Hi, Nick
Not sure whether t200 and t200a are software compatible. The t200
is known to work. The eeprom dump gives me the impression (not sure)
that your board is stuffed with another tuner.
Please have a closer look at the board. Do you find a chip tda9889?
and a small tuner metal can?
If you find the tda9889, the driver for the t300 might work.
To get it, you will need to load the saa7134 module with
modprobe saa7134 card=70
A picture also might help.
Good luck
Hartmut
Nick Farrell wrote:
> Hi.
>
> My problem seems quite similar to this one:
> http://www.linuxtv.org/pipermail/linux-dvb/2005-September/004669.html
>
> In short, I've got the latest CVS code, compiled it against the stock
> 2.6.13, and loaded the saa7134-dvb module:
> (My Linux flavour is Breezy Badger, by the way)
>
>> saa7130/34: v4l2 driver version 0.2.14 loaded
>> saa7130[0]: found at 0000:01:02.0, rev: 1, irq: 18, latency: 32, mmio:
>> 0xf9000000
>> saa7130[0]: subsystem: 185b:c901, board: Compro Videomate DVB-T200
>> [card=71,autodetected]
>> saa7130[0]: board init: gpio is 943f00
>> saa7130[0]: registered input device for IR
>> saa7130[0]: i2c eeprom 00: 5b 18 01 c9 54 20 1c 00 43 43 a9 1c 55 d2
>> b2 92
>> saa7130[0]: i2c eeprom 10: 00 ff 86 0f ff 20 ff ff ff ff ff ff ff ff
>> ff ff
>> saa7130[0]: i2c eeprom 20: 01 40 01 03 03 ff 03 01 08 ff 00 88 ff ff
>> ff ff
>> saa7130[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> ff ff
>> saa7130[0]: i2c eeprom 40: ff 02 00 c2 86 10 ff ff ff ff ff ff ff ff
>> ff ff
>> saa7130[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> ff cb
>> saa7130[0]: i2c eeprom 60: 30 ff ff ff ff ff ff ff ff ff ff ff ff ff
>> ff ff
>> saa7130[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> ff ff
>> saa7130[0]: registered device video0 [v4l2]
>> saa7130[0]: registered device vbi0
>> DVB: registering new adapter (saa7130[0]).
>> DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
>
>
>
> If I then run tzap (with the right channels.conf file) I get this:
>
>> tda1004x: found firmware revision 23 -- ok
>
>
>
> and this to STDOUT:using '/dev/dvb/adapter0/frontend0' and
> '/dev/dvb/adapter0/demux0'
>
>> tuning to 536500000 Hz
>> video pid 0x0066, audio pid 0x0067
>> status 00 | signal 0000 | snr ffff | ber 0001fffe | unc 00000000 |
>> status 00 | signal 0000 | snr ffff | ber 0001fffe | unc 00000000 |
>> status 00 | signal 0000 | snr ffff | ber 0001fffe | unc 00000000 |
>> ...
>
>
>
> I just bought a new antenna, thinking perhaps it was just bad signal,
> but there's no change at all. Am I missing a tuner in the kernel?
>
> Thanks in advance for any tips.
>
> Nick.
>
> _______________________________________________
>
> linux-dvb@xxxxxxxxxxx
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>
