Antti Palosaari wrote: <snip> >> >> OK I have no firmware in /lib/firmware, it is all in the kernel >> directory. I have copied the file from the above URL which is the one >> I've been using and I still get "af9013: firmware version:4.73.0" in >> dmesg. Full 9015 relevant dmesg below. > > Is that possible that you are looking firmware file from wrong > directory? I mean that you have for example /lib/firmware/kernel-2.6.1/ > and /lib/firmware/kernel-2.6.2/ other having 4.73 and the other 4.95? > Remove all af9015 firmwares from kernel-x.x.x directories and leave > 4.95.0 to /lib/firmware/. Then take unplug stick and boot machine and > plug stick again. > > I see from dmesg log that firmware copy to 2nd frontend fails. This is > due to fact that currently driver has hard coded checksum for 4.95.0. I double checked the firmware and there was only one copy in /lib/firmware/kernel-blah It matched the 4.95.0 version. I did as mentioned earlier to boot without USB card plugged in, then plugged in device. It now looks better: [ 55.650921] usb 2-2: new high speed USB device using ehci_hcd and address 4 [ 55.703555] usb 2-2: configuration #1 chosen from 1 choice [ 55.706215] af9015_usb_probe: interface:0 [ 55.706814] af9015_identify_state: reply:01 [ 55.706816] dvb-usb: found a 'DigitalNow TinyTwin DVB-T Receiver' in cold state, will try to load a firmware [ 55.719697] dvb-usb: downloading firmware from file 'dvb-usb-af9015.fw' [ 55.719700] af9015_download_firmware: [ 55.752878] af9015_usb_probe: interface:1 [ 55.752920] usb 2-2: USB disconnect, address 4 [ 55.755152] dvb-usb: generic DVB-USB module successfully deinitialized and disconnected. [ 55.755185] dvb-usb: generic DVB-USB module successfully deinitialized and disconnected. [ 55.846024] usb 2-2: new high speed USB device using ehci_hcd and address 5 [ 55.898765] usb 2-2: configuration #1 chosen from 1 choice [ 55.899005] af9015_usb_probe: interface:0 [ 55.902273] af9015_identify_state: reply:02 [ 55.902276] dvb-usb: found a 'DigitalNow TinyTwin DVB-T Receiver' in warm state. [ 55.902566] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 55.903174] DVB: registering new adapter (DigitalNow TinyTwin DVB-T Receiver) [ 55.903288] af9015_eeprom_dump: [ 55.915696] 00: 2a 88 9b 0b 00 00 00 00 d3 13 26 32 00 02 01 02 [ 55.932201] 10: 03 80 00 fa fa 10 40 ef 01 30 31 30 31 30 39 31 [ 55.949854] 20: 34 30 36 30 30 30 30 31 ff ff ff ff ff ff ff ff [ 55.963675] 30: 00 01 3a 01 00 08 02 00 da 11 00 00 1e ff ff ff [ 55.978323] 40: ff ff ff ff ff 08 02 00 da 11 00 00 1e ff ff ff [ 55.997833] 50: ff ff ff ff ff 24 00 00 04 03 09 04 10 03 41 00 [ 56.014259] 60: 66 00 61 00 74 00 65 00 63 00 68 00 10 03 44 00 [ 56.034290] 70: 56 00 42 00 2d 00 54 00 20 00 32 00 20 03 30 00 [ 56.050029] 80: 31 00 30 00 31 00 30 00 31 00 30 00 31 00 30 00 [ 56.071905] 90: 36 00 30 00 30 00 30 00 30 00 31 00 00 ff ff ff [ 56.084186] a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 56.096469] b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 56.108748] c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 56.121032] d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 56.133313] e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 56.148280] f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 56.149075] af9015_read_config: TS mode:1 [ 56.149816] af9015_read_config: xtal:2 set adc_clock:28000 [ 56.151353] af9015_read_config: IF1:4570 [ 56.152885] af9015_read_config: MT2060 IF1:0 [ 56.153653] af9015_read_config: tuner id1:30 [ 56.154420] af9015_read_config: spectral inversion:0 [ 56.208057] af9013: firmware version:4.95.0 [ 56.219005] DVB: registering frontend 0 (Afatech AF9013 DVB-T)... [ 56.219030] af9015_tuner_attach: [ 56.282874] mxl500x_attach: Attaching ... [ 56.282877] mxl500x_attach: MXL500x tuner succesfully attached [ 56.282879] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 56.283100] DVB: registering new adapter (DigitalNow TinyTwin DVB-T Receiver) [ 56.283216] af9015_copy_firmware: [ 56.476723] af9015_copy_firmware: firmware copy done [ 56.517404] af9015_copy_firmware: firmware boot cmd status:0 [ 56.557320] af9015_copy_firmware: firmware status cmd status:0 fw status:0c [ 56.559620] af9013: firmware version:4.95.0 [ 56.567300] DVB: registering frontend 1 (Afatech AF9013 DVB-T)... [ 56.567322] af9015_tuner_attach: [ 56.567352] mxl500x_attach: Attaching ... [ 56.567353] mxl500x_attach: MXL500x tuner succesfully attached [ 56.567356] dvb-usb: DigitalNow TinyTwin DVB-T Receiver successfully initialized and connected. [ 56.567358] af9015_init: [ 56.567359] af9015_init_endpoint: USB speed:3 [ 56.591860] af9015_download_ir_table: [ 56.690500] input: Afatech DVB-T 2 as /devices/pci0000:00/0000:00:02.1/usb2/2-2/2-2:1.1/input/input6 [ 56.702667] input,hidraw2: USB HID v1.01 Keyboard [Afatech DVB-T 2] on usb-0000:00:02.1-2 [ 59.987029] eth0: no IPv6 routers present > >> I'm not sure it's a problem at this point as I've at least got TV but >> you may be interested from a developer point of view as there are a >> few errors in the dmesg. >> >> On a related note: What are the chances of getting the remote that >> came with the usb stick working? It's this one: >> http://www.digitalnow.com.au/images/ProRemote.jpg > > It should be polled. There is code for than in the driver already, but > it is disabled currently. Cool. So I guess it has at least been looked at then. Cheers Peter -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean. _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
