Re: DViCO FusionHDTV DVB-T Dual

["Collier Family" <judithc@xxxxxxxxxxxxxx>]

I have one of these cards working with both PCI and USB . See posts a few months back mid Febuary.  My only issue now is to get the USB on the second card working. I am using 2.6.17 kernel - sorry I can't be much help over the next 2 weeks but I should be able to help when I get back if you still have the troubles.

 

I see a /dev/dvbX for both USB and PCI for the working device but only PCI for the second device.

 

-Stephen

----- Original Message -----

From: Dean Macauley

To: linux-dvb@xxxxxxxxxxx

Sent: Thursday, June 29, 2006 10:41 AM

Subject: DViCO FusionHDTV DVB-T Dual

Hi,

I have purchased this card, and I have been struggling to get things working with gentoo (kernel 2.6.16).  I am fairly new to playing with linux at this level but I have been learning much thank you to many posts etc...

I have a question regarding this card and what I should expect in terms devices...

Should I see two adapters under /dev/dvb/ ?  At the moment, things seem okay in dmesg (see below) however, I only have one adapter in /dev/dvb/.  The other is /dev/vbi0 ...

I have discovered that one tuner is PCI while the other is USB...

I am loading the following modules:

Module                  Size  Used by
dvb_usb_cxusb          23684  0
mt352                   8196  1 dvb_usb_cxusb
lgdt330x                9692  1 dvb_usb_cxusb
cx22702                 8068  1 dvb_usb_cxusb
dvb_usb                18248  1 dvb_usb_cxusb
dvb_core               77148  1 dvb_usb
dvb_pll                12356  3 dvb_usb_cxusb,cx22702,dvb_usb
cx8800                 30412  0
cx88xx                 62500  1 cx8800
i2c_algo_bit           10184  1 cx88xx
video_buf              20164  2 cx8800,cx88xx
ir_common              10756  1 cx88xx
tveeprom               17040  1 cx88xx
compat_ioctl32          9856  1 cx8800
v4l1_compat            12804  1 cx8800
v4l2_common            10304  2 cx8800,compat_ioctl32
btcx_risc               6216  2 cx8800,cx88xx
videodev               10880  2 cx8800,cx88xx

when I try to modprobe cx88-dvb, I get an error that initialisation failed, while modprobe cx8800 seems to work...  Have I got it right?  Or should I expect two adapters in /dev/dvb?

Thanks in advance!

Dean.

P.S.  dmesg output below

CORE cx88[0]: subsystem: 18ac:db50, board: DViCO FusionHDTV DVB-T Dual Digital [card=44,autodetected]
TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe
cx88[0]/0: found at 0000:05:06.0, rev: 5, irq: 58, latency: 32, mmio: 0xd3000000
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
set_control id=0x980900 reg=0x310110 val=0x00 (mask 0xff)
set_control id=0x980901 reg=0x310110 val=0x3f00 (mask 0xff00)
set_control id=0x980903 reg=0x310118 val=0x00 (mask 0xff)
set_control id=0x980902 reg=0x310114 val=0x5a7f (mask 0xffff)
set_control id=0x980909 reg=0x320594 val=0x40 (mask 0x40) [shadowed]
set_control id=0x980905 reg=0x320594 val=0x20 (mask 0x3f) [shadowed]
set_control id=0x980906 reg=0x320598 val=0x40 (mask 0x7f) [shadowed]
dvb-usb: found a 'DViCO FusionHDTV DVB-T Dual USB' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (DViCO FusionHDTV DVB-T Dual USB).
dvb-usb: recv bulk message failed: -110
dvb-usb: no frontend was attached by 'DViCO FusionHDTV DVB-T Dual USB'
input: IR-receiver inside an USB DVB receiver as /class/input/input4
dvb-usb: schedule remote query interval to 150 msecs.
dvb-usb: DViCO FusionHDTV DVB-T Dual USB successfully initialized and connected.

-- 
Dean Macauley
Team Leader - Datalink Detection Function (DDF)
THALES Air Traffic Management
Phone:  +61 (0)3 9425 7533   Mobile: +61 (0)416 084 591

---

_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

_______________________________________________

linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb