On Sun, 2006-04-16 at 23:57 -0700, Ken Harris wrote:
> Sirs:
>
> I did some tests with a voltmeter and an oscilloscope a few days
> ago:
>
> dvb-apps/test/setvoltage: doesn't seem to work
> dvb-apps/test/set22k: works OK
> dvb-apps/test/sendburst: doesn't seem to work
> dvb-apps/test/diseqc: seems to work
>
> An odd symptom is that when I ran 'dvbscan', then the voltage did change
> (from 13v to 19v), but I couldn't use 'setvoltage' to change it.
This I think is caused by the fact that with this card several of these
parameters are set at once. For instance there is a call to the card
called "tone_voltage_cmd", so if you pass only tone to the driver it
will cache this, then do the actual command once it has got enough
parameters known. There is also a slight possibility that it caches
passed parameters and doesn't set anything before you actually try to
tune.
Regards
Sigmund
>
>
> On Mon, 3 Apr 2006, Ken Harris wrote:
>
> >
> > Sirs:
> >
> > FYI, Manu's fixes work with the VP1025 and Fedora Core 4:
> >
> > DVB: registering new adapter (bttv0).
> > dst(0) dst_get_device_id: Recognise [DST-03T]
> > dst(0) dst_get_device_id: Unsupported
> > dst(0) dst_get_device_id: [DST-03T] has a [Fujitsu MB86A15]
> > DST type flags : 0x2 ts204 0x4 symdiv 0x10 firmware version = 2
> > dst(0) dst_get_mac: MAC Address=[00:08:ca:17:49:00]
> > DVB: registering frontend 0 (DST DVB-S)...
> >
> > I didn't do any of the modprobe.conf stuff.
> >
> > On Fri, 31 Mar 2006, Ken Harris wrote:
> >
> >> I tried to compile Manu's modules on Fedora Core 5, but I got an
> >> error:
> >
> >> cgi-bin-hgwebdir-cgi-v4l-algo-test-70266933831b/v4l/flexcop-usb.c:547:
> >> error: unknown field 'owner' specified in initializer
> >
> >> FYI, it compiled fine with Fedora Core 4, but I can't test it with
> >> the VP1025 because it's at work, so I should be able to test it on Monday.
> >
> >> On Fri, 31 Mar 2006, Ray Clouse wrote:
> >
> >>> This is the key email. Get that kernel module and you should be on your
> >>> way.
> >
> >>> Also, you need the following in modprobe.conf:
> >
> >>> options dst dst_algo=0
> >>> options bttv card=0x71
> >>> install bttv /sbin/modprobe --ignore-install bttv && /sbin/modprobe
> >>> dvb_bt8xx
> >>> remove dvb { /sbin/modprobe -r dvb-bt8xx; }
> >>> alias char-major-81 bttv
> >
> >>> ---------- Forwarded message ----------
> >>> From: Manu Abraham <abraham.manu@xxxxxxxxx>
> >>> Date: Feb 8, 2006 10:41 AM
> >>> Subject: Re: Twinhan 1025 problem - Knoppix works, FC4 &
> >>> Ubuntu don't
> >>> To: Wei Weng <wweng@xxxxxxxxxxx>
> >>> Cc: Ray Clouse <rclouse@xxxxxxxxx>, linux-dvb@xxxxxxxxxxx
> >
> >>> Wei Weng wrote:
> >>>> Looks exactly like the problem I had been having. (No, I was not able
> >>>> to figure it out)
> >
> >>> Please do check whether this helps ..
> >
> >>> http://www.thadathil.net/cgi-bin/hgwebdir.cgi/v4l-algo-test?cmd=archive;node=70266933831bc8efd85ecf808651595f79aede60;type=bz2
> >
> >>> For build instructions please do refer to the v4l-dvb build instructions.
> >>> A simple make should build in most cases. Would like to get your feedback
> >>> on this.
> >
> >>> Manu
> >
>
> _______________________________________________
>
> linux-dvb@xxxxxxxxxxx
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
_______________________________________________
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
