On Wed, 19 Mar 2008 03:18:32 +0900
timf <timf@xxxxxxxxxxxx> wrote:
> Hi Mauro,
>
> On Tue, 2008-03-18 at 10:30 -0300, Mauro Carvalho Chehab wrote:
> > On Sat, 15 Mar 2008 18:33:56 +0900
> > timf <timf@xxxxxxxxxxxx> wrote:
> >
> > > [ 15.000000] saa7133[0]: subsystem: 1461:f936, board: AVerMedia Hybrid
> > > TV/Radio (A16D) [card=137,autodetected]
> >
> >
> > > [ 15.296000] tuner' 2-0061: Setting mode_mask to 0x0e
> > > [ 15.296000] tuner' 2-0061: chip found @ 0xc2 (saa7133[0])
> > > [ 15.296000] tuner' 2-0061: tuner 0x61: Tuner type absent
> >
> > The above is not right. It should be using type=71 for the tuner.
> >
> > I think I found the bug: the tuner addresses should be set to ADDR_UNSET,
> > instead of keeping it blank.
> >
> > Please do an "hg pull -u" and try again, recompiling and re-installing the modules:
> > hg pull -u
> > make rmmod
> > make
> > make install
> > modprobe saa7134
> >
> > > 8) The chip on my card is xc3018. Why does module xc5000 load?
> >
> > This is an issue on the way cards are attached, at tuner_core. Since they
> > directly access xc5000 code, with:
> >
> > if (!xc5000_attach(&t->fe, t->i2c->adapter, &xc5000_cfg)) {
> >
> > xc5000 module will be loaded, even if not used. It shouldn't be hard to fix
> > this, by using the macro dvb_attach().
> >
> >
> >
> > Cheers,
> > Mauro
>
>
> 1) There is something wrong with the repo at present
> - it just times out and aborts.
>
> 2) So I copied the latest tip.tgz and extracted it.
> (Thus hg pull won't work - no .hg)
>
> 3) I tried to interpret your meaning and tried this in saa7134-cards.c
>
> },
> [SAA7134_BOARD_AVERMEDIA_A16D] = {
> .name = "AVerMedia Hybrid TV/Radio (A16D)",
> .audio_clock = 0x187de7,
> .tuner_type = TUNER_XC2028,
> .tuner_addr = ADDR_UNSET,
> .inputs = {{
> .name = name_tv,
> .vmux = 1,
> .amux = TV,
> .tv = 1,
> }, {
> .name = name_svideo,
> .vmux = 8,
> .amux = LINE1,
> } },
> .radio = {
> .name = name_radio,
> .amux = LINE1,
> },
> },
> [SAA7134_BOARD_AVERMEDIA_M115] = {
>
> 4) My options file:
>
> # Enable double-buffering so gstreamer et. al. work
> options quickcam compatible=2
>
> # Default hostap to managed mode
> options hostap_pci iw_mode=2
> options hostap_cs iw_mode=2
>
> options tuner-xc2028 debug=1
> options tuner debug=1
> options saa7134 i2c_scan=1
> # i2c_debug=1 ir_debug=1
>
> 5) However, with or without ".tuner_addr = ADDR_UNSET,"
> dmesg is the same - no tuner.
>
> <snip>
> [ 40.560890] ACPI: PCI Interrupt 0000:04:09.0[A] -> Link [APC2] -> GSI
> 17 (level, low) -> IRQ 17
> [ 40.560898] saa7133[0]: found at 0000:04:09.0, rev: 209, irq: 17,
> latency: 32, mmio: 0xfdbff000
> [ 40.560905] saa7133[0]: subsystem: 1461:f936, board: AVerMedia Hybrid
> TV/Radio (A16D) [card=137,autodetected]
> [ 40.560914] saa7133[0]: board init: gpio is 22000
> [ 40.561341] input: PC Speaker as /class/input/input4
> [ 40.727930] saa7133[0]: i2c eeprom 00: 61 14 36 f9 00 00 00 00 00 00
> 00 00 00 00 00 00
> [ 40.727939] saa7133[0]: i2c eeprom 10: ff ff ff ff ff 20 ff ff ff ff
> ff ff ff ff ff ff
> [ 40.727947] saa7133[0]: i2c eeprom 20: 01 40 01 02 02 01 01 00 08 ff
> 00 0e ff ff ff ff
> [ 40.727953] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff
> ff ff ff ff ff ff
> [ 40.727961] saa7133[0]: i2c eeprom 40: ff 65 00 ff c2 1e ff ff ff ff
> ff ff ff ff ff ff
> [ 40.727968] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff
> ff ff ff ff ff ff
> [ 40.727975] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff
> ff ff ff ff ff ff
> [ 40.727982] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff
> ff ff ff ff ff ff
> [ 40.727989] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff
> ff ff ff ff ff ff
> [ 40.727996] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff
> ff ff ff ff ff ff
> [ 40.728003] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff
> ff ff ff ff ff ff
> [ 40.728010] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff
> ff ff ff ff ff ff
> [ 40.728017] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff
> ff ff ff ff ff ff
> [ 40.728024] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff
> ff ff ff ff ff ff
> [ 40.728032] saa7133[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff
> ff ff ff ff ff ff
> [ 40.728039] saa7133[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff
> ff ff ff ff ff ff
> [ 40.740151] saa7133[0]: i2c scan: found device @ 0x1e [???]
> [ 40.759885] saa7133[0]: i2c scan: found device @ 0xa0 [eeprom]
> [ 40.901555] saa7133[0]: registered device video0 [v4l2]
> [ 40.901588] saa7133[0]: registered device vbi0
> [ 40.901620] saa7133[0]: registered device radio0
> [ 40.907417] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 22
> [ 40.907423] ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [AAZA] -> GSI
> 22 (level, low) -> IRQ 22
> [ 40.907624] PCI: Setting latency timer of device 0000:00:10.1 to 64
> [ 40.910779] saa7134 ALSA driver for DMA sound loaded
> [ 40.910811] saa7133[0]/alsa: saa7133[0] at 0xfdbff000 irq 17
> registered as card -2
> [ 41.776297] loop: module loaded
> [ 41.799994] lp0: using parport0 (interrupt-driven).
> <snip>
>
> 6) Perhaps I misinterpreted where you meant to put ".tuner_addr =
> ADDR_UNSET,"
> but I now don't even get this:
> > [ 15.296000] tuner' 2-0061: Setting mode_mask to 0x0e
> > [ 15.296000] tuner' 2-0061: chip found @ 0xc2 (saa7133[0])
> > [ 15.296000] tuner' 2-0061: tuner 0x61: Tuner type absent
Argh! I forgot to send the patch to the main tree.
Ok, I've updated saa7134 at v4l-dvb:
http://linuxtv.org/hg/v4l-dvb/rev/3029b981e42c
please, update again and let's see if this time, it will detect xc3028.
Cheers,
Mauro
_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
