|
Hi, I have purchased this card, and I have been struggling to get things working with gentoo (kernel 2.6.16). I am fairly new to playing with linux at this level but I have been learning much thank you to many posts etc... I have a question regarding this card and what I should expect in terms devices... Should I see two adapters under /dev/dvb/ ? At the moment, things seem okay in dmesg (see below) however, I only have one adapter in /dev/dvb/. The other is /dev/vbi0 ... I have discovered that one tuner is PCI while the other is USB... I am loading the following modules: Module Size Used by dvb_usb_cxusb 23684 0 mt352 8196 1 dvb_usb_cxusb lgdt330x 9692 1 dvb_usb_cxusb cx22702 8068 1 dvb_usb_cxusb dvb_usb 18248 1 dvb_usb_cxusb dvb_core 77148 1 dvb_usb dvb_pll 12356 3 dvb_usb_cxusb,cx22702,dvb_usb cx8800 30412 0 cx88xx 62500 1 cx8800 i2c_algo_bit 10184 1 cx88xx video_buf 20164 2 cx8800,cx88xx ir_common 10756 1 cx88xx tveeprom 17040 1 cx88xx compat_ioctl32 9856 1 cx8800 v4l1_compat 12804 1 cx8800 v4l2_common 10304 2 cx8800,compat_ioctl32 btcx_risc 6216 2 cx8800,cx88xx videodev 10880 2 cx8800,cx88xx when I try to modprobe cx88-dvb, I get an error that initialisation failed, while modprobe cx8800 seems to work... Have I got it right? Or should I expect two adapters in /dev/dvb? Thanks in advance! Dean. P.S. dmesg output below CORE cx88[0]: subsystem: 18ac:db50, board: DViCO FusionHDTV DVB-T Dual Digital [card=44,autodetected] TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe cx88[0]/0: found at 0000:05:06.0, rev: 5, irq: 58, latency: 32, mmio: 0xd3000000 cx88[0]/0: registered device video0 [v4l2] cx88[0]/0: registered device vbi0 set_control id=0x980900 reg=0x310110 val=0x00 (mask 0xff) set_control id=0x980901 reg=0x310110 val=0x3f00 (mask 0xff00) set_control id=0x980903 reg=0x310118 val=0x00 (mask 0xff) set_control id=0x980902 reg=0x310114 val=0x5a7f (mask 0xffff) set_control id=0x980909 reg=0x320594 val=0x40 (mask 0x40) [shadowed] set_control id=0x980905 reg=0x320594 val=0x20 (mask 0x3f) [shadowed] set_control id=0x980906 reg=0x320598 val=0x40 (mask 0x7f) [shadowed] dvb-usb: found a 'DViCO FusionHDTV DVB-T Dual USB' in warm state. dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. DVB: registering new adapter (DViCO FusionHDTV DVB-T Dual USB). dvb-usb: recv bulk message failed: -110 dvb-usb: no frontend was attached by 'DViCO FusionHDTV DVB-T Dual USB' input: IR-receiver inside an USB DVB receiver as /class/input/input4 dvb-usb: schedule remote query interval to 150 msecs. dvb-usb: DViCO FusionHDTV DVB-T Dual USB successfully initialized and connected. -- Dean Macauley Team Leader - Datalink Detection Function (DDF) THALES Air Traffic Management Phone: +61 (0)3 9425 7533 Mobile: +61 (0)416 084 591 |
_______________________________________________ linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
