> Good job on the wiki so far. At last there is one place that can serve as > a showcase for all the hard work done. After a number of patches I have it compiling and booting with HVR4000 with multiple frontends showing up (test tomorrow if they actually work) cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded cx88[0]: subsystem: 0070:6902, board: Hauppauge WinTV-HVR4000 DVB-S/S2/T/Hybrid [card=59,autodetected] cx88[0]: TV tuner type 63, Radio tuner type -1 cx88/0: cx2388x v4l2 driver version 0.0.6 loaded cx88[0]: i2c init: enabling analog demod on HVR1300/3000/4000 tuner tveeprom 2-0050: Hauppauge model 69009, rev B2D3, serial# 2807241 tveeprom 2-0050: MAC address is 00-0D-FE-2A-D5-C9 tveeprom 2-0050: tuner model is Philips FMD1216MEX (idx 133, type 63) tveeprom 2-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4) tveeprom 2-0050: audio processor is CX882 (idx 33) tveeprom 2-0050: decoder processor is CX882 (idx 25) tveeprom 2-0050: has radio, has IR receiver, has no IR transmitter cx88[0]: hauppauge eeprom: model=69009 input: cx88 IR (Hauppauge WinTV-HVR400 as /class/input/input3 cx88[0]/2: cx2388x 8802 Driver Manager cx88[0]/2: found at 0000:04:08.2, rev: 5, irq: 21, latency: 32, mmio: 0xf8000000 cx8802_probe() allocating 2 frontends cx88[0]/0: found at 0000:04:08.0, rev: 5, irq: 21, latency: 32, mmio: 0xfa000000 cx2388x alsa driver version 0.0.6 loaded cx88/2: cx2388x dvb driver version 0.0.6 loaded cx88/2: registering cx8802 driver, type: dvb access: shared cx88[0]/2: subsystem: 0070:6902, board: Hauppauge WinTV-HVR4000 DVB-S/S2/T/Hybrid [card=59] cx88[0]/2: cx2388x based DVB/ATSC card cx88[0]/0: registered device video0 [v4l2] cx88[0]/0: registered device vbi0 cx88[0]/0: registered device radio0 cx88[0]/1: CX88x/0: ALSA support for cx2388x boards dvb: videobuf_dvb_register_adapter() DVB: registering new adapter (cx88[0]) dvb: videobuf_dvb_register_adapter() returns 0 DVB: registering frontend 0 (Conexant CX22702 DVB-T)... DVB: registering frontend 0 (Conexant CX24116/CX24118)... cx24116_firmware_ondemand: Waiting for firmware upload (dvb-fe-cx24116.fw)... cx24116_firmware_ondemand: Waiting for firmware upload(2)... cx24116_load_firmware: FW version 1.20.79.0 cx24116_firmware_ondemand: Firmware upload complete --------------------------------------------- media1:~# ls -la /dev/dvb/adapter0/ total 0 drwxr-xr-x 2 root root 200 2008-01-23 22:50 . drwxr-xr-x 3 root root 60 2008-01-23 22:50 .. crw-rw---- 1 root video 212, 4 2008-01-23 22:50 demux0 crw-rw---- 1 root video 212, 20 2008-01-23 22:50 demux1 crw-rw---- 1 root video 212, 5 2008-01-23 22:50 dvr0 crw-rw---- 1 root video 212, 21 2008-01-23 22:50 dvr1 crw-rw---- 1 root video 212, 3 2008-01-23 22:50 frontend0 crw-rw---- 1 root video 212, 19 2008-01-23 22:50 frontend1 crw-rw---- 1 root video 212, 7 2008-01-23 22:50 net0 crw-rw---- 1 root video 212, 23 2008-01-23 22:50 net1 I have nothing plugged into the cards at the moment but I can scan (and get nothing) both (but not at the same time). In theory should the DVB-T and DVB-S be able to be used at the same time?? If this is all ok (when I get antenna/satellite dish on card) I just have to get the DVB-S2/multiproto working. Thanks _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
