Le samedi 10 mars 2007 à 10:57 -0600, j.c.w. a écrit :
> Hey there,
Hi,
> You need the snd-rme9652 module. I don't have any of the hdsp stuff
> at all (to my knowledge). The contents of the file produced by
Same thing here with "snd-rme9652" loaded. Regarding hdsp stuff, it is
needed to load snd-hdsp too (or "hdspmixer" and "hdsonf" refused to
run).
> "alsactl store -f myconfig.conf" might prove useful once you have the
> snd-rme9652 loaded and all that jazz.
>
> I have the 9632 with the daughter I/O cards up and running without
> any issues and i also run debian/sid.
:-(
What is your kernel version? Debina or vanilla?
Could you send me a screenshot (a part from the list) of your
"hdspmixer", "hdspconf", jack settings, "lsmod" output, "alsactl store
-f myconfig.conf", and ".asoundrc"? Hum... A lot of work for you I
guess :-(
> Good luck and shout if getting the module in doesn't do the trick.
> Folks please feel free to jump in if I'm misleading this poor chap.
> It's been a while (fortunately) since I've had to dig into any of this.
>
> rock on.
I wish I could :-)
Perhaps a problem of RME firmware version ("lspci -v" give me "rev98")
that could not be understound by current alsa drivers?
-----
$ lspci -v
04:00.0 Multimedia audio controller: Xilinx Corporation RME Hammerfall
DSP (rev 98)
Flags: bus master, medium devsel, latency 255, IRQ 16
Memory at dcdd0000 (32-bit, non-prefetchable) [size=64K]
-----
Isn't the latency too hight? When I try to run "ZynAddSubFX" or
"Hydrogen" I have a lot of xruns (and always only a bad mono sound on
the "playback_9" jack port).
Thanks for your help. I am a bit disappointed.
Bye
> > Hi all,
> >
> > I just bought a RME HDSP 9632 today but I cannot make it work.
> >
> > Yes, another guy with this same eternal problem...
> >
> > I already know that this card is (should be?) well supported under
> > GNU/Linux (and in fact it is why I bought it)...
> >
> > My system/conf is:
> >
> > -----
> > * Distro: Debian/Sid
> >
> > * Kernel: vanilla 2.6.20.2 (+ realtime-lsm) with the following
> > specific
> > ALSA modules:
> >
> > RME Hammerfall DSP Audio
> > RME Digi96, 96/8, 96/8 PRO
> > RME Digi9652 (Hammerfall)
> >
> > What is the module I must use for a 9632?
> >
> > $ lsmod | grep hdsp
> > snd_hdsp 43812 0
> > snd_rawmidi 18848 3 snd_seq_virmidi,snd_hdsp,snd_seq_midi
> > snd_pcm 59908 3 snd_rme96,snd_hdsp,snd_pcm_oss
> > snd_page_alloc 8328 2 snd_hdsp,snd_pcm
> > snd_hwdep 7428 1 snd_hdsp
> > snd 41828 12
> > snd_seq_virmidi,snd_rme96,snd_hdsp,snd_seq_oss,snd_seq,snd_rawmidi,snd
> > _seq_device,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_hwdep
> > $ lsmod | grep rme
> > snd_rme96 20516 0
> > snd_pcm 59908 3 snd_rme96,snd_hdsp,snd_pcm_oss
> > snd 41828 12
> > snd_seq_virmidi,snd_rme96,snd_hdsp,snd_seq_oss,snd_seq,snd_rawmidi,snd
> > _seq_device,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_hwdep
> > -----
> >
> > I even try to use "hdsploader", but as far as I understand how it
> > works,
> > it is not required for the 9632:
> >
> > -----
> > $ hdsploader
> > hdsploader - firmware loader for RME Hammerfall DSP cards
> > Looking for HDSP + Multiface or Digiface cards :
> > Card 0 : RME Hammerfall HDSP 9632 at 0xdcdd0000, irq 16
> > -----
> >
> > Do you need more informations/screenshots about my system/conf?
> >
> > I have installed "alsa-tools" and "alsa-tools-gui" for "hdspmixer" and
> > "hdspconf".
> >
> > "alsamixer" give me very poor information (but I have unmutted all I
> > could unmutted with it).
> >
> > I have tried to use a ".asoundrc" file, but with no success.
> >
> > -> Notice that before RME I used to work with a Audigy2 and all was
> > ok.
> > But now the only little "sound" I can have is with jack (and only on
> > playback_9 port, in the headphone left part).
> >
> > Any idea?
> >
> > Thanks for your help...
