On Saturday 07 May 2005 23:32, Keith Hopkins wrote: > > Can you post the output of dmesg after modprobing cx88-dvb. > > modprobe cx88-dvb adds the following: > > Module Size Used by > cx88_dvb 6148 0 > cx8802 8452 1 cx88_dvb > mt352 6404 1 cx88_dvb > cx88xx 43924 2 cx88_dvb,cx8802 > i2c_algo_bit 9096 1 cx88xx > btcx_risc 5000 2 cx8802,cx88xx > videodev 8576 1 cx88xx > video_buf_dvb 5508 1 cx88_dvb > dvb_core 76712 1 video_buf_dvb > video_buf 17540 4 cx88_dvb,cx8802,cx88xx,video_buf_dvb > > and dmesg looks like: > Linux video capture interface: v1.00 > cx2388x dvb driver version 0.0.4 loaded > cx88[0]: subsystem: 18ac:db11, board: DVICO UltraviewHDTV DVB-T Plus > [card=22,autodetected] i2c-algo-bit.o: (0) scl=1, sda=1 > i2c-algo-bit.o: (1) scl=1, sda=0 > i2c-algo-bit.o: (2) scl=1, sda=1 > i2c-algo-bit.o: (3) scl=0, sda=1 > i2c-algo-bit.o: (4) scl=1, sda=1 > i2c-algo-bit.o: cx88[0] passed test. > ACPI: PCI interrupt 0000:01:06.2[A] -> GSI 18 (level, high) -> IRQ 209 > cx88[0]/2: found at 0000:01:06.2, rev: 5, irq: 209, latency: 32, mmio: > 0xe9000000 cx88[0]/2: cx2388x based dvb card > DVB: registering new adapter (cx88[0]). > DVB: registering frontend 0 (DVICO UltraviewHDTV DVB-T Plus)... > > > When I first got my cx88 dvb card it was not supported, but I could > > still use the svideo port with v4l device, the cx88xx module just picked > > it up as a unknown/generic card but worked just fine, for the analog part > > only. > > This makes me wonder why xawtv isn't attaching to at least the analog > input. > > can't open /dev/video0: No such device > > can't open /dev/dvb/adapter0/video0: No such device > > 0000:01:06.0 Class 0400: 14f1:8800 (rev 05) > Subsystem: 18ac:db11 > Flags: bus master, medium devsel, latency 32, IRQ 5 > Memory at e8000000 (32-bit, non-prefetchable) > Capabilities: [44] Vital Product Data > Capabilities: [4c] Power Management version 2 > > 0000:01:06.2 Class 0480: 14f1:8802 (rev 05) > Subsystem: 18ac:db11 > Flags: bus master, medium devsel, latency 32, IRQ 209 > Memory at e9000000 (32-bit, non-prefetchable) > Capabilities: [4c] Power Management version 2 > > > I'll give 2.6.12-rc* a shot next. > > --Keith Keith, Sorry, I did not explain properly, the dvb device is like so, /dev/dvb/adaptor0/demux0 /dev/dvb/adaptor0/dvr0 /dev/dvb/adaptor0/frontend0 /dev/dvb/adaptor0/net0 Im am not sure if xawtv supports dvb, ive never tried, I use mythtv for dvb. I know you can use mplayer or xine to do so. Try this site for instructions on using the DVB card with linux http://forums.dvbowners.com/index.php?showtopic=1346 Go down to part "5.Installing and configuring DVB applications" For the analog part of the card I see you dont have the V4l modules loaded so try modprobing- cx8800 which should also load v4l2_common and v4l1_compat, mine looks like this after a modprobe cx8800 Linux video capture interface: v1.00 cx2388x v4l2 driver version 0.0.4 loaded ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 17 (level, low) -> IRQ 17 cx88[0]: subsystem: 17de:08a6, board: KWorld/VStream XPert DVB-T [card=14,autodetected] cx88[0]/0: found at 0000:00:06.0, rev: 5, irq: 17, latency: 32, mmio: 0xec000000 cx88[0]/0: registered device video0 [v4l2] cx88[0]/0: registered device vbi0 Notice the video0 and vbi0 getting registered. Hope this helps to get you going. Andrew.
