:00 39 ******************** > 35 2020-05-28 19:05 38 ******************* > ... ..( 5 skipped). .. ******************* > 41 2020-05-28 19:35 38 ******************* > 42 2020-05-28 19:40 39 ******************** > 43 2020-05-28 19:45 39 ******************** > 44 2020-05-28 19:50 40 ********************* > 45 2020-05-28 19:55 42 *********************** > 46 2020-05-28 20:00 41 ********************** > 47 2020-05-28 20:05 40 ********************* > 48 2020-05-28 20:10 39 ******************** > 49 2020-05-28 20:15 39 ******************** > 50 2020-05-28 20:20 38 ******************* > 51 2020-05-28 20:25 38 ******************* > 52 2020-05-28 20:30 38 ******************* > 53 2020-05-28 20:35 37 ****************** > ... ..( 2 skipped). .. ****************** > 56 2020-05-28 20:50 37 ****************** > 57 2020-05-28 20:55 38 ******************* > 58 2020-05-28 21:00 37 ****************** > ... ..( 2 skipped). .. ****************** > 61 2020-05-28 21:15 37 ****************** > 62 2020-05-28 21:20 39 ******************** > 63 2020-05-28 21:25 39 ******************** > 64 2020-05-28 21:30 40 ********************* > 65 2020-05-28 21:35 41 ********************** > 66 2020-05-28 21:40 41 ********************** > 67 2020-05-28 21:45 40 ********************* > 68 2020-05-28 21:50 40 ********************* > 69 2020-05-28 21:55 40 ********************* > 70 2020-05-28 22:00 39 ******************** > 71 2020-05-28 22:05 39 ******************** > > SCT Error Recovery Control: > Read: Disabled > Write: Disabled > > Device Statistics (GP/SMART Log 0x04) not supported > > SATA Phy Event Counters (GP Log 0x11) > ID Size Value Description > 0x0001 4 0 Command failed due to ICRC error > 0x0002 4 0 R_ERR response for data FIS > 0x0003 4 0 R_ERR response for device-to-host data FIS > 0x0004 4 0 R_ERR response for host-to-device data FIS > 0x0005 4 0 R_ERR response for non-data FIS > 0x0006 4 0 R_ERR response for device-to-host non-data FIS > 0x0007 4 0 R_ERR response for host-to-device non-data FIS > 0x0008 4 0 Device-to-host non-data FIS retries > 0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy > 0x000a 4 0 Device-to-host register FISes sent due to a COMRESET > 0x000b 4 0 CRC errors within host-to-device FIS > 0x000d 4 0 Non-CRC errors within host-to-device FIS > 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC > 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC > 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC > 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC > 0x8e00 4 0 Vendor specific > 0x8e01 4 0 Vendor specific > 0x8e02 4 0 Vendor specific > 0x8e03 4 0 Vendor specific > 0x8e04 4 0 Vendor specific > 0x8e05 4 0 Vendor specific > 0x8e06 4 0 Vendor specific > 0x8e07 4 0 Vendor specific > 0x8e08 4 0 Vendor specific > 0x8e09 4 0 Vendor specific > 0x8e0a 4 0 Vendor specific > 0x8e0b 4 0 Vendor specific > 0x8e0c 4 0 Vendor specific > 0x8e0d 4 0 Vendor specific > 0x8e0e 4 0 Vendor specific > 0x8e0f 4 0 Vendor specific > 0x8e10 4 0 Vendor specific > 0x8e11 4 0 Vendor specific > smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.12.0-rc1-11-amd64-clang13-cfi] (local build) > Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org > > === START OF INFORMATION SECTION === > Model Family: Seagate Samsung SpinPoint M8 (AF) > Device Model: ST1000LM024 HN-M101MBB > Serial Number: S2U5J9CCB68827 > LU WWN Device Id: 5 0004cf 208db3445 > Firmware Version: 2AR10001 > User Capacity: 1,000,204,886,016 bytes [1.00 TB] > Sector Sizes: 512 bytes logical, 4096 bytes physical > Rotation Rate: 5400 rpm > Form Factor: 2.5 inches > Device is: In smartctl database [for details use: -P show] > ATA Version is: ATA8-ACS T13/1699-D revision 6 > SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s) > Local Time is: Fri Mar 5 13:16:48 2021 CET > SMART support is: Available - device has SMART capability. > SMART support is: Enabled > AAM feature is: Unavailable > APM level is: 254 (maximum performance) > Rd look-ahead is: Enabled > Write cache is: Enabled > DSN feature is: Unavailable > ATA Security is: Disabled, NOT FROZEN [SEC1] > > === START OF READ SMART DATA SECTION === > SMART overall-health self-assessment test result: PASSED > > General SMART Values: > Offline data collection status: (0x00) Offline data collection activity > was never started. > Auto Offline Data Collection: Disabled. > Self-test execution status: ( 0) The previous self-test routine completed > without error or no self-test has ever > been run. > Total time to complete Offline > data collection: (13380) seconds. > Offline data collection > capabilities: (0x5b) SMART execute Offline immediate. > Auto Offline data collection on/off support. > Suspend Offline collection upon new > command. > Offline surface scan supported. > Self-test supported. > No Conveyance Self-test supported. > Selective Self-test supported. > SMART capabilities: (0x0003) Saves SMART data before entering > power-saving mode. > Supports SMART auto save timer. > Error logging capability: (0x01) Error logging supported. > General Purpose Logging supported. > Short self-test routine > recommended polling time: ( 2) minutes. > Extended self-test routine > recommended polling time: ( 223) minutes. > SCT capabilities: (0x003f) SCT Status supported. > SCT Error Recovery Control supported. > SCT Feature Control supported. > SCT Data Table supported. > > SMART Attributes Data Structure revision number: 16 > Vendor Specific SMART Attributes with Thresholds: > ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE > 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 2 > 2 Throughput_Performance -OS--K 252 252 000 - 0 > 3 Spin_Up_Time PO---K 089 089 025 - 3456 > 4 Start_Stop_Count -O--CK 098 098 000 - 2543 > 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 > 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 > 8 Seek_Time_Performance --S--K 252 252 015 - 0 > 9 Power_On_Hours -O--CK 100 100 000 - 4201 > 10 Spin_Retry_Count -O--CK 252 252 051 - 0 > 11 Calibration_Retry_Count -O--CK 100 100 000 - 244 > 12 Power_Cycle_Count -O--CK 099 099 000 - 1864 > 191 G-Sense_Error_Rate -O---K 252 252 000 - 0 > 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 > 194 Temperature_Celsius -O---- 064 049 000 - 35 (Min/Max 13/52) > 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 > 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 > 197 Current_Pending_Sector -O--CK 252 252 000 - 0 > 198 Offline_Uncorrectable ----CK 252 252 000 - 0 > 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 > 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 15982 > 223 Load_Retry_Count -O--CK 100 100 000 - 244 > 225 Load_Cycle_Count -O--CK 098 098 000 - 23647 > ||||||_ K auto-keep > |||||__ C event count > ||||___ R error rate > |||____ S speed/performance > ||_____ O updated online > |______ P prefailure warning > > General Purpose Log Directory Version 1 > SMART Log Directory Version 1 [multi-sector log support] > Address Access R/W Size Description > 0x00 GPL,SL R/O 1 Log Directory > 0x01 SL R/O 1 Summary SMART error log > 0x02 SL R/O 2 Comprehensive SMART error log > 0x03 GPL R/O 2 Ext. Comprehensive SMART error log > 0x06 SL R/O 1 SMART self-test log > 0x07 GPL R/O 2 Extended self-test log > 0x08 GPL R/O 2 Power Conditions log > 0x09 SL R/W 1 Selective self-test log > 0x10 GPL R/O 1 NCQ Command Error log > 0x11 GPL R/O 1 SATA Phy Event Counters log > 0x80-0x9f GPL,SL R/W 16 Host vendor specific log > 0xc0-0xdf GPL,SL VS 16 Device vendor specific log > 0xe0 GPL,SL R/W 1 SCT Command/Status > 0xe1 GPL,SL R/W 1 SCT Data Transfer > > SMART Extended Comprehensive Error Log Version: 1 (2 sectors) > No Errors Logged > > SMART Extended Self-test Log Version: 1 (2 sectors) > Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error > # 1 Short offline Completed without error 00% 1289 - > > SMART Selective self-test log data structure revision number 0 > Note: revision number not 1 implies that no selective self-test has ever been run > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS > 1 0 0 Completed [00% left] (0-65535) > 2 0 0 Not_testing > 3 0 0 Not_testing > 4 0 0 Not_testing > 5 0 0 Not_testing > Selective self-test flags (0x0): > After scanning selected spans, do NOT read-scan remainder of disk. > If Selective self-test is pending on power-up, resume after 0 minute delay. > > SCT Status Version: 2 > SCT Version (vendor specific): 256 (0x0100) > Device State: Active (0) > Current Temperature: 35 Celsius > Power Cycle Min/Max Temperature: 26/42 Celsius > Lifetime Min/Max Temperature: 13/51 Celsius > Specified Max Operating Temperature: 80 Celsius > Under/Over Temperature Limit Count: 0/0 > > SCT Temperature History Version: 2 > Temperature Sampling Period: 5 minutes > Temperature Logging Interval: 5 minutes > Min/Max recommended Temperature: -5/80 Celsius > Min/Max Temperature Limit: -10/85 Celsius > Temperature History Size (Index): 128 (121) > > Index Estimated Time Temperature Celsius > 122 2021-03-05 02:40 35 **************** > ... ..( 2 skipped). .. **************** > 125 2021-03-05 02:55 35 **************** > 126 2021-03-05 03:00 34 *************** > ... ..( 3 skipped). .. *************** > 2 2021-03-05 03:20 34 *************** > 3 2021-03-05 03:25 35 **************** > 4 2021-03-05 03:30 35 **************** > 5 2021-03-05 03:35 34 *************** > ... ..( 17 skipped). .. *************** > 23 2021-03-05 05:05 34 *************** > 24 2021-03-05 05:10 33 ************** > 25 2021-03-05 05:15 33 ************** > 26 2021-03-05 05:20 34 *************** > 27 2021-03-05 05:25 33 ************** > 28 2021-03-05 05:30 34 *************** > ... ..( 4 skipped). .. *************** > 33 2021-03-05 05:55 34 *************** > 34 2021-03-05 06:00 33 ************** > ... ..( 2 skipped). .. ************** > 37 2021-03-05 06:15 33 ************** > 38 2021-03-05 06:20 34 *************** > 39 2021-03-05 06:25 35 **************** > 40 2021-03-05 06:30 35 **************** > 41 2021-03-05 06:35 35 **************** > 42 2021-03-05 06:40 34 *************** > 43 2021-03-05 06:45 34 *************** > 44 2021-03-05 06:50 34 *************** > 45 2021-03-05 06:55 33 ************** > 46 2021-03-05 07:00 33 ************** > 47 2021-03-05 07:05 33 ************** > 48 2021-03-05 07:10 34 *************** > ... ..( 3 skipped). .. *************** > 52 2021-03-05 07:30 34 *************** > 53 2021-03-05 07:35 35 **************** > 54 2021-03-05 07:40 35 **************** > 55 2021-03-05 07:45 35 **************** > 56 2021-03-05 07:50 36 ***************** > 57 2021-03-05 07:55 35 **************** > ... ..( 13 skipped). .. **************** > 71 2021-03-05 09:05 35 **************** > 72 2021-03-05 09:10 36 ***************** > ... ..( 13 skipped). .. ***************** > 86 2021-03-05 10:20 36 ***************** > 87 2021-03-05 10:25 37 ****************** > 88 2021-03-05 10:30 38 ******************* > 89 2021-03-05 10:35 38 ******************* > 90 2021-03-05 10:40 39 ******************** > 91 2021-03-05 10:45 39 ******************** > 92 2021-03-05 10:50 39 ******************** > 93 2021-03-05 10:55 38 ******************* > 94 2021-03-05 11:00 37 ****************** > 95 2021-03-05 11:05 37 ****************** > 96 2021-03-05 11:10 39 ******************** > 97 2021-03-05 11:15 41 ********************** > 98 2021-03-05 11:20 42 *********************** > 99 2021-03-05 11:25 42 *********************** > 100 2021-03-05 11:30 40 ********************* > 101 2021-03-05 11:35 39 ******************** > 102 2021-03-05 11:40 38 ******************* > 103 2021-03-05 11:45 37 ****************** > ... ..( 3 skipped). .. ****************** > 107 2021-03-05 12:05 37 ****************** > 108 2021-03-05 12:10 39 ******************** > 109 2021-03-05 12:15 39 ******************** > 110 2021-03-05 12:20 37 ****************** > ... ..( 2 skipped). .. ****************** > 113 2021-03-05 12:35 37 ****************** > 114 2021-03-05 12:40 38 ******************* > 115 2021-03-05 12:45 37 ****************** > 116 2021-03-05 12:50 37 ****************** > 117 2021-03-05 12:55 36 ***************** > ... ..( 2 skipped). .. ***************** > 120 2021-03-05 13:10 36 ***************** > 121 2021-03-05 13:15 35 **************** > > SCT Error Recovery Control: > Read: Disabled > Write: Disabled > > Device Statistics (GP/SMART Log 0x04) not supported > > SATA Phy Event Counters (GP Log 0x11) > ID Size Value Description > 0x0001 4 0 Command failed due to ICRC error > 0x0002 4 0 R_ERR response for data FIS > 0x0003 4 0 R_ERR response for device-to-host data FIS > 0x0004 4 0 R_ERR response for host-to-device data FIS > 0x0005 4 0 R_ERR response for non-data FIS > 0x0006 4 0 R_ERR response for device-to-host non-data FIS > 0x0007 4 0 R_ERR response for host-to-device non-data FIS > 0x0008 4 0 Device-to-host non-data FIS retries > 0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy > 0x000a 4 0 Device-to-host register FISes sent due to a COMRESET > 0x000b 4 0 CRC errors within host-to-device FIS > 0x000d 4 0 Non-CRC errors within host-to-device FIS > 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC > 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC > 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC > 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC > 0x8e00 4 0 Vendor specific > 0x8e01 4 0 Vendor specific > 0x8e02 4 0 Vendor specific > 0x8e03 4 0 Vendor specific > 0x8e04 4 0 Vendor specific > 0x8e05 4 0 Vendor specific > 0x8e06 4 0 Vendor specific > 0x8e07 4 0 Vendor specific > 0x8e08 4 0 Vendor specific > 0x8e09 4 0 Vendor specific > 0x8e0a 4 0 Vendor specific > 0x8e0b 4 0 Vendor specific > 0x8e0c 4 0 Vendor specific > 0x8e0d 4 0 Vendor specific > 0x8e0e 4 0 Vendor specific > 0x8e0f 4 0 Vendor specific > 0x8e10 4 0 Vendor specific > 0x8e11 4 0 Vendor specific
