On Fri, Mar 5, 2021 at 1:00 PM Lukas Czerner <lczerner@xxxxxxxxxx> wrote:
>
> On Mon, Mar 01, 2021 at 04:42:26PM +0100, Sedat Dilek wrote:
> > On Mon, Mar 1, 2021 at 4:34 PM Theodore Ts'o <tytso@xxxxxxx> wrote:
> > >
> > > On Mon, Mar 01, 2021 at 04:12:03PM +0100, Sedat Dilek wrote:
> > > >
> > > > OK, I see.
> > > > So I misunderstood the -o option.
> > >
> > > It was clearly documented in the man page:
> > >
> > > -o output_file
> > > Write the list of bad blocks to the specified file.
> > > Without this option, badblocks displays the list on
> > > its standard output. The format of this file is
> > > suitable for use by the -l option in e2fsck(8) or
> > > mke2fs(8).
> > >
> >
> > RTFM.
> >
> > > I will say that for modern disks, the usefulness of badblocks has
> > > decreased significantly over time. That's because for modern-sized
> > > disks, it can often take more than 24 hours to do a full read on the
> > > entire disk surface --- and the factory testing done by HDD
> > > manufacturers is far more comprehensive.
> > >
> > > In addition, SMART (see the smartctl package) is a much more reliable
> > > and efficient way of judging disk health.
> > >
> > > The badblocks program was written over two decades ago, before the
> > > days of SATA, and even IDE disks, when disk controlls and HDD's were
> > > far more primitive. These days, modern HDD and SSD will do their own
> > > bad block redirection from a built-in bad block sparing pool, and the
> > > usefulness of using badblocks has been significantly decreased.
> > >
> >
> > Thanks for the clarification on badblocks usage and usefulness.
> >
> > OK, I ran before badblocks:
> >
> > 1. smartctl -a /dev/sdc (shell)
> > 2. gsmartcontrol (GUI)
> >
> > The results showed me "this disk is healthy".
> > As you said: Both gave a very quick overview.
> >
> > - Sedat -
>
> Just note that not even the device firmware can't really know whether the
> block is good/bad unless it tries to read/write it. In that way I still
> find the badblocks useful because it can "force" the device to notice
> that there is something wrong and try to fix it (perhaps by remapping
> the bad block to spare one). Of course you could use dd for that, but
> there are several reasons why badblocks is still more convenient tool to
> do that.
>
> That said you should also check the SMART data _after_ you run the
> badblocks to see if it encountered any read errors and/or remapped some
> blocks.
>
Thanks Lukas.
With gsmartcontrol I archived two logs.
The diff says:
cd ~/DISK-HEALTH/gsmartcontrol
git diff ST1000LM024_HN-M101MBB_S2U5J9CCB68827_2020-05-28.txt
ST1000LM024_HN-M101MBB_S2U5J9CCB68827_2021-03-05.txt | egrep -i '
read|remap' | grep -i error
- 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 0
+ 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 2
There are no "remap" keywords in the gsmartcontrol log-files.
I have attached both log-files.
( Hope there is no sensitive data included. )
- Sedat -
>
> >
> > [1] https://superuser.com/questions/171195/how-to-check-the-health-of-a-hard-drive
> >
>
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.7.0-rc7-4-amd64-clang] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Samsung SpinPoint M8 (AF)
Device Model: ST1000LM024 HN-M101MBB
Serial Number: S2U5J9CCB68827
LU WWN Device Id: 5 0004cf 208db3445
Firmware Version: 2AR10001
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Thu May 28 22:09:29 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, NOT FROZEN [SEC1]
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (13380) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 223) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 100 100 051 - 0
2 Throughput_Performance -OS--K 252 252 000 - 0
3 Spin_Up_Time PO---K 089 089 025 - 3463
4 Start_Stop_Count -O--CK 098 098 000 - 2129
5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0
7 Seek_Error_Rate -OSR-K 252 252 051 - 0
8 Seek_Time_Performance --S--K 252 252 015 - 0
9 Power_On_Hours -O--CK 100 100 000 - 1289
10 Spin_Retry_Count -O--CK 252 252 051 - 0
11 Calibration_Retry_Count -O--CK 100 100 000 - 38
12 Power_Cycle_Count -O--CK 099 099 000 - 1421
191 G-Sense_Error_Rate -O---K 252 252 000 - 0
192 Power-Off_Retract_Count -O---K 252 252 000 - 0
194 Temperature_Celsius -O---- 061 052 000 - 39 (Min/Max 13/49)
195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0
196 Reallocated_Event_Count -O--CK 252 252 000 - 0
197 Current_Pending_Sector -O--CK 252 252 000 - 0
198 Offline_Uncorrectable ----CK 252 252 000 - 0
199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0
200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 2970
223 Load_Retry_Count -O--CK 100 100 000 - 38
225 Load_Cycle_Count -O--CK 098 098 000 - 22549
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 2 Comprehensive SMART error log
0x03 GPL R/O 2 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 2 Extended self-test log
0x08 GPL R/O 2 Power Conditions log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xc0-0xdf GPL,SL VS 16 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (2 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1289 -
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 256 (0x0100)
Device State: Active (0)
Current Temperature: 39 Celsius
Power Cycle Min/Max Temperature: 37/41 Celsius
Lifetime Min/Max Temperature: 13/49 Celsius
Specified Max Operating Temperature: 80 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 5 minutes
Temperature Logging Interval: 5 minutes
Min/Max recommended Temperature: -5/80 Celsius
Min/Max Temperature Limit: -10/85 Celsius
Temperature History Size (Index): 128 (71)
Index Estimated Time Temperature Celsius
72 2020-05-28 11:30 39 ********************
73 2020-05-28 11:35 33 **************
74 2020-05-28 11:40 34 ***************
... ..( 2 skipped). .. ***************
77 2020-05-28 11:55 34 ***************
78 2020-05-28 12:00 35 ****************
... ..( 2 skipped). .. ****************
81 2020-05-28 12:15 35 ****************
82 2020-05-28 12:20 36 *****************
83 2020-05-28 12:25 37 ******************
... ..( 5 skipped). .. ******************
89 2020-05-28 12:55 37 ******************
90 2020-05-28 13:00 38 *******************
... ..( 10 skipped). .. *******************
101 2020-05-28 13:55 38 *******************
102 2020-05-28 14:00 39 ********************
103 2020-05-28 14:05 38 *******************
... ..( 2 skipped). .. *******************
106 2020-05-28 14:20 38 *******************
107 2020-05-28 14:25 39 ********************
... ..( 20 skipped). .. ********************
0 2020-05-28 16:10 39 ********************
1 2020-05-28 16:15 40 *********************
... ..( 11 skipped). .. *********************
13 2020-05-28 17:15 40 *********************
14 2020-05-28 17:20 41 **********************
15 2020-05-28 17:25 41 **********************
16 2020-05-28 17:30 41 **********************
17 2020-05-28 17:35 40 *********************
18 2020-05-28 17:40 40 *********************
19 2020-05-28 17:45 40 *********************
20 2020-05-28 17:50 42 ***********************
21 2020-05-28 17:55 43 ************************
22 2020-05-28 18:00 42 ***********************
23 2020-05-28 18:05 41 **********************
24 2020-05-28 18:10 40 *********************
25 2020-05-28 18:15 40 *********************
26 2020-05-28 18:20 40 *********************
27 2020-05-28 18:25 42 ***********************
28 2020-05-28 18:30 43 ************************
29 2020-05-28 18:35 42 ***********************
30 2020-05-28 18:40 41 **********************
31 2020-05-28 18:45 40 *********************
32 2020-05-28 18:50 39 ********************
33 2020-05-28 18:55 39 ********************
34 2020-05-28 19:00 39 ********************
35 2020-05-28 19:05 38 *******************
... ..( 5 skipped). .. *******************
41 2020-05-28 19:35 38 *******************
42 2020-05-28 19:40 39 ********************
43 2020-05-28 19:45 39 ********************
44 2020-05-28 19:50 40 *********************
45 2020-05-28 19:55 42 ***********************
46 2020-05-28 20:00 41 **********************
47 2020-05-28 20:05 40 *********************
48 2020-05-28 20:10 39 ********************
49 2020-05-28 20:15 39 ********************
50 2020-05-28 20:20 38 *******************
51 2020-05-28 20:25 38 *******************
52 2020-05-28 20:30 38 *******************
53 2020-05-28 20:35 37 ******************
... ..( 2 skipped). .. ******************
56 2020-05-28 20:50 37 ******************
57 2020-05-28 20:55 38 *******************
58 2020-05-28 21:00 37 ******************
... ..( 2 skipped). .. ******************
61 2020-05-28 21:15 37 ******************
62 2020-05-28 21:20 39 ********************
63 2020-05-28 21:25 39 ********************
64 2020-05-28 21:30 40 *********************
65 2020-05-28 21:35 41 **********************
66 2020-05-28 21:40 41 **********************
67 2020-05-28 21:45 40 *********************
68 2020-05-28 21:50 40 *********************
69 2020-05-28 21:55 40 *********************
70 2020-05-28 22:00 39 ********************
71 2020-05-28 22:05 39 ********************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0003 4 0 R_ERR response for device-to-host data FIS
0x0004 4 0 R_ERR response for host-to-device data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x0006 4 0 R_ERR response for device-to-host non-data FIS
0x0007 4 0 R_ERR response for host-to-device non-data FIS
0x0008 4 0 Device-to-host non-data FIS retries
0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 0 Device-to-host register FISes sent due to a COMRESET
0x000b 4 0 CRC errors within host-to-device FIS
0x000d 4 0 Non-CRC errors within host-to-device FIS
0x000f 4 0 R_ERR response for host-to-device data FIS, CRC
0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC
0x8e00 4 0 Vendor specific
0x8e01 4 0 Vendor specific
0x8e02 4 0 Vendor specific
0x8e03 4 0 Vendor specific
0x8e04 4 0 Vendor specific
0x8e05 4 0 Vendor specific
0x8e06 4 0 Vendor specific
0x8e07 4 0 Vendor specific
0x8e08 4 0 Vendor specific
0x8e09 4 0 Vendor specific
0x8e0a 4 0 Vendor specific
0x8e0b 4 0 Vendor specific
0x8e0c 4 0 Vendor specific
0x8e0d 4 0 Vendor specific
0x8e0e 4 0 Vendor specific
0x8e0f 4 0 Vendor specific
0x8e10 4 0 Vendor specific
0x8e11 4 0 Vendor specificsmartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.12.0-rc1-11-amd64-clang13-cfi] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Samsung SpinPoint M8 (AF)
Device Model: ST1000LM024 HN-M101MBB
Serial Number: S2U5J9CCB68827
LU WWN Device Id: 5 0004cf 208db3445
Firmware Version: 2AR10001
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Fri Mar 5 13:16:48 2021 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, NOT FROZEN [SEC1]
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (13380) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 223) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 100 100 051 - 2
2 Throughput_Performance -OS--K 252 252 000 - 0
3 Spin_Up_Time PO---K 089 089 025 - 3456
4 Start_Stop_Count -O--CK 098 098 000 - 2543
5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0
7 Seek_Error_Rate -OSR-K 252 252 051 - 0
8 Seek_Time_Performance --S--K 252 252 015 - 0
9 Power_On_Hours -O--CK 100 100 000 - 4201
10 Spin_Retry_Count -O--CK 252 252 051 - 0
11 Calibration_Retry_Count -O--CK 100 100 000 - 244
12 Power_Cycle_Count -O--CK 099 099 000 - 1864
191 G-Sense_Error_Rate -O---K 252 252 000 - 0
192 Power-Off_Retract_Count -O---K 252 252 000 - 0
194 Temperature_Celsius -O---- 064 049 000 - 35 (Min/Max 13/52)
195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0
196 Reallocated_Event_Count -O--CK 252 252 000 - 0
197 Current_Pending_Sector -O--CK 252 252 000 - 0
198 Offline_Uncorrectable ----CK 252 252 000 - 0
199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0
200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 15982
223 Load_Retry_Count -O--CK 100 100 000 - 244
225 Load_Cycle_Count -O--CK 098 098 000 - 23647
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 2 Comprehensive SMART error log
0x03 GPL R/O 2 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 2 Extended self-test log
0x08 GPL R/O 2 Power Conditions log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xc0-0xdf GPL,SL VS 16 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (2 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1289 -
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 256 (0x0100)
Device State: Active (0)
Current Temperature: 35 Celsius
Power Cycle Min/Max Temperature: 26/42 Celsius
Lifetime Min/Max Temperature: 13/51 Celsius
Specified Max Operating Temperature: 80 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 5 minutes
Temperature Logging Interval: 5 minutes
Min/Max recommended Temperature: -5/80 Celsius
Min/Max Temperature Limit: -10/85 Celsius
Temperature History Size (Index): 128 (121)
Index Estimated Time Temperature Celsius
122 2021-03-05 02:40 35 ****************
... ..( 2 skipped). .. ****************
125 2021-03-05 02:55 35 ****************
126 2021-03-05 03:00 34 ***************
... ..( 3 skipped). .. ***************
2 2021-03-05 03:20 34 ***************
3 2021-03-05 03:25 35 ****************
4 2021-03-05 03:30 35 ****************
5 2021-03-05 03:35 34 ***************
... ..( 17 skipped). .. ***************
23 2021-03-05 05:05 34 ***************
24 2021-03-05 05:10 33 **************
25 2021-03-05 05:15 33 **************
26 2021-03-05 05:20 34 ***************
27 2021-03-05 05:25 33 **************
28 2021-03-05 05:30 34 ***************
... ..( 4 skipped). .. ***************
33 2021-03-05 05:55 34 ***************
34 2021-03-05 06:00 33 **************
... ..( 2 skipped). .. **************
37 2021-03-05 06:15 33 **************
38 2021-03-05 06:20 34 ***************
39 2021-03-05 06:25 35 ****************
40 2021-03-05 06:30 35 ****************
41 2021-03-05 06:35 35 ****************
42 2021-03-05 06:40 34 ***************
43 2021-03-05 06:45 34 ***************
44 2021-03-05 06:50 34 ***************
45 2021-03-05 06:55 33 **************
46 2021-03-05 07:00 33 **************
47 2021-03-05 07:05 33 **************
48 2021-03-05 07:10 34 ***************
... ..( 3 skipped). .. ***************
52 2021-03-05 07:30 34 ***************
53 2021-03-05 07:35 35 ****************
54 2021-03-05 07:40 35 ****************
55 2021-03-05 07:45 35 ****************
56 2021-03-05 07:50 36 *****************
57 2021-03-05 07:55 35 ****************
... ..( 13 skipped). .. ****************
71 2021-03-05 09:05 35 ****************
72 2021-03-05 09:10 36 *****************
... ..( 13 skipped). .. *****************
86 2021-03-05 10:20 36 *****************
87 2021-03-05 10:25 37 ******************
88 2021-03-05 10:30 38 *******************
89 2021-03-05 10:35 38 *******************
90 2021-03-05 10:40 39 ********************
91 2021-03-05 10:45 39 ********************
92 2021-03-05 10:50 39 ********************
93 2021-03-05 10:55 38 *******************
94 2021-03-05 11:00 37 ******************
95 2021-03-05 11:05 37 ******************
96 2021-03-05 11:10 39 ********************
97 2021-03-05 11:15 41 **********************
98 2021-03-05 11:20 42 ***********************
99 2021-03-05 11:25 42 ***********************
100 2021-03-05 11:30 40 *********************
101 2021-03-05 11:35 39 ********************
102 2021-03-05 11:40 38 *******************
103 2021-03-05 11:45 37 ******************
... ..( 3 skipped). .. ******************
107 2021-03-05 12:05 37 ******************
108 2021-03-05 12:10 39 ********************
109 2021-03-05 12:15 39 ********************
110 2021-03-05 12:20 37 ******************
... ..( 2 skipped). .. ******************
113 2021-03-05 12:35 37 ******************
114 2021-03-05 12:40 38 *******************
115 2021-03-05 12:45 37 ******************
116 2021-03-05 12:50 37 ******************
117 2021-03-05 12:55 36 *****************
... ..( 2 skipped). .. *****************
120 2021-03-05 13:10 36 *****************
121 2021-03-05 13:15 35 ****************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0003 4 0 R_ERR response for device-to-host data FIS
0x0004 4 0 R_ERR response for host-to-device data FIS
0x0005 4 0 R_ERR response for non-data FIS
0x0006 4 0 R_ERR response for device-to-host non-data FIS
0x0007 4 0 R_ERR response for host-to-device non-data FIS
0x0008 4 0 Device-to-host non-data FIS retries
0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 0 Device-to-host register FISes sent due to a COMRESET
0x000b 4 0 CRC errors within host-to-device FIS
0x000d 4 0 Non-CRC errors within host-to-device FIS
0x000f 4 0 R_ERR response for host-to-device data FIS, CRC
0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC
0x8e00 4 0 Vendor specific
0x8e01 4 0 Vendor specific
0x8e02 4 0 Vendor specific
0x8e03 4 0 Vendor specific
0x8e04 4 0 Vendor specific
0x8e05 4 0 Vendor specific
0x8e06 4 0 Vendor specific
0x8e07 4 0 Vendor specific
0x8e08 4 0 Vendor specific
0x8e09 4 0 Vendor specific
0x8e0a 4 0 Vendor specific
0x8e0b 4 0 Vendor specific
0x8e0c 4 0 Vendor specific
0x8e0d 4 0 Vendor specific
0x8e0e 4 0 Vendor specific
0x8e0f 4 0 Vendor specific
0x8e10 4 0 Vendor specific
0x8e11 4 0 Vendor specific
