Hi, Rainer
Rainer Schubert wrote:
> On Tue, 15 Nov 2005, bardinov@xxxxxx wrote:
>
>> Hi,
>
>
> Hi Vince and the list,
>
>> I try to install the pinnacle 310i but without success.
>
> ~~~~~~~~~~~~~
> As far as I know, the Pinnacle 310i is quite different from
> the Pinnacle 300i card and is not supported yet.
>
>> I have debian with kernel 2.6.14.2
>> I do modprobe saa7134 card=50 tuner=3
>> $ dmesg
>> saa7130/34: v4l2 driver version 0.2.14 loaded
>> saa7133[0]: found at 0000:01:07.0, rev: 208, irq: 177, latency: 32, mmio:
>> 0xf5001000
>> saa7133[0]: subsystem: 11bd:002f, board: Pinnacle PCTV 300i DVB-T + PAL
>> [card=50,insmod option]
>
>
> On the above line you can see that the Pinnacle 300i card is supported,
> but the 310i is NOT. That is why initialisation fails, as you can see
> below.
>
>> saa7133[0]: board init: gpio is 600c000
>> saa7133[0]: dsp access wait timeout [bit=WRR]
>> saa7133[0]: dsp access wait timeout [bit=WRR]
>> saa7133[0]: dsp access wait timeout [bit=WRR]
>> tuner 0-004b: chip found @ 0x96 (saa7133[0])
>> saa7133[0]: i2c eeprom 00: bd 11 2f 00 54 20 1c 00 43 43 a9 1c 55 d2
>> b2 92
>> saa7133[0]: i2c eeprom 10: ff e0 60 06 ff 20 ff ff 00 30 8d 2c 43 46
>> ff ff
>> saa7133[0]: i2c eeprom 20: 01 2c 01 02 02 01 04 30 98 ff 00 a5 ff 21
>> 00 c2
>> saa7133[0]: i2c eeprom 30: 96 10 03 32 15 20 ff ff 0c 22 17 88 03 28
>> bf a8
>> saa7133[0]: registered device video0 [v4l2]
>> saa7133[0]: registered device vbi0
>>
>> modprobe saa7134-dvb gives me that error in dmesg:
>> saa7133[0]: pinnacle 300i dvb setup
>> saa7133[0]: frontend initialization failed
>>
>> I can't make work analog and digital tv.
>> I only have balck screen for all analog channels with tvtime, xawtv or
>> mplayer.
>>
>> Could you help me to have at least analog tv working?
>
>
> As far as I have been told, the Pinnacle 300i and 310i are sold in France
> as DVB-T only, because their analogue part is designed for the PAL TV
> standard that we use over here in Germany, while you have SECAM.
>
> Please correct me, if I am wrong.
>
As far as we know, the board is stuffed with
saa7133
tda8290
tda8275a
tda10046
If this is correct, the analog part is multi system and should work
with SECAM-L as well as with PAL-B/G.
People have reported partial success with card type 77. SInce it is a hybrid
board, i would like you to try card 81 from recent CVS. It also supports
DVB-T.
Good luck
Hartmut
