I see you have the r2.6C card. I'm thinking about purchasing one of these but r2.6D to replace my Twinhan card. Is the 2.6D revision well supported? Thanks, Mark. On 1/26/06, Pavel Paprok <ppaprok@xxxxxxxxx> wrote: > > Hi, > thanks for all answers, problem is solved! > - I removed card from slot, clean contacts > on it and reseal, on other PCI position > to be sure :-) and then all things on card start > to works. Maybe some dirty contact caused > that card seems like was partially broken... > > Pavel > > > ----- Original Message ----- > From: "Patrick Boettcher" <patrick.boettcher@xxxxxxx> > To: "Pavel Paprok" <ppaprok@xxxxxxxxx> > Cc: <linux-dvb@xxxxxxxxxxx> > Sent: Thursday, January 19, 2006 9:13 AM > Subject: Re: [linux-dvb] SkyStar2 reporting unknown FlexCop revision > > > > Hi Pavel, > > > > On Thu, 19 Jan 2006, Pavel Paprok wrote: > >> I just try my first sat card, it is a SkyStar2, on card is printed > >> exactly: > >> > >> MODEL: SKYSTAR 2 > >> P/N 92105-20003 > >> REV: 2.6C > >> > >> unfortunatelly in lastest 2.6 kernel (exactly 2.6.15 vanilla without > any > >> extra patches) > >> card seems to not work, b2c2 driver reporting in log: > >> > >> Jan 18 19:06:42 dvb kernel: b2c2-flexcop: B2C2 FlexcopII/II(b)/III > >> digital TV receiver chip loaded successfully > >> Jan 18 19:06:42 dvb kernel: flexcop-pci: will use the HW PID filter. > >> Jan 18 19:06:42 dvb kernel: flexcop-pci: card revision 1 > >> Jan 18 19:06:42 dvb kernel: ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI > 17 > >> (level, low) -> IRQ 185 > >> Jan 18 19:06:42 dvb kernel: b2c2-flexcop: unkown FlexCop Revision: f. > >> Please report the linux-dvb@xxxxxxxxxxxx > > > > On which platform you are using the flexcop-driver? PPC or (normal) PC? > > Most likely your card is broken. To be sure that it is not a driver > > problem, you should try it in windows. > > > >> Jan 18 19:06:42 dvb kernel: DVB: registering new adapter (FlexCop > Digital > >> TV device). > >> Jan 18 19:06:42 dvb kernel: b2c2-flexcop: reading of MAC address > failed. > >> Jan 18 19:06:42 dvb kernel: > >> Jan 18 19:06:42 dvb kernel: b2c2-flexcop: i2c master_xfer failed > >> Jan 18 19:06:42 dvb last message repeated 2 times > >> Jan 18 19:06:42 dvb kernel: mt352_read_register: readreg error > (reg=127, > >> ret==-121) > >> Jan 18 19:06:42 dvb kernel: b2c2-flexcop: i2c master_xfer failed > >> Jan 18 19:06:42 dvb kernel: i2c_readbytes: i2c read error (addr 0a, err > >> == -121) > >> Jan 18 19:06:42 dvb kernel: b2c2-flexcop: i2c master_xfer failed > >> Jan 18 19:06:42 dvb kernel: lgdt330x: i2c_read_demod_bytes: addr 0x59 > >> select 0x02 error (ret == -121) > >> Jan 18 19:06:42 dvb kernel: b2c2-flexcop: i2c master_xfer failed > >> Jan 18 19:06:42 dvb kernel: b2c2-flexcop: i2c master_xfer failed > >> Jan 18 19:06:42 dvb kernel: stv0297_readreg: readreg error (reg == > 0x80, > >> ret == -22) > >> Jan 18 19:06:42 dvb kernel: b2c2-flexcop: i2c master_xfer failed > >> Jan 18 19:06:42 dvb kernel: mt312_read: ret == -121 > >> Jan 18 19:06:42 dvb kernel: b2c2-flexcop: no frontend driver found for > >> this B2C2/FlexCop adapter > > > > That there is not frontend found (and thus a lot of i2c-errors) also > > indicates that the card is broken. > > > > I'm sorry, > > Patrick. > > > > -- > > Mail: patrick.boettcher@xxxxxxx > > WWW: http://www.wi-bw.tfh-wildau.de/~pboettch/ > > > > > _______________________________________________ > > linux-dvb@xxxxxxxxxxx > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb > -------------- next part -------------- An HTML attachment was scrubbed... URL: http://www.linuxtv.org/pipermail/linux-dvb/attachments/20060126/cb903fad/attachment.htm
