On 12/05/2013 11:52 AM, Mark Rutland wrote:
Hi,
Apologies for the late reply.
Hi Mark, thanks for the review!
On Wed, Nov 06, 2013 at 03:56:44PM +0000, Georgi Djakov wrote:
This patch adds documentation for Qualcomm SDHCI MSM driver.
It contains the differences between the core properties in mmc.txt
and the properties used by the sdhci-msm driver.
Nit, but this is documentation of the binding, not the driver.
Ok, sure!
Signed-off-by: Georgi Djakov <gdjakov@xxxxxxxxxx>
---
.../devicetree/bindings/mmc/sdhci-msm.txt | 92 ++++++++++++++++++++
1 file changed, 92 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-msm.txt
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt
new file mode 100644
index 0000000..8f1a52d
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt
@@ -0,0 +1,92 @@
+* Qualcomm SDHCI controller (sdhci-msm)
+
+This file documents differences between the core properties in mmc.txt
+and the properties used by the sdhci-msm driver.
+
+Required properties:
+- compatible: should contain "qcom,sdhci-msm"
+- reg: should contain SDHC, SD Core register map
As this seems to depend on reg-names, it would be nice to write this in
terms of reg-names (as with clocks and clock-names).
Ok, thanks!
+- reg-names: indicates various resources passed to driver (via reg proptery) by name
+ "reg-names" examples are "hc_mem" and "core_mem"
Either there are a fixed set of names you expect (and therefore these
aren't examples but rather a definition), or this property is useless.
Please either define the set of names or remove this property.
+- interrupts: should contain SDHC interrupts
+- interrupt-names: indicates interrupts passed to driver (via interrupts property) by name
+ "interrupt-names" examples are "hc_irq" and "pwr_irq"
Likewise for both points.
Ok!
+- vdd-supply: phandle to the regulator for the vdd (flash core voltage) supply.
+- vddio-supply: phandle to the regulator for the vdd-io (i/o voltage) supply.
+- pinctrl-names: Should contain only one value - "default".
+- pinctrl-0: Should specify pin control groups used for this controller.
+- clocks: A list of phandle + clock-specifier pairs for the clocks listed in clock-names
+- clock-names: Should contain the following:
+ "iface" - Main peripheral bus clock (PCLK/HCLK - AHB Bus clock) (required)
+ "core" - SDC MMC clock (MCLK) (required)
+ "bus" - SDCC bus voter clock (optional)
This looks good :)
+
+Optional properties:
+- qcom,bus-speed-mode: specifies the supported bus speed modes by host
+ The supported bus speed modes are:
+ "HS200_1p8v" - indicates that host can support HS200 at 1.8v
+ "HS200_1p2v" - indicates that host can support HS200 at 1.2v
+ "DDR_1p8v" - indicates that host can support DDR mode at 1.8v
+ "DDR_1p2v" - indicates that host can support DDR mode at 1.2v
Is this a list of strings, or does the unit only support one of these?
This could be a set of boolean properties instead, is this likely to
expand in future?
It is meant to be list of strings, and many can be supported. But i will
drop this property from this initial version, and maybe add it later as
boolean properties! Thanks!
+
+- qcom,{vdd,vdd-io}-lpm-sup - specifies whether the supply can be kept in low power mode.
Boolean? Please specify types on properties.
Yes, it is boolean. I'll note it in the documentation. Thanks!
Can you elaborate on what this means? When can a supply not be kept in
low power mode?
The vdd-io for example is a regulator that is always-on and may be
shared with multiple other peripherals as well. It should not be
disabled by the driver, but instead put in low power mode when unused.
+- qcom,{vdd,vdd-io}-voltage-level - specifies voltage levels for the supply.
+ Should be specified in pairs (min, max), units uV.
+- qcom,{vdd,vdd-io}-current-level - specifies load levels for the supply in lpm
+ or high power mode (hpm). Should be specified in pairs (lpm, hpm), units uA.
Can you not query these from the regulator framework?
If these are configuration, why are they necessary?
As some regulators are shared and can have multiple consumers, these
properties can be used for voltage and load current aggregation.
The voltage-level is the "supported voltage" by the controller, that
also (at least on my platform) matches the corresponding regulator
voltage. I probably can drop the voltage-level property and get voltage
via the regulator framework helper functions, but the load current
values are different for each sdhc.
From the very limited documentation that i have, i think this is
describing the hardware configuration and should be in the device-tree.
Thanks,
Georgi
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
