Hi Jack, > -----Original Message----- > From: jack.kelly.productions@xxxxxxxxxxxxxx > [mailto:jack.kelly.productions@xxxxxxxxxxxxxx] On Behalf Of Jack Kelly > Sent: Monday, September 24, 2012 9:03 PM > To: R, Durgadoss > Cc: linux-acpi@xxxxxxxxxxxxxxx; Zhang, Rui > Subject: Re: HP laptop: fan off until CPU temp near 105 degrees C > > Dear Durga, > > Thanks so much for your very quick reply! Sorry my first email was so > long (and slightly grumpy on re-reading it!) > > Answers to your questions: > > ----------------- > > 1. What does your temp2_crit report ? > > $ pwd > /sys/class/hwmon/hwmon1/device > > $ ls > driver name temp2_crit temp2_label temp4_crit_alarm temp4_max > hwmon power temp2_crit_alarm temp2_max temp4_input uevent > modalias subsystem temp2_input temp4_crit temp4_label > > $ cat name temp2_label temp2_input temp2_max temp2_crit > temp2_crit_alarm > coretemp <-- name > Core 0 <-- label > 104000 <-- input > 95000 <-- max > 105000 <-- crit > 0 <-- crit_alarm IMO, this crit_alarm should become 1 when your CPU temperature reaches 105 C. Does this happen ? > > (the "cat" command above was run whilst the machine was also running > "stress -c 8". The fan had just started). > > > ---------------------- > > 2. regarding trip_point_0_temp: > > as far as I can tell, none of the 10 directories > /sys/class/thermal/thermal_zone[0-9]/ contain temperature measurements > from my CPU. None of the thermal_zone?/temp files change when I > heavily load my CPU. No they won't change. The CPU temperature is reported under the above hwmon sysfs you mentioned. > > Instead the temp measurements from my CPU appear to live in > /sys/class/hwmon/hwmon1/device. There do not appear to be any > "trip_point" files in /sys/class/hwmon/hwmon1/device. No there won't be any trip_point files in hwmon. > > -------------------- > > 3. Could you please post the output of all cooling_device?/type > interfaces here ? > > $ cat /sys/class/thermal/cooling_device?/type > Processor > Processor > Processor > Processor > LCD Okay, That explains a bit of it. You have CPU cores and LCD registered as cooling devices. But I believe throttling these things would require some intelligence/information from ACPI tables.. Not sure whether your BIOS has them.. May be Rui can help us here.. > > But if I query the current state of each cooling device while the fan > is running: > > $ cat /sys/class/thermal/cooling_device?/cur_state > 0 > 0 > 0 > 0 > 24 If we have processor throttling enabled, the first four 0's should change to something non-zero number. > > However, one further issue to mention is that when the core CPU temp > gets to 105 degrees C under Linux, the fan does not run continuously. > Instead the motherboard appears to rapidly turn the fan on and off > (I've checked by applying a volt meter to the fan connector). The end > result is that the fan makes a sound a little like a hard disk > seeking. My naive guess would be that something like this is > happening: the CPU gets to 105 so the fan turns on so the CPU drops > to 104 so the fan turns off so the CPU gets to 105 etc etc (is this > called "hysteresis"?) AFAIK, The coretemp driver does not do/handle any hysteresis like this. My best guess is again the BIOS has something configured to do like this. Thanks, Durga > > The fan runs continuously under Windows. > > Thanks again for responding to my post. It'd be wonderful to be able > to fix this issue without having to resort to a soldering iron ;) > > Thanks again, > Jack > > > > On 24 September 2012 15:21, R, Durgadoss <durgadoss.r@xxxxxxxxx> wrote: > > Hi Jack, > > > > That's a really long e-mail to start with.. > > > > Some of your findings are correct: > > > > 1. Coretemp module does not control fan speed. It reports > > only CPU temperature. Nothing inside /sys/class/thermal/ > > reports CPU temperature. temp2_max is not writeable. > > What does your temp2_crit report ? > > > > 2. trip_point_0_temp is not writeable...But recently there are > > patches that make it writeable. If you are interested, please > > give this patch here, a try: > > http://www.spinics.net/lists/linux-pm/msg27925.html > > > > 3. Could you please post the output of all cooling_device?/type > > interfaces here ? > > > > Thanks, > > Durga > >> -----Original Message----- > >> From: linux-acpi-owner@xxxxxxxxxxxxxxx [mailto:linux-acpi- > >> owner@xxxxxxxxxxxxxxx] On Behalf Of Jack Kelly > >> Sent: Monday, September 24, 2012 2:43 PM > >> To: linux-acpi@xxxxxxxxxxxxxxx > >> Subject: HP laptop: fan off until CPU temp near 105 degrees C > >> > >> Dear Linux ACPI list, > >> > >> I am having a serious problem with the control of the CPU fan on my HP > >> ProBook 6450b laptop and it has been suggested to me that this may be > >> a Linux ACPI issue. When the machine first powers on, the fan runs > >> (as expected). If I boot into Windows then the fan continues running > >> (as expected). However, if I boot into Linux then the fan turns off > >> during the boot sequence. The fan does not turn on again until the > >> CPU gets close to 105 degrees C, which sounds dangerously hot to me. > >> I want the fan to run continually but I cannot find a way to make the > >> fan run continually. > >> > >> ********************************* > >> Lots more details of this issue: > >> ********************************* > >> > >> This isn't a hardware issue > >> ---------------------------- > >> The failure of the fan to start isn't a hardware issue: the fan is > >> free from dust and the fan runs perfectly in Windows 7, grub, and the > >> laptop BIOS screen. > >> > >> > >> What's so bad about 105 degrees C? > >> ---------------------------------- > >> The processor's specification sheet states that the processor (an i5) > >> can handle a max core temp (t_junction) of 105 degrees C. But the > >> plastic keyboard immediately above the CPU almost certainly can't! And > >> my lap can't either (the side and the bottom of the laptop literally > >> get too hot to touch). And the motherboard probably doesn't enjoy the > >> thermal stresses either. There are reports on various forums of > >> motherboards needing to be replaced and forced shutdowns due to > >> overheating. So, however you look at it, the laptop CPU cores should > >> never be allowed to get anywhere near 105 degrees C IMHO. Windows 7 > >> keeps the CPU below 70 degrees C, even under heavy load. > >> > >> The fact that Linux allows the CPU to get so hot is a very serious problem > >> IMHO. > >> > >> > >> The desired fix > >> --------------- > >> The problem is not to do with throttling the CPU. The solution is > >> simple: the fan should just be on all the time. (I'm seriously > >> considering just permanently connecting power to the fan.) Or, even > >> better, I (the user) should be allowed to specify the CPU temperature > >> at which the fan turns on. > >> > >> > >> Things I've tried > >> ----------------- > >> Alternative Linux distros > >> I'm running Ubuntu 12.04 64-bit so I thought I'd try some > >> alternatives. They all exhibited exactly the same behaviour of the > >> fan: > >> > >> Fedora 17 64-bit live CD (kernel 3.3.4) > >> Ubuntu 12.10 pre-release 64-bit live CD (kernel 3.5) > >> Ubuntu 12.04 32-bit live CD (kernel 3.2.0) > >> Ubuntu 11.10 64-bit live CD (kernel 3.0.4) > >> Ubuntu 11.04 64-bit live CD (kernel 2.6.38) > >> Ubuntu 10.10 64-bit live CD (kernel 2.6.35) > >> > >> > >> lm-sensors and fancontrol > >> ------------------------- > >> I ran sensors-detect. It told me to add the coretemp module to > >> /etc/modules, which I did. > >> - sensors reports the temperature of both my physical CPU cores. > >> - pwmconfig complains that "There are no pwm-capable sensor modules > >> installed" so I can't use fancontrol. > >> > >> > >> i8kutils > >> -------- > >> Just reports the fans are set to "-1" and refuses to change them. > >> (Yes, i8kmon is loaded.) > >> > >> > >> Tinkering with the /proc/ or /sys/ file system > >> ---------------------------------------------- > >> I don't have a /proc/acpi/fan directory. The directories > >> /sys/class/thermal/thermal_zone?/ appear to only describe a few heat > >> sensors on the motherboard (not the CPU temperatures reported by > >> coretemp) and I can't seem to modify the trip_point_0_temp files. > >> > >> The CPU temps reported by coretemp seem to live in > >> /sys/class/hwmon/hwmon1/device. If I attempt to change the max from > 95 > >> degrees C to 50 degrees C by running > >> > >> sudo bash -c "echo 50000 > > >> /sys/class/hwmon/hwmon1/device/temp2_max" > >> > >> I get the following error: > >> > >> bash: /sys/class/hwmon/hwmon1/device/temp2_max: Permission > denied > >> > >> When my CPU fan does run (i.e. when the CPU temp gets near to 105 > >> degrees C) nothing changes in > >> /sys/class/thermal/cooling_device?/cur_state. i.e. Linux doesn't > >> appear to acknowledge that the fan has started to run. > >> > >> Incidentally, Hardware Monitor (running under Windows) can't find my > >> CPU fan either (but the fan just magically works under Windows). So I > >> guess my fan isn't exposing itself very clearly to the OS. > >> > >> > >> Boot options > >> ------------ > >> The following all had no effect: > >> > >> - acpi.power_nocheck=1 > >> - acpi_osi=Linux > >> - acpi_osi=linux > >> - acpi_osi=Windows > >> - acpi=strict > >> > >> The only thing I tried which had any effect on my CPU fan was starting > >> with the boot option acpi=off. This allowed the fan to continue > >> spinning even while Ubuntu was running. But completely disabling ACPI > >> isn't a workable option for a production system. > >> > >> > >> Talking directly to the fan controller over I2C > >> ----------------------------------------------- > >> I guessed that my fan controller might be connected to the southbridge > >> via I2C. So I tinkered with i2c-tools but i2cdetect always complained > >> that the /dev/i2c-? files were not valid I2C devices. I tried loading > >> a number of i2c-related modules but to no avail. > >> > >> > >> What's controlling my CPU fan? The ACPI subsystem? > >> -------------------------------------------------- > >> The evidence is somewhat contradictory. On the one hand, setting the > >> boot option acpi=off successfully enables the fan, which suggests that > >> the ACPI subsystem is switching off my fan during a normal boot. On > >> the other hand, there's a bunch of evidence suggesting the fan isn't > >> controlled by ACPI on this laptop: > >> > >> I dissassembled my DSDT and found that PNP0c0b is not present (which > >> apparently is the code for a fan controller). Also, the evidence above > >> in the "Tinkering with the /proc/ or /sys/ file system" section would > >> suggest that my fan's controller isn't exposed over ACPI (or, > >> alternatively, it is exposed over ACPI but Linux doesn't know how to > >> handle it). > >> > >> I have noticed the following error in dmesg: [Firmware Bug]: ACPI: > >> BIOS _OSI(Linux) query ignored > >> > >> My full dmesg output is at the bottom of this email. > >> > >> > >> My guess at what's happening > >> ---------------------------- > >> This is total guess work but I think this is how it's working at the > >> moment: coretemp queries the CPU and finds that it can handle max > temp > >> (T_junction) of 105 degrees C. coretemp is not responsible for > >> controlling the fan (apparently) so some other subsystem (hwmon? acpi? > >> the BIOS?) must be taking the max temperatures stated by coretemp and > >> using these as the set points for the fan. > >> > >> > >> My system config > >> ---------------- > >> HP ProBook 6450b with 4GB of RAM and a magnetic hard disk. I'm running > >> the latest HP BIOS (version F.23, released 12 June 2012) > >> > >> CPU > >> - Name = Intel Core i5 450M. Two cores, each with 2 threads. > >> - Codename = Arrandale > >> - Specification = Intel(R) Core(TM) i5 CPU M 450 @ 2.40GHz > >> - Package (platform ID) = Socket 989 rPGA (0x4) > >> - CPUID = 6.5.5 > >> - Extended CPUID = 6.25 > >> - Core Stepping = K0 > >> > >> Chipset > >> - Northbridge = Intel Havendale/Clarkdale Host Bridge rev. 02 > >> - Southbridge = Intel HM57 rev. 05 > >> - Memory Type = DDR3 > >> > >> Monitoring > >> - Mainboard Model = 146D (0x000000DF - 0x00002220) > >> - LPCIO Vendor = SMSC > >> - LPCIO Vendor ID = 0x55 > >> - LPCIO Chip ID = 0x4C > >> > >> > >> > >> Summary > >> -------- > >> So, in summary: I'm 99% sure there's a bug in there somewhere. The fan > >> really, really should turn on long before the CPU gets anywhere near > >> 105 degrees C. I guess I have two questions: firstly, does anyone know > >> a fix?! If not, can anyone suggest any further diagnostic tests I can > >> run? > >> > >> > >> Warmest regards, > >> Jack > >> > >> > >> dmesg: > >> ------ > >> > >> [ 0.000000] Initializing cgroup subsys cpuset > >> [ 0.000000] Initializing cgroup subsys cpu > >> [ 0.000000] Linux version 3.2.0-31-generic (buildd@allspice) (gcc > >> version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #50-Ubuntu SMP Fri Sep > >> 7 16:16:45 UTC 2012 (Ubuntu 3.2.0-31.50-generic 3.2.28) > >> [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-31- > generic > >> root=UUID=f2ef5bd5-bb5d-484d-a638-ce1d9d6ac5e2 ro > >> [ 0.000000] KERNEL supported cpus: > >> [ 0.000000] Intel GenuineIntel > >> [ 0.000000] AMD AuthenticAMD > >> [ 0.000000] Centaur CentaurHauls > >> [ 0.000000] BIOS-provided physical RAM map: > >> [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) > >> [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) > >> [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 > (reserved) > >> [ 0.000000] BIOS-e820: 0000000000100000 - 00000000bafcf000 (usable) > >> [ 0.000000] BIOS-e820: 00000000bafcf000 - 00000000bb6cf000 (reserved) > >> [ 0.000000] BIOS-e820: 00000000bb6cf000 - 00000000bb7cf000 (ACPI > NVS) > >> [ 0.000000] BIOS-e820: 00000000bb7cf000 - 00000000bb7ff000 (ACPI > data) > >> [ 0.000000] BIOS-e820: 00000000bb7ff000 - 00000000bb800000 (usable) > >> [ 0.000000] BIOS-e820: 00000000bb800000 - 00000000bc000000 > (reserved) > >> [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 > (reserved) > >> [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) > >> [ 0.000000] BIOS-e820: 00000000fed10000 - 00000000fed14000 > (reserved) > >> [ 0.000000] BIOS-e820: 00000000fed19000 - 00000000fed1a000 > (reserved) > >> [ 0.000000] BIOS-e820: 00000000fed1b000 - 00000000fed20000 > (reserved) > >> [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 > (reserved) > >> [ 0.000000] BIOS-e820: 00000000ffd80000 - 0000000100000000 (reserved) > >> [ 0.000000] BIOS-e820: 0000000100000000 - 0000000138000000 (usable) > >> [ 0.000000] NX (Execute Disable) protection: active > >> [ 0.000000] DMI 2.6 present. > >> [ 0.000000] DMI: Hewlett-Packard HP ProBook 6450b/146D, BIOS 68CDE > >> Ver. F.23 06/13/2012 > >> [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 > >> (usable) ==> (reserved) > >> [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 > >> (usable) > >> [ 0.000000] No AGP bridge found > >> [ 0.000000] last_pfn = 0x138000 max_arch_pfn = 0x400000000 > >> [ 0.000000] MTRR default type: uncachable > >> [ 0.000000] MTRR fixed ranges enabled: > >> [ 0.000000] 00000-9FFFF write-back > >> [ 0.000000] A0000-BFFFF uncachable > >> [ 0.000000] C0000-FFFFF write-protect > >> [ 0.000000] MTRR variable ranges enabled: > >> [ 0.000000] 0 base 0FFC00000 mask FFFC00000 write-protect > >> [ 0.000000] 1 base 000000000 mask F80000000 write-back > >> [ 0.000000] 2 base 080000000 mask FC0000000 write-back > >> [ 0.000000] 3 base 0BC000000 mask FFC000000 uncachable > >> [ 0.000000] 4 base 100000000 mask FC0000000 write-back > >> [ 0.000000] 5 base 138000000 mask FF8000000 uncachable > >> [ 0.000000] 6 disabled > >> [ 0.000000] 7 disabled > >> [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new > >> 0x7010600070106 > >> [ 0.000000] last_pfn = 0xbb800 max_arch_pfn = 0x400000000 > >> [ 0.000000] initial memory mapped : 0 - 20000000 > >> [ 0.000000] Base memory trampoline at [ffff88000009a000] 9a000 size > 20480 > >> [ 0.000000] init_memory_mapping: 0000000000000000- > 00000000bb800000 > >> [ 0.000000] 0000000000 - 00bb800000 page 2M > >> [ 0.000000] kernel direct mapping tables up to bb800000 @ 1fffc000- > >> 20000000 > >> [ 0.000000] init_memory_mapping: 0000000100000000- > 0000000138000000 > >> [ 0.000000] 0100000000 - 0138000000 page 2M > >> [ 0.000000] kernel direct mapping tables up to 138000000 @ bafc9000- > >> bafcf000 > >> [ 0.000000] RAMDISK: 35848000 - 36c1c000 > >> [ 0.000000] ACPI: RSDP 00000000000fc600 00024 (v02 HPQOEM) > >> [ 0.000000] ACPI: XSDT 00000000bb7fe120 00084 (v01 HPQOEM SLIC-MPC > >> 0000000F 01000013) > >> [ 0.000000] ACPI: FACP 00000000bb7fc000 000F4 (v03 HPQOEM 146D > >> 0000000F HP 00000001) > >> [ 0.000000] ACPI: DSDT 00000000bb7d8000 1ED5E (v02 HPQOEM 146D > >> 00000001 INTL 20060912) > >> [ 0.000000] ACPI: FACS 00000000bb76d000 00040 > >> [ 0.000000] ACPI: HPET 00000000bb7fb000 00038 (v01 HPQOEM 146D > >> 00000001 HP 00000001) > >> [ 0.000000] ACPI: APIC 00000000bb7fa000 000BC (v01 HPQOEM 146D > >> 00000001 HP 00000001) > >> [ 0.000000] ACPI: MCFG 00000000bb7f9000 0003C (v01 HPQOEM 146D > >> 00000001 HP 00000001) > >> [ 0.000000] ACPI: ASF! 00000000bb7f8000 000A0 (v32 HPQOEM 146D > >> 00000001 HP 00000001) > >> [ 0.000000] ACPI: TCPA 00000000bb7f7000 00032 (v02 HPQOEM 146D > >> 00000000 HP 00000001) > >> [ 0.000000] ACPI: SSDT 00000000bb7d5000 00135 (v01 HPQOEM SataAhci > >> 00001000 INTL 20060912) > >> [ 0.000000] ACPI: SSDT 00000000bb7d4000 00314 (v01 HPQOEM PtidDevc > >> 00001000 INTL 20060912) > >> [ 0.000000] ACPI: SLIC 00000000bb7d3000 00176 (v01 HPQOEM SLIC-MPC > >> 00000001 HP 00000001) > >> [ 0.000000] ACPI: SSDT 00000000bb7d2000 00A10 (v01 PmRef CpuPm > >> 00003000 INTL 20060912) > >> [ 0.000000] ACPI: SSDT 00000000bb7d1000 00288 (v01 PmRef Cpu0Tst > >> 00003000 INTL 20060912) > >> [ 0.000000] ACPI: SSDT 00000000bb7d0000 00225 (v01 PmRef ApTst > >> 00003000 INTL 20060912) > >> [ 0.000000] ACPI: Local APIC address 0xfee00000 > >> [ 0.000000] No NUMA configuration found > >> [ 0.000000] Faking a node at 0000000000000000-0000000138000000 > >> [ 0.000000] Initmem setup node 0 0000000000000000-0000000138000000 > >> [ 0.000000] NODE_DATA [0000000137ffb000 - 0000000137ffffff] > >> [ 0.000000] [ffffea0000000000-ffffea0004dfffff] PMD -> > >> [ffff880133800000-ffff8801375fffff] on node 0 > >> [ 0.000000] Zone PFN ranges: > >> [ 0.000000] DMA 0x00000010 -> 0x00001000 > >> [ 0.000000] DMA32 0x00001000 -> 0x00100000 > >> [ 0.000000] Normal 0x00100000 -> 0x00138000 > >> [ 0.000000] Movable zone start PFN for each node > >> [ 0.000000] early_node_map[4] active PFN ranges > >> [ 0.000000] 0: 0x00000010 -> 0x0000009f > >> [ 0.000000] 0: 0x00000100 -> 0x000bafcf > >> [ 0.000000] 0: 0x000bb7ff -> 0x000bb800 > >> [ 0.000000] 0: 0x00100000 -> 0x00138000 > >> [ 0.000000] On node 0 totalpages: 995167 > >> [ 0.000000] DMA zone: 64 pages used for memmap > >> [ 0.000000] DMA zone: 5 pages reserved > >> [ 0.000000] DMA zone: 3914 pages, LIFO batch:0 > >> [ 0.000000] DMA32 zone: 16320 pages used for memmap > >> [ 0.000000] DMA32 zone: 745488 pages, LIFO batch:31 > >> [ 0.000000] Normal zone: 3584 pages used for memmap > >> [ 0.000000] Normal zone: 225792 pages, LIFO batch:31 > >> [ 0.000000] ACPI: PM-Timer IO Port: 0x408 > >> [ 0.000000] ACPI: Local APIC address 0xfee00000 > >> [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) > >> [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) > >> [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x04] enabled) > >> [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x05] enabled) > >> [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x00] disabled) > >> [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled) > >> [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled) > >> [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled) > >> [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) > >> [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) > >> [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) > >> [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) > >> [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1]) > >> [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1]) > >> [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1]) > >> [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1]) > >> [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) > >> [ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 > >> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > >> [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) > >> [ 0.000000] ACPI: IRQ0 used by override. > >> [ 0.000000] ACPI: IRQ2 used by override. > >> [ 0.000000] ACPI: IRQ9 used by override. > >> [ 0.000000] Using ACPI (MADT) for SMP configuration information > >> [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000 > >> [ 0.000000] SMP: Allowing 8 CPUs, 4 hotplug CPUs > >> [ 0.000000] nr_irqs_gsi: 40 > >> [ 0.000000] PM: Registered nosave memory: 000000000009f000 - > >> 00000000000a0000 > >> [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - > >> 00000000000e0000 > >> [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - > >> 0000000000100000 > >> [ 0.000000] PM: Registered nosave memory: 00000000bafcf000 - > >> 00000000bb6cf000 > >> [ 0.000000] PM: Registered nosave memory: 00000000bb6cf000 - > >> 00000000bb7cf000 > >> [ 0.000000] PM: Registered nosave memory: 00000000bb7cf000 - > >> 00000000bb7ff000 > >> [ 0.000000] PM: Registered nosave memory: 00000000bb800000 - > >> 00000000bc000000 > >> [ 0.000000] PM: Registered nosave memory: 00000000bc000000 - > >> 00000000e0000000 > >> [ 0.000000] PM: Registered nosave memory: 00000000e0000000 - > >> 00000000f0000000 > >> [ 0.000000] PM: Registered nosave memory: 00000000f0000000 - > >> 00000000fec00000 > >> [ 0.000000] PM: Registered nosave memory: 00000000fec00000 - > >> 00000000fec01000 > >> [ 0.000000] PM: Registered nosave memory: 00000000fec01000 - > >> 00000000fed10000 > >> [ 0.000000] PM: Registered nosave memory: 00000000fed10000 - > >> 00000000fed14000 > >> [ 0.000000] PM: Registered nosave memory: 00000000fed14000 - > >> 00000000fed19000 > >> [ 0.000000] PM: Registered nosave memory: 00000000fed19000 - > >> 00000000fed1a000 > >> [ 0.000000] PM: Registered nosave memory: 00000000fed1a000 - > >> 00000000fed1b000 > >> [ 0.000000] PM: Registered nosave memory: 00000000fed1b000 - > >> 00000000fed20000 > >> [ 0.000000] PM: Registered nosave memory: 00000000fed20000 - > >> 00000000fee00000 > >> [ 0.000000] PM: Registered nosave memory: 00000000fee00000 - > >> 00000000fee01000 > >> [ 0.000000] PM: Registered nosave memory: 00000000fee01000 - > >> 00000000ffd80000 > >> [ 0.000000] PM: Registered nosave memory: 00000000ffd80000 - > >> 0000000100000000 > >> [ 0.000000] Allocating PCI resources starting at bc000000 (gap: > >> bc000000:24000000) > >> [ 0.000000] Booting paravirtualized kernel on bare hardware > >> [ 0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 > >> nr_cpu_ids:8 nr_node_ids:1 > >> [ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff880137c00000 s83136 > >> r8192 d23360 u262144 > >> [ 0.000000] pcpu-alloc: s83136 r8192 d23360 u262144 alloc=1*2097152 > >> [ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7 > >> [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. > >> Total pages: 975194 > >> [ 0.000000] Policy zone: Normal > >> [ 0.000000] Kernel command line: > >> BOOT_IMAGE=/boot/vmlinuz-3.2.0-31-generic > >> root=UUID=f2ef5bd5-bb5d-484d-a638-ce1d9d6ac5e2 ro > >> [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) > >> [ 0.000000] Checking aperture... > >> [ 0.000000] No AGP bridge found > >> [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area > >> [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing! > >> [ 0.000000] Memory: 3814096k/5111808k available (6558k kernel code, > >> 1131140k absent, 166572k reserved, 6642k data, 920k init) > >> [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, > >> CPUs=8, Nodes=1 > >> [ 0.000000] Hierarchical RCU implementation. > >> [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled. > >> [ 0.000000] NR_IRQS:16640 nr_irqs:744 16 > >> [ 0.000000] Extended CMOS year: 2000 > >> [ 0.000000] Console: colour VGA+ 80x25 > >> [ 0.000000] console [tty0] enabled > >> [ 0.000000] allocated 32505856 bytes of page_cgroup > >> [ 0.000000] please try 'cgroup_disable=memory' option if you don't > >> want memory cgroups > >> [ 0.000000] hpet clockevent registered > >> [ 0.000000] Fast TSC calibration using PIT > >> [ 0.004000] Detected 2393.981 MHz processor. > >> [ 0.000003] Calibrating delay loop (skipped), value calculated > >> using timer frequency.. 4787.96 BogoMIPS (lpj=9575924) > >> [ 0.000121] pid_max: default: 32768 minimum: 301 > >> [ 0.000198] Security Framework initialized > >> [ 0.000265] AppArmor: AppArmor initialized > >> [ 0.000319] Yama: becoming mindful. > >> [ 0.000673] Dentry cache hash table entries: 524288 (order: 10, > >> 4194304 bytes) > >> [ 0.001694] Inode-cache hash table entries: 262144 (order: 9, 2097152 > bytes) > >> [ 0.002166] Mount-cache hash table entries: 256 > >> [ 0.002337] Initializing cgroup subsys cpuacct > >> [ 0.002396] Initializing cgroup subsys memory > >> [ 0.002455] Initializing cgroup subsys devices > >> [ 0.002511] Initializing cgroup subsys freezer > >> [ 0.002566] Initializing cgroup subsys blkio > >> [ 0.002624] Initializing cgroup subsys perf_event > >> [ 0.002706] CPU: Physical Processor ID: 0 > >> [ 0.002761] CPU: Processor Core ID: 0 > >> [ 0.002818] mce: CPU supports 9 MCE banks > >> [ 0.002881] CPU0: Thermal monitoring enabled (TM1) > >> [ 0.002943] using mwait in idle threads. > >> [ 0.005022] ACPI: Core revision 20110623 > >> [ 0.013522] ftrace: allocating 27008 entries in 106 pages > >> [ 0.021702] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 > >> [ 0.061387] CPU0: Intel(R) Core(TM) i5 CPU M 450 @ 2.40GHz > stepping > >> 05 > >> [ 0.167594] Performance Events: PEBS fmt1+, Westmere events, Intel > >> PMU driver. > >> [ 0.167766] ... version: 3 > >> [ 0.167827] ... bit width: 48 > >> [ 0.167888] ... generic registers: 4 > >> [ 0.167948] ... value mask: 0000ffffffffffff > >> [ 0.168012] ... max period: 000000007fffffff > >> [ 0.168077] ... fixed-purpose events: 3 > >> [ 0.168138] ... event mask: 000000070000000f > >> [ 0.168399] NMI watchdog enabled, takes one hw-pmu counter. > >> [ 0.168544] Booting Node 0, Processors #1 > >> [ 0.168607] smpboot cpu 1: start_ip = 9a000 > >> [ 0.279519] NMI watchdog enabled, takes one hw-pmu counter. > >> [ 0.279701] #2 > >> [ 0.279731] smpboot cpu 2: start_ip = 9a000 > >> [ 0.387295] NMI watchdog enabled, takes one hw-pmu counter. > >> [ 0.387461] #3 > >> [ 0.387491] smpboot cpu 3: start_ip = 9a000 > >> [ 0.495140] NMI watchdog enabled, takes one hw-pmu counter. > >> [ 0.495251] Brought up 4 CPUs > >> [ 0.495310] Total of 4 processors activated (19151.64 BogoMIPS). > >> [ 0.498269] devtmpfs: initialized > >> [ 0.499160] EVM: security.selinux > >> [ 0.499220] EVM: security.SMACK64 > >> [ 0.499278] EVM: security.capability > >> [ 0.499949] PM: Registering ACPI NVS region at bb6cf000 (1048576 bytes) > >> [ 0.500804] print_constraints: dummy: > >> [ 0.500894] RTC time: 9:18:08, date: 09/24/12 > >> [ 0.500987] NET: Registered protocol family 16 > >> [ 0.501147] Trying to unpack rootfs image as initramfs... > >> [ 0.501152] ACPI FADT declares the system doesn't support PCIe > >> ASPM, so disable it > >> [ 0.501154] ACPI: bus type pci registered > >> [ 0.501226] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem > >> 0xe0000000-0xefffffff] (base 0xe0000000) > >> [ 0.501228] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in > >> E820 > >> [ 0.532935] PCI: Using configuration type 1 for base access > >> [ 0.533855] bio: create slab <bio-0> at 0 > >> [ 0.534001] ACPI: Added _OSI(Module Device) > >> [ 0.534061] ACPI: Added _OSI(Processor Device) > >> [ 0.534122] ACPI: Added _OSI(3.0 _SCP Extensions) > >> [ 0.534183] ACPI: Added _OSI(Processor Aggregator Device) > >> [ 0.536028] ACPI: EC: Look up EC in DSDT > >> [ 0.560438] ACPI: Executed 1 blocks of module-level executable AML > code > >> [ 0.602925] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored > >> [ 0.644497] ACPI: SSDT 00000000bb6c8918 003F9 (v01 PmRef Cpu0Ist > >> 00003000 INTL 20060912) > >> [ 0.645076] ACPI: Dynamic OEM Table Load: > >> [ 0.645184] ACPI: SSDT (null) 003F9 (v01 PmRef Cpu0Ist > >> 00003000 INTL 20060912) > >> [ 0.645449] ACPI: SSDT 00000000bb6c6018 008AA (v01 PmRef Cpu0Cst > >> 00003001 INTL 20060912) > >> [ 0.646006] ACPI: Dynamic OEM Table Load: > >> [ 0.646114] ACPI: SSDT (null) 008AA (v01 PmRef Cpu0Cst > >> 00003001 INTL 20060912) > >> [ 0.690959] ACPI: SSDT 00000000bb6c7a98 00303 (v01 PmRef ApIst > >> 00003000 INTL 20060912) > >> [ 0.691576] ACPI: Dynamic OEM Table Load: > >> [ 0.691685] ACPI: SSDT (null) 00303 (v01 PmRef ApIst > >> 00003000 INTL 20060912) > >> [ 0.714785] ACPI: SSDT 00000000bb6c5d98 00119 (v01 PmRef ApCst > >> 00003000 INTL 20060912) > >> [ 0.715371] ACPI: Dynamic OEM Table Load: > >> [ 0.715479] ACPI: SSDT (null) 00119 (v01 PmRef ApCst > >> 00003000 INTL 20060912) > >> [ 0.827677] Freeing initrd memory: 20304k freed > >> [ 1.165720] ACPI: Interpreter enabled > >> [ 1.165789] ACPI: (supports S0 S3 S4 S5) > >> [ 1.165968] ACPI: Using IOAPIC for interrupt routing > >> [ 1.167597] ACPI: Power Resource [APPR] (off) > >> [ 1.180859] ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = > 0x62 > >> [ 1.181103] ACPI: No dock devices found. > >> [ 1.181164] HEST: Table not found. > >> [ 1.181225] PCI: Using host bridge windows from ACPI; if necessary, > >> use "pci=nocrs" and report a bug > >> [ 1.182002] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe]) > >> [ 1.182638] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7] > >> [ 1.182709] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff] > >> [ 1.182778] pci_root PNP0A08:00: host bridge window [mem > >> 0x000a0000-0x000bffff] > >> [ 1.182875] pci_root PNP0A08:00: host bridge window [mem > >> 0xc0000000-0xdfffffff] > >> [ 1.182971] pci_root PNP0A08:00: host bridge window [mem > >> 0xf0000000-0xfedfffff] > >> [ 1.183067] pci_root PNP0A08:00: host bridge window [mem > >> 0xfee01000-0xffffffff] > >> [ 1.183173] pci 0000:00:00.0: [8086:0044] type 0 class 0x000600 > >> [ 1.183191] DMAR: BIOS has allocated no shadow GTT; disabling IOMMU > >> for graphics > >> [ 1.183307] pci 0000:00:02.0: [8086:0046] type 0 class 0x000300 > >> [ 1.183317] pci 0000:00:02.0: reg 10: [mem 0xd0000000-0xd03fffff 64bit] > >> [ 1.183323] pci 0000:00:02.0: reg 18: [mem 0xc0000000-0xcfffffff 64bit > pref] > >> [ 1.183327] pci 0000:00:02.0: reg 20: [io 0x4050-0x4057] > >> [ 1.183390] pci 0000:00:16.0: [8086:3b64] type 0 class 0x000780 > >> [ 1.183418] pci 0000:00:16.0: reg 10: [mem 0xd4824000-0xd482400f 64bit] > >> [ 1.183509] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold > >> [ 1.183514] pci 0000:00:16.0: PME# disabled > >> [ 1.183552] pci 0000:00:19.0: [8086:10eb] type 0 class 0x000200 > >> [ 1.183576] pci 0000:00:19.0: reg 10: [mem 0xd4800000-0xd481ffff] > >> [ 1.183587] pci 0000:00:19.0: reg 14: [mem 0xd482a000-0xd482afff] > >> [ 1.183599] pci 0000:00:19.0: reg 18: [io 0x4020-0x403f] > >> [ 1.183686] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold > >> [ 1.183690] pci 0000:00:19.0: PME# disabled > >> [ 1.183719] pci 0000:00:1a.0: [8086:3b3c] type 0 class 0x000c03 > >> [ 1.183743] pci 0000:00:1a.0: reg 10: [mem 0xd4829000-0xd48293ff] > >> [ 1.183849] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold > >> [ 1.183854] pci 0000:00:1a.0: PME# disabled > >> [ 1.183884] pci 0000:00:1b.0: [8086:3b56] type 0 class 0x000403 > >> [ 1.183904] pci 0000:00:1b.0: reg 10: [mem 0xd4820000-0xd4823fff 64bit] > >> [ 1.183999] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold > >> [ 1.184004] pci 0000:00:1b.0: PME# disabled > >> [ 1.184031] pci 0000:00:1c.0: [8086:3b42] type 1 class 0x000604 > >> [ 1.184130] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold > >> [ 1.184134] pci 0000:00:1c.0: PME# disabled > >> [ 1.184163] pci 0000:00:1c.1: [8086:3b44] type 1 class 0x000604 > >> [ 1.184261] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold > >> [ 1.184266] pci 0000:00:1c.1: PME# disabled > >> [ 1.184297] pci 0000:00:1c.2: [8086:3b46] type 1 class 0x000604 > >> [ 1.184395] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold > >> [ 1.184400] pci 0000:00:1c.2: PME# disabled > >> [ 1.184428] pci 0000:00:1c.3: [8086:3b48] type 1 class 0x000604 > >> [ 1.184527] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold > >> [ 1.184531] pci 0000:00:1c.3: PME# disabled > >> [ 1.184569] pci 0000:00:1d.0: [8086:3b34] type 0 class 0x000c03 > >> [ 1.184593] pci 0000:00:1d.0: reg 10: [mem 0xd4828000-0xd48283ff] > >> [ 1.184701] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold > >> [ 1.184705] pci 0000:00:1d.0: PME# disabled > >> [ 1.184729] pci 0000:00:1e.0: [8086:2448] type 1 class 0x000604 > >> [ 1.184814] pci 0000:00:1f.0: [8086:3b0b] type 0 class 0x000601 > >> [ 1.184941] pci 0000:00:1f.2: [8086:3b2f] type 0 class 0x000106 > >> [ 1.184967] pci 0000:00:1f.2: reg 10: [io 0x4048-0x404f] > >> [ 1.184978] pci 0000:00:1f.2: reg 14: [io 0x405c-0x405f] > >> [ 1.184988] pci 0000:00:1f.2: reg 18: [io 0x4040-0x4047] > >> [ 1.184999] pci 0000:00:1f.2: reg 1c: [io 0x4058-0x405b] > >> [ 1.185010] pci 0000:00:1f.2: reg 20: [io 0x4000-0x401f] > >> [ 1.185020] pci 0000:00:1f.2: reg 24: [mem 0xd4827000-0xd48277ff] > >> [ 1.185086] pci 0000:00:1f.2: PME# supported from D3hot > >> [ 1.185091] pci 0000:00:1f.2: PME# disabled > >> [ 1.185123] pci 0000:00:1f.6: [8086:3b32] type 0 class 0x001180 > >> [ 1.185150] pci 0000:00:1f.6: reg 10: [mem 0xd4826000-0xd4826fff 64bit] > >> [ 1.185301] pci 0000:00:1c.0: PCI bridge to [bus 01-01] > >> [ 1.185371] pci 0000:00:1c.0: bridge window [mem 0xd4700000- > 0xd47fffff] > >> [ 1.185431] pci 0000:00:1c.1: PCI bridge to [bus 02-42] > >> [ 1.185498] pci 0000:00:1c.1: bridge window [io 0x2000-0x3fff] > >> [ 1.185503] pci 0000:00:1c.1: bridge window [mem 0xd0700000- > 0xd46fffff] > >> [ 1.185618] pci 0000:43:00.0: [1180:e822] type 0 class 0x000805 > >> [ 1.185640] pci 0000:43:00.0: reg 10: [mem 0xd0603000-0xd06030ff] > >> [ 1.185800] pci 0000:43:00.0: supports D1 D2 > >> [ 1.185802] pci 0000:43:00.0: PME# supported from D0 D1 D2 D3hot > D3cold > >> [ 1.185808] pci 0000:43:00.0: PME# disabled > >> [ 1.185862] pci 0000:43:00.1: [1180:e230] type 0 class 0x000880 > >> [ 1.185884] pci 0000:43:00.1: reg 10: [mem 0xd0602000-0xd06020ff] > >> [ 1.186048] pci 0000:43:00.1: supports D1 D2 > >> [ 1.186049] pci 0000:43:00.1: PME# supported from D0 D1 D2 D3hot > D3cold > >> [ 1.186055] pci 0000:43:00.1: PME# disabled > >> [ 1.186102] pci 0000:43:00.2: [1180:e852] type 0 class 0x000880 > >> [ 1.186124] pci 0000:43:00.2: reg 10: [mem 0xd0601000-0xd06010ff] > >> [ 1.186284] pci 0000:43:00.2: supports D1 D2 > >> [ 1.186286] pci 0000:43:00.2: PME# supported from D0 D1 D2 D3hot > D3cold > >> [ 1.186292] pci 0000:43:00.2: PME# disabled > >> [ 1.186338] pci 0000:43:00.3: [1180:e832] type 0 class 0x000c00 > >> [ 1.186360] pci 0000:43:00.3: reg 10: [mem 0xd0600000-0xd06007ff] > >> [ 1.186521] pci 0000:43:00.3: supports D1 D2 > >> [ 1.186523] pci 0000:43:00.3: PME# supported from D0 D1 D2 D3hot > D3cold > >> [ 1.186529] pci 0000:43:00.3: PME# disabled > >> [ 1.193984] pci 0000:00:1c.2: PCI bridge to [bus 43-43] > >> [ 1.194059] pci 0000:00:1c.2: bridge window [mem 0xd0600000- > 0xd06fffff] > >> [ 1.194179] pci 0000:44:00.0: [14e4:4727] type 0 class 0x000280 > >> [ 1.194210] pci 0000:44:00.0: reg 10: [mem 0xd0500000-0xd0503fff 64bit] > >> [ 1.194368] pci 0000:44:00.0: supports D1 D2 > >> [ 1.201943] pci 0000:00:1c.3: PCI bridge to [bus 44-44] > >> [ 1.202013] pci 0000:00:1c.3: bridge window [mem 0xd0500000- > 0xd05fffff] > >> [ 1.202092] pci 0000:00:1e.0: PCI bridge to [bus 45-45] (subtractive > decode) > >> [ 1.202167] pci 0000:00:1e.0: bridge window [mem 0xd0400000- > 0xd04fffff] > >> [ 1.202175] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] > >> (subtractive decode) > >> [ 1.202176] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] > >> (subtractive decode) > >> [ 1.202178] pci 0000:00:1e.0: bridge window [mem > >> 0x000a0000-0x000bffff] (subtractive decode) > >> [ 1.202180] pci 0000:00:1e.0: bridge window [mem > >> 0xc0000000-0xdfffffff] (subtractive decode) > >> [ 1.202182] pci 0000:00:1e.0: bridge window [mem > >> 0xf0000000-0xfedfffff] (subtractive decode) > >> [ 1.202184] pci 0000:00:1e.0: bridge window [mem > >> 0xfee01000-0xffffffff] (subtractive decode) > >> [ 1.202215] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > >> [ 1.202409] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT] > >> [ 1.202455] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT] > >> [ 1.202482] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT] > >> [ 1.202529] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT] > >> [ 1.202569] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT] > >> [ 1.202951] pci0000:00: Requesting ACPI _OSC control (0x1d) > >> [ 1.204015] pci0000:00: ACPI _OSC control (0x1d) granted > >> [ 1.209353] ACPI: PCI Root Bridge [CPBG] (domain 0000 [bus ff]) > >> [ 1.209481] pci 0000:ff:00.0: [8086:2c62] type 0 class 0x000600 > >> [ 1.209499] pci 0000:ff:00.1: [8086:2d01] type 0 class 0x000600 > >> [ 1.209518] pci 0000:ff:02.0: [8086:2d10] type 0 class 0x000600 > >> [ 1.209534] pci 0000:ff:02.1: [8086:2d11] type 0 class 0x000600 > >> [ 1.209551] pci 0000:ff:02.2: [8086:2d12] type 0 class 0x000600 > >> [ 1.209566] pci 0000:ff:02.3: [8086:2d13] type 0 class 0x000600 > >> [ 1.209595] pci0000:ff: Requesting ACPI _OSC control (0x1d) > >> [ 1.209663] pci0000:ff: ACPI _OSC request failed (AE_NOT_FOUND), > >> returned control mask: 0x1d > >> [ 1.209762] ACPI _OSC control for PCIe not granted, disabling ASPM > >> [ 1.210028] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 12 14 15) > >> [ 1.210422] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 *5 6 7 11 12 14 15) > >> [ 1.210813] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15) > >> [ 1.211206] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 > >> 14 15) *10 > >> [ 1.211647] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 *10 12 14 15) > >> [ 1.212040] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15) > >> [ 1.212432] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 > >> 14 15) *0, disabled. > >> [ 1.212900] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 > >> 14 15) *0, disabled. > >> [ 1.213431] vgaarb: device added: > >> PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none > >> [ 1.213535] vgaarb: loaded > >> [ 1.213592] vgaarb: bridge control possible 0000:00:02.0 > >> [ 1.213742] i2c-core: driver [aat2870] using legacy suspend method > >> [ 1.213811] i2c-core: driver [aat2870] using legacy resume method > >> [ 1.213936] SCSI subsystem initialized > >> [ 1.214053] libata version 3.00 loaded. > >> [ 1.214091] usbcore: registered new interface driver usbfs > >> [ 1.214164] usbcore: registered new interface driver hub > >> [ 1.214252] usbcore: registered new device driver usb > >> [ 1.214388] PCI: Using ACPI for IRQ routing > >> [ 1.224312] PCI: pci_cache_line_size set to 64 bytes > >> [ 1.224398] reserve RAM buffer: 000000000009fc00 - 000000000009ffff > >> [ 1.224400] reserve RAM buffer: 00000000bafcf000 - 00000000bbffffff > >> [ 1.224402] reserve RAM buffer: 00000000bb800000 - 00000000bbffffff > >> [ 1.224487] NetLabel: Initializing > >> [ 1.224546] NetLabel: domain hash size = 128 > >> [ 1.224602] NetLabel: protocols = UNLABELED CIPSOv4 > >> [ 1.224672] NetLabel: unlabeled traffic allowed by default > >> [ 1.224784] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0 > >> [ 1.225071] hpet0: 8 comparators, 64-bit 14.318180 MHz counter > >> [ 1.227154] Switching to clocksource hpet > >> [ 1.232742] AppArmor: AppArmor Filesystem Enabled > >> [ 1.232838] pnp: PnP ACPI init > >> [ 1.232912] ACPI: bus type pnp registered > >> [ 1.233323] pnp 00:00: [bus 00-fe] > >> [ 1.233326] pnp 00:00: [io 0x0000-0x0cf7 window] > >> [ 1.233327] pnp 00:00: [io 0x0cf8-0x0cff] > >> [ 1.233329] pnp 00:00: [io 0x0d00-0xffff window] > >> [ 1.233331] pnp 00:00: [mem 0x000a0000-0x000bffff window] > >> [ 1.233332] pnp 00:00: [mem 0x000c0000-0x000c3fff window] > >> [ 1.233334] pnp 00:00: [mem 0x000c4000-0x000c7fff window] > >> [ 1.233335] pnp 00:00: [mem 0x000c8000-0x000cbfff window] > >> [ 1.233337] pnp 00:00: [mem 0x000cc000-0x000cffff window] > >> [ 1.233338] pnp 00:00: [mem 0x000d0000-0x000d3fff window] > >> [ 1.233340] pnp 00:00: [mem 0x000d4000-0x000d7fff window] > >> [ 1.233341] pnp 00:00: [mem 0x000d8000-0x000dbfff window] > >> [ 1.233343] pnp 00:00: [mem 0x000dc000-0x000dffff window] > >> [ 1.233345] pnp 00:00: [mem 0x000e0000-0x000e3fff window] > >> [ 1.233346] pnp 00:00: [mem 0x000e4000-0x000e7fff window] > >> [ 1.233348] pnp 00:00: [mem 0x000e8000-0x000ebfff window] > >> [ 1.233349] pnp 00:00: [mem 0x000ec000-0x000effff window] > >> [ 1.233351] pnp 00:00: [mem 0x000f0000-0x000fffff window] > >> [ 1.233352] pnp 00:00: [mem 0xc0000000-0xdfffffff window] > >> [ 1.233354] pnp 00:00: [mem 0xf0000000-0xfedfffff window] > >> [ 1.233356] pnp 00:00: [mem 0xfee01000-0xffffffff window] > >> [ 1.233448] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 > >> PNP0a03 (active) > >> [ 1.233621] pnp 00:01: [mem 0xfed1c000-0xfed1ffff] > >> [ 1.233623] pnp 00:01: [mem 0xfed10000-0xfed13fff] > >> [ 1.233624] pnp 00:01: [mem 0xfed1b000-0xfed1bfff] > >> [ 1.233626] pnp 00:01: [mem 0xfed19000-0xfed19fff] > >> [ 1.233627] pnp 00:01: [mem 0xd4900000-0xd4900fff] > >> [ 1.233629] pnp 00:01: [mem 0xe0000000-0xefffffff] > >> [ 1.233630] pnp 00:01: [mem 0xfed20000-0xfed3ffff] > >> [ 1.233632] pnp 00:01: [mem 0xfed90000-0xfed8ffff disabled] > >> [ 1.233633] pnp 00:01: [mem 0xfed45000-0xfed8ffff] > >> [ 1.233635] pnp 00:01: [mem 0xfec00000-0xfec00fff] > >> [ 1.233687] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been > reserved > >> [ 1.233758] system 00:01: [mem 0xfed10000-0xfed13fff] has been > reserved > >> [ 1.233827] system 00:01: [mem 0xfed1b000-0xfed1bfff] has been > reserved > >> [ 1.233897] system 00:01: [mem 0xfed19000-0xfed19fff] has been > reserved > >> [ 1.233966] system 00:01: [mem 0xd4900000-0xd4900fff] has been > reserved > >> [ 1.234035] system 00:01: [mem 0xe0000000-0xefffffff] has been > reserved > >> [ 1.234105] system 00:01: [mem 0xfed20000-0xfed3ffff] has been > reserved > >> [ 1.234175] system 00:01: [mem 0xfed45000-0xfed8ffff] has been > reserved > >> [ 1.234245] system 00:01: [mem 0xfec00000-0xfec00fff] could not be > >> reserved > >> [ 1.234316] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active) > >> [ 1.234382] pnp 00:02: [io 0x0000-0x001f] > >> [ 1.234384] pnp 00:02: [io 0x0081-0x0091] > >> [ 1.234387] pnp 00:02: [io 0x0093-0x009f] > >> [ 1.234388] pnp 00:02: [io 0x00c0-0x00df] > >> [ 1.234390] pnp 00:02: [dma 4] > >> [ 1.234418] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active) > >> [ 1.234425] pnp 00:03: [mem 0xff000000-0xffffffff] > >> [ 1.234449] pnp 00:03: Plug and Play ACPI device, IDs INT0800 (active) > >> [ 1.234492] pnp 00:04: [io 0xfe00-0xfe0f] > >> [ 1.234494] pnp 00:04: [io 0xfe80-0xfe8f] > >> [ 1.234495] pnp 00:04: [mem 0xfed40000-0xfed44fff] > >> [ 1.234526] pnp 00:04: Plug and Play ACPI device, IDs IFX0102 > >> PNP0c31 (active) > >> [ 1.234592] pnp 00:05: [mem 0xfed00000-0xfed003ff] > >> [ 1.234622] pnp 00:05: Plug and Play ACPI device, IDs PNP0103 (active) > >> [ 1.234630] pnp 00:06: [io 0x00f0] > >> [ 1.234642] pnp 00:06: [irq 13] > >> [ 1.234668] pnp 00:06: Plug and Play ACPI device, IDs PNP0c04 (active) > >> [ 1.234676] pnp 00:07: [io 0x002e-0x002f] > >> [ 1.234678] pnp 00:07: [io 0x004e-0x004f] > >> [ 1.234679] pnp 00:07: [io 0x0061] > >> [ 1.234680] pnp 00:07: [io 0x0063] > >> [ 1.234681] pnp 00:07: [io 0x0065] > >> [ 1.234683] pnp 00:07: [io 0x0067] > >> [ 1.234684] pnp 00:07: [io 0x0070] > >> [ 1.234685] pnp 00:07: [io 0x0080] > >> [ 1.234686] pnp 00:07: [io 0x0092] > >> [ 1.234688] pnp 00:07: [io 0x00b2-0x00b3] > >> [ 1.234689] pnp 00:07: [io 0x0200-0x027f] > >> [ 1.234690] pnp 00:07: [io 0x1000-0x100f] > >> [ 1.234691] pnp 00:07: [io 0xffff] > >> [ 1.234693] pnp 00:07: [io 0xffff] > >> [ 1.234694] pnp 00:07: [io 0x0400-0x047f] > >> [ 1.234695] pnp 00:07: [io 0x0500-0x057f] > >> [ 1.234697] pnp 00:07: [io 0xef80-0xef9f] > >> [ 1.234741] system 00:07: [io 0x0200-0x027f] has been reserved > >> [ 1.234808] system 00:07: [io 0x1000-0x100f] has been reserved > >> [ 1.234875] system 00:07: [io 0xffff] has been reserved > >> [ 1.234941] system 00:07: [io 0xffff] has been reserved > >> [ 1.235005] system 00:07: [io 0x0400-0x047f] has been reserved > >> [ 1.235073] system 00:07: [io 0x0500-0x057f] has been reserved > >> [ 1.235140] system 00:07: [io 0xef80-0xef9f] has been reserved > >> [ 1.235223] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active) > >> [ 1.235230] pnp 00:08: [io 0x0070-0x0077] > >> [ 1.235236] pnp 00:08: [irq 8] > >> [ 1.235266] pnp 00:08: Plug and Play ACPI device, IDs PNP0b00 (active) > >> [ 1.235378] pnp 00:09: [io 0x0060] > >> [ 1.235380] pnp 00:09: [io 0x0064] > >> [ 1.235386] pnp 00:09: [irq 1] > >> [ 1.235420] pnp 00:09: Plug and Play ACPI device, IDs PNP0303 (active) > >> [ 1.235431] pnp 00:0a: [irq 12] > >> [ 1.235459] pnp 00:0a: Plug and Play ACPI device, IDs SYN0179 > >> SYN0100 SYN0002 PNP0f13 (active) > >> [ 1.235658] pnp 00:0b: [irq 23] > >> [ 1.235696] pnp 00:0b: Plug and Play ACPI device, IDs HPQ0004 (active) > >> [ 1.235808] pnp 00:0c: [bus ff] > >> [ 1.235848] pnp 00:0c: Plug and Play ACPI device, IDs PNP0a03 (active) > >> [ 1.235958] pnp: PnP ACPI: found 13 devices > >> [ 1.236019] ACPI: ACPI bus type pnp unregistered > >> [ 1.242789] PCI: max bus depth: 1 pci_try_num: 2 > >> [ 1.242843] pci 0000:00:1c.1: BAR 15: assigned [mem > >> 0xd4a00000-0xd4bfffff 64bit pref] > >> [ 1.242939] pci 0000:00:1c.0: PCI bridge to [bus 01-01] > >> [ 1.243008] pci 0000:00:1c.0: bridge window [mem 0xd4700000- > 0xd47fffff] > >> [ 1.243086] pci 0000:00:1c.1: PCI bridge to [bus 02-42] > >> [ 1.243161] pci 0000:00:1c.1: bridge window [io 0x2000-0x3fff] > >> [ 1.243233] pci 0000:00:1c.1: bridge window [mem 0xd0700000- > 0xd46fffff] > >> [ 1.243305] pci 0000:00:1c.1: bridge window [mem > >> 0xd4a00000-0xd4bfffff 64bit pref] > >> [ 1.243407] pci 0000:00:1c.2: PCI bridge to [bus 43-43] > >> [ 1.243475] pci 0000:00:1c.2: bridge window [mem 0xd0600000- > 0xd06fffff] > >> [ 1.243553] pci 0000:00:1c.3: PCI bridge to [bus 44-44] > >> [ 1.243621] pci 0000:00:1c.3: bridge window [mem 0xd0500000- > 0xd05fffff] > >> [ 1.243699] pci 0000:00:1e.0: PCI bridge to [bus 45-45] > >> [ 1.243769] pci 0000:00:1e.0: bridge window [mem 0xd0400000- > 0xd04fffff] > >> [ 1.243861] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 > >> [ 1.243934] pci 0000:00:1c.0: setting latency timer to 64 > >> [ 1.243945] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16 > >> [ 1.244018] pci 0000:00:1c.1: setting latency timer to 64 > >> [ 1.244028] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 > >> [ 1.244101] pci 0000:00:1c.2: setting latency timer to 64 > >> [ 1.244111] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19 > >> [ 1.244184] pci 0000:00:1c.3: setting latency timer to 64 > >> [ 1.244191] pci 0000:00:1e.0: setting latency timer to 64 > >> [ 1.244196] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] > >> [ 1.244198] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] > >> [ 1.244199] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] > >> [ 1.244201] pci_bus 0000:00: resource 7 [mem 0xc0000000-0xdfffffff] > >> [ 1.244203] pci_bus 0000:00: resource 8 [mem 0xf0000000-0xfedfffff] > >> [ 1.244204] pci_bus 0000:00: resource 9 [mem 0xfee01000-0xffffffff] > >> [ 1.244206] pci_bus 0000:01: resource 1 [mem 0xd4700000-0xd47fffff] > >> [ 1.244208] pci_bus 0000:02: resource 0 [io 0x2000-0x3fff] > >> [ 1.244210] pci_bus 0000:02: resource 1 [mem 0xd0700000-0xd46fffff] > >> [ 1.244212] pci_bus 0000:02: resource 2 [mem 0xd4a00000-0xd4bfffff > >> 64bit pref] > >> [ 1.244214] pci_bus 0000:43: resource 1 [mem 0xd0600000-0xd06fffff] > >> [ 1.244216] pci_bus 0000:44: resource 1 [mem 0xd0500000-0xd05fffff] > >> [ 1.244218] pci_bus 0000:45: resource 1 [mem 0xd0400000-0xd04fffff] > >> [ 1.244220] pci_bus 0000:45: resource 4 [io 0x0000-0x0cf7] > >> [ 1.244222] pci_bus 0000:45: resource 5 [io 0x0d00-0xffff] > >> [ 1.244223] pci_bus 0000:45: resource 6 [mem 0x000a0000-0x000bffff] > >> [ 1.244225] pci_bus 0000:45: resource 7 [mem 0xc0000000-0xdfffffff] > >> [ 1.244227] pci_bus 0000:45: resource 8 [mem 0xf0000000-0xfedfffff] > >> [ 1.244229] pci_bus 0000:45: resource 9 [mem 0xfee01000-0xffffffff] > >> [ 1.244263] NET: Registered protocol family 2 > >> [ 1.244441] IP route cache hash table entries: 131072 (order: 8, > >> 1048576 bytes) > >> [ 1.245240] TCP established hash table entries: 524288 (order: 11, > >> 8388608 bytes) > >> [ 1.246949] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) > >> [ 1.247249] TCP: Hash tables configured (established 524288 bind 65536) > >> [ 1.247319] TCP reno registered > >> [ 1.247387] UDP hash table entries: 2048 (order: 4, 65536 bytes) > >> [ 1.247476] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) > >> [ 1.247641] NET: Registered protocol family 1 > >> [ 1.247721] pci 0000:00:02.0: Boot video device > >> [ 1.247741] pci 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 > >> [ 1.247845] pci 0000:00:1a.0: PCI INT A disabled > >> [ 1.247938] pci 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 > >> [ 1.248036] pci 0000:00:1d.0: PCI INT A disabled > >> [ 1.248137] PCI: CLS 64 bytes, default 64 > >> [ 1.248139] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) > >> [ 1.248208] Placing 64MB software IO TLB between ffff8800b6fc9000 - > >> ffff8800bafc9000 > >> [ 1.248304] software IO TLB at phys 0xb6fc9000 - 0xbafc9000 > >> [ 1.248841] audit: initializing netlink socket (disabled) > >> [ 1.248920] type=2000 audit(1348478288.088:1): initialized > >> [ 1.269455] HugeTLB registered 2 MB page size, pre-allocated 0 pages > >> [ 1.271294] VFS: Disk quotas dquot_6.5.2 > >> [ 1.271401] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) > >> [ 1.271887] fuse init (API version 7.17) > >> [ 1.272024] msgmni has been set to 7489 > >> [ 1.272476] Block layer SCSI generic (bsg) driver version 0.4 > >> loaded (major 253) > >> [ 1.272601] io scheduler noop registered > >> [ 1.272664] io scheduler deadline registered > >> [ 1.272752] io scheduler cfq registered (default) > >> [ 1.272911] pcieport 0000:00:1c.0: setting latency timer to 64 > >> [ 1.272969] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X > >> [ 1.273051] pcieport 0000:00:1c.1: setting latency timer to 64 > >> [ 1.273101] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X > >> [ 1.273188] pcieport 0000:00:1c.2: setting latency timer to 64 > >> [ 1.273237] pcieport 0000:00:1c.2: irq 42 for MSI/MSI-X > >> [ 1.273314] pcieport 0000:00:1c.3: setting latency timer to 64 > >> [ 1.273363] pcieport 0000:00:1c.3: irq 43 for MSI/MSI-X > >> [ 1.273459] pcieport 0000:00:1c.0: Signaling PME through PCIe PME > interrupt > >> [ 1.273533] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme > loaded > >> [ 1.273552] pcieport 0000:00:1c.1: Signaling PME through PCIe PME > interrupt > >> [ 1.273625] pcie_pme 0000:00:1c.1:pcie01: service driver pcie_pme > loaded > >> [ 1.273642] pcieport 0000:00:1c.2: Signaling PME through PCIe PME > interrupt > >> [ 1.273714] pci 0000:43:00.0: Signaling PME through PCIe PME interrupt > >> [ 1.273783] pci 0000:43:00.1: Signaling PME through PCIe PME interrupt > >> [ 1.273852] pci 0000:43:00.2: Signaling PME through PCIe PME interrupt > >> [ 1.274506] pci 0000:43:00.3: Signaling PME through PCIe PME interrupt > >> [ 1.274578] pcie_pme 0000:00:1c.2:pcie01: service driver pcie_pme > loaded > >> [ 1.274596] pcieport 0000:00:1c.3: Signaling PME through PCIe PME > interrupt > >> [ 1.274666] pci 0000:44:00.0: Signaling PME through PCIe PME interrupt > >> [ 1.274737] pcie_pme 0000:00:1c.3:pcie01: service driver pcie_pme > loaded > >> [ 1.274749] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > >> [ 1.274872] pciehp 0000:00:1c.1:pcie04: HPC vendor_id 8086 > >> device_id 3b44 ss_vid 103c ss_did 146d > >> [ 1.274994] pciehp 0000:00:1c.1:pcie04: service driver pciehp loaded > >> [ 1.275000] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 > >> [ 1.275131] intel_idle: MWAIT substates: 0x1120 > >> [ 1.275133] intel_idle: v0.4 model 0x25 > >> [ 1.275134] intel_idle: lapic_timer_reliable_states 0xffffffff > >> [ 1.275279] ACPI: Deprecated procfs I/F for AC is loaded, please > >> retry with CONFIG_ACPI_PROCFS_POWER cleared > >> [ 1.275464] ACPI: AC Adapter [AC] (on-line) > >> [ 1.275712] input: Sleep Button as > >> /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input0 > >> [ 1.275815] ACPI: Sleep Button [SLPB] > >> [ 1.275907] input: Lid Switch as > >> /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1 > >> [ 1.276025] ACPI: Lid Switch [LID] > >> [ 1.276113] input: Power Button as > >> /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2 > >> [ 1.276210] ACPI: Power Button [PWRF] > >> [ 1.283935] thermal LNXTHERM:00: registered as thermal_zone0 > >> [ 1.284002] ACPI: Thermal Zone [EXTZ] (23 C) > >> [ 1.284098] thermal LNXTHERM:01: registered as thermal_zone1 > >> [ 1.284165] ACPI: Thermal Zone [EX2Z] (0 C) > >> [ 1.284268] thermal LNXTHERM:02: registered as thermal_zone2 > >> [ 1.284334] ACPI: Thermal Zone [PWMZ] (0 C) > >> [ 1.286920] thermal LNXTHERM:03: registered as thermal_zone3 > >> [ 1.286987] ACPI: Thermal Zone [LOCZ] (24 C) > >> [ 1.287435] thermal LNXTHERM:04: registered as thermal_zone4 > >> [ 1.287502] ACPI: Thermal Zone [GFXZ] (0 C) > >> [ 1.298707] thermal LNXTHERM:05: registered as thermal_zone5 > >> [ 1.298774] ACPI: Thermal Zone [BATZ] (20 C) > >> [ 1.308382] thermal LNXTHERM:06: registered as thermal_zone6 > >> [ 1.308449] ACPI: Thermal Zone [EGXZ] (0 C) > >> [ 1.308757] thermal LNXTHERM:07: registered as thermal_zone7 > >> [ 1.308823] ACPI: Thermal Zone [CPUZ] (127 C) > >> [ 1.309028] thermal LNXTHERM:08: registered as thermal_zone8 > >> [ 1.309096] ACPI: Thermal Zone [MCHZ] (0 C) > >> [ 1.309296] thermal LNXTHERM:09: registered as thermal_zone9 > >> [ 1.309363] ACPI: Thermal Zone [PCHZ] (59 C) > >> [ 1.309445] ACPI: Deprecated procfs I/F for battery is loaded, > >> please retry with CONFIG_ACPI_PROCFS_POWER cleared > >> [ 1.309554] ACPI: Battery Slot [BAT0] (battery absent) > >> [ 1.309629] ACPI: Deprecated procfs I/F for battery is loaded, > >> please retry with CONFIG_ACPI_PROCFS_POWER cleared > >> [ 1.309642] ACPI: Battery Slot [BAT0] (battery absent) > >> [ 1.309799] ACPI: Battery Slot [BAT1] (battery absent) > >> [ 1.309864] ACPI: Battery Slot [BAT1] (battery absent) > >> [ 1.309952] ERST: Table is not found! > >> [ 1.310013] GHES: HEST is not enabled! > >> [ 1.310140] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled > >> [ 1.503094] Linux agpgart interface v0.103 > >> [ 1.503224] agpgart-intel 0000:00:00.0: Intel HD Graphics Chipset > >> [ 1.503380] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K > >> total, 262144K mappable > >> [ 1.504241] agpgart-intel 0000:00:00.0: detected 32768K stolen memory > >> [ 1.504466] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ > 0xc0000000 > >> [ 1.505825] brd: module loaded > >> [ 1.506532] loop: module loaded > >> [ 1.506736] ahci 0000:00:1f.2: version 3.0 > >> [ 1.506759] ahci 0000:00:1f.2: PCI INT A -> GSI 21 (level, low) -> IRQ 21 > >> [ 1.506880] ahci 0000:00:1f.2: irq 44 for MSI/MSI-X > >> [ 1.506917] ahci: SSS flag set, parallel bus scan disabled > >> [ 1.522717] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 3 > >> Gbps 0x37 impl SATA mode > >> [ 1.522822] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led > >> clo pio slum part ems sxs apst > >> [ 1.522925] ahci 0000:00:1f.2: setting latency timer to 64 > >> [ 1.555071] scsi0 : ahci > >> [ 1.555225] scsi1 : ahci > >> [ 1.555349] scsi2 : ahci > >> [ 1.555474] scsi3 : ahci > >> [ 1.555600] scsi4 : ahci > >> [ 1.555722] scsi5 : ahci > >> [ 1.555973] ata1: SATA max UDMA/133 abar m2048@0xd4827000 port > >> 0xd4827100 irq 44 > >> [ 1.556070] ata2: SATA max UDMA/133 abar m2048@0xd4827000 port > >> 0xd4827180 irq 44 > >> [ 1.556167] ata3: SATA max UDMA/133 abar m2048@0xd4827000 port > >> 0xd4827200 irq 44 > >> [ 1.556264] ata4: DUMMY > >> [ 1.556321] ata5: SATA max UDMA/133 abar m2048@0xd4827000 port > >> 0xd4827300 irq 44 > >> [ 1.556418] ata6: SATA max UDMA/133 abar m2048@0xd4827000 port > >> 0xd4827380 irq 44 > >> [ 1.556811] Fixed MDIO Bus: probed > >> [ 1.556886] tun: Universal TUN/TAP device driver, 1.6 > >> [ 1.556950] tun: (C) 1999-2004 Max Krasnyansky > <maxk@xxxxxxxxxxxx> > >> [ 1.557086] PPP generic driver version 2.4.2 > >> [ 1.557262] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver > >> [ 1.557346] ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ > 16 > >> [ 1.557436] ehci_hcd 0000:00:1a.0: setting latency timer to 64 > >> [ 1.557440] ehci_hcd 0000:00:1a.0: EHCI Host Controller > >> [ 1.557555] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned > >> bus number 1 > >> [ 1.557679] ehci_hcd 0000:00:1a.0: debug port 2 > >> [ 1.561630] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported > >> [ 1.561645] ehci_hcd 0000:00:1a.0: irq 16, io mem 0xd4829000 > >> [ 1.574587] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00 > >> [ 1.574784] hub 1-0:1.0: USB hub found > >> [ 1.574848] hub 1-0:1.0: 2 ports detected > >> [ 1.574966] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ > 20 > >> [ 1.575049] ehci_hcd 0000:00:1d.0: setting latency timer to 64 > >> [ 1.575052] ehci_hcd 0000:00:1d.0: EHCI Host Controller > >> [ 1.575163] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned > >> bus number 2 > >> [ 1.575282] ehci_hcd 0000:00:1d.0: debug port 2 > >> [ 1.579242] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported > >> [ 1.579257] ehci_hcd 0000:00:1d.0: irq 20, io mem 0xd4828000 > >> [ 1.594551] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00 > >> [ 1.594740] hub 2-0:1.0: USB hub found > >> [ 1.594803] hub 2-0:1.0: 2 ports detected > >> [ 1.594913] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver > >> [ 1.594989] uhci_hcd: USB Universal Host Controller Interface driver > >> [ 1.595094] usbcore: registered new interface driver libusual > >> [ 1.595192] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] > >> at 0x60,0x64 irq 1,12 > >> [ 1.597010] i8042: Detected active multiplexing controller, rev 1.1 > >> [ 1.597848] serio: i8042 KBD port at 0x60,0x64 irq 1 > >> [ 1.597916] serio: i8042 AUX0 port at 0x60,0x64 irq 12 > >> [ 1.597985] serio: i8042 AUX1 port at 0x60,0x64 irq 12 > >> [ 1.598090] serio: i8042 AUX2 port at 0x60,0x64 irq 12 > >> [ 1.598171] serio: i8042 AUX3 port at 0x60,0x64 irq 12 > >> [ 1.598322] mousedev: PS/2 mouse device common for all mice > >> [ 1.598559] rtc_cmos 00:08: RTC can wake from S4 > >> [ 1.598728] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0 > >> [ 1.598826] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs > >> [ 1.598958] device-mapper: uevent: version 1.0.3 > >> [ 1.599084] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) > >> initialised: dm-devel@xxxxxxxxxx > >> [ 1.599266] cpuidle: using governor ladder > >> [ 1.599446] cpuidle: using governor menu > >> [ 1.599506] EFI Variables Facility v0.08 2004-May-17 > >> [ 1.599764] TCP cubic registered > >> [ 1.599902] NET: Registered protocol family 10 > >> [ 1.600360] NET: Registered protocol family 17 > >> [ 1.600426] Registering the dns_resolver key type > >> [ 1.600615] PM: Hibernation image not present or could not be loaded. > >> [ 1.600628] registered taskstats version 1 > >> [ 1.610898] Magic number: 12:47:324 > >> [ 1.611016] tty tty49: hash matches > >> [ 1.611110] acpi PNP0B00:00: hash matches > >> [ 1.611269] rtc_cmos 00:08: setting system clock to 2012-09-24 > >> 09:18:09 UTC (1348478289) > >> [ 1.612256] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found > >> [ 1.612323] EDD information not available. > >> [ 1.621072] input: AT Translated Set 2 keyboard as > >> /devices/platform/i8042/serio0/input/input3 > >> [ 1.874156] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) > >> [ 1.874974] ata1.00: unexpected _GTF length (8) > >> [ 1.875315] ata1.00: ATA-8: Hitachi HTS725032A9A364, PC3OC72E, max > >> UDMA/100 > >> [ 1.875389] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth > 31/32), > >> AA > >> [ 1.876412] ata1.00: unexpected _GTF length (8) > >> [ 1.876746] ata1.00: configured for UDMA/100 > >> [ 1.877162] scsi 0:0:0:0: Direct-Access ATA Hitachi > >> HTS72503 PC3O PQ: 0 ANSI: 5 > >> [ 1.877480] sd 0:0:0:0: Attached scsi generic sg0 type 0 > >> [ 1.877527] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: > >> (320 GB/298 GiB) > >> [ 1.877680] sd 0:0:0:0: [sda] Write Protect is off > >> [ 1.877770] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > >> [ 1.877844] sd 0:0:0:0: [sda] Write cache: enabled, read cache: > >> enabled, doesn't support DPO or FUA > >> [ 1.886134] usb 1-1: new high-speed USB device number 2 using > ehci_hcd > >> [ 1.940007] sda: sda1 sda2 sda3 < sda5 sda6 > > >> [ 1.941565] sd 0:0:0:0: [sda] Attached SCSI disk > >> [ 2.018847] hub 1-1:1.0: USB hub found > >> [ 2.019040] hub 1-1:1.0: 6 ports detected > >> [ 2.129745] usb 2-1: new high-speed USB device number 2 using > ehci_hcd > >> [ 2.193604] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) > >> [ 2.213233] ata2.00: unexpected _GTF length (8) > >> [ 2.213304] ata2.00: ATAPI: hp CDDVDW TS-L633N, 0300, max > UDMA/100 > >> [ 2.234760] ata2.00: unexpected _GTF length (8) > >> [ 2.234831] ata2.00: configured for UDMA/100 > >> [ 2.240009] scsi 1:0:0:0: CD-ROM hp CDDVDW > >> TS-L633N 0300 PQ: 0 ANSI: 5 > >> [ 2.245488] Refined TSC clocksource calibration: 2393.996 MHz. > >> [ 2.245562] Switching to clocksource tsc > >> [ 2.248583] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw > >> xa/form2 cdda tray > >> [ 2.248674] cdrom: Uniform CD-ROM driver Revision: 3.20 > >> [ 2.248977] sr 1:0:0:0: Attached scsi CD-ROM sr0 > >> [ 2.249182] sr 1:0:0:0: Attached scsi generic sg1 type 5 > >> [ 2.262328] hub 2-1:1.0: USB hub found > >> [ 2.262465] hub 2-1:1.0: 8 ports detected > >> [ 2.333496] usb 1-1.3: new full-speed USB device number 3 using > ehci_hcd > >> [ 2.497215] usb 1-1.5: new high-speed USB device number 4 using > ehci_hcd > >> [ 2.568948] ata3: SATA link down (SStatus 0 SControl 300) > >> [ 2.888390] ata5: SATA link down (SStatus 0 SControl 300) > >> [ 3.207839] ata6: SATA link down (SStatus 0 SControl 300) > >> [ 3.209564] Freeing unused kernel memory: 920k freed > >> [ 3.210355] Write protecting the kernel read-only data: 12288k > >> [ 3.215443] Freeing unused kernel memory: 1616k freed > >> [ 3.219422] Freeing unused kernel memory: 1200k freed > >> [ 3.239703] udevd[109]: starting version 175 > >> [ 3.266328] [drm] Initialized drm 1.1.0 20060810 > >> [ 3.266529] e1000e: Intel(R) PRO/1000 Network Driver - 1.5.1-k > >> [ 3.266591] e1000e: Copyright(c) 1999 - 2011 Intel Corporation. > >> [ 3.266691] e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 > >> [ 3.266771] e1000e 0000:00:19.0: setting latency timer to 64 > >> [ 3.266910] e1000e 0000:00:19.0: irq 45 for MSI/MSI-X > >> [ 3.272545] firewire_ohci 0000:43:00.3: PCI INT D -> GSI 17 (level, > >> low) -> IRQ 17 > >> [ 3.272641] firewire_ohci 0000:43:00.3: setting latency timer to 64 > >> [ 3.274152] sdhci: Secure Digital Host Controller Interface driver > >> [ 3.274219] sdhci: Copyright(c) Pierre Ossman > >> [ 3.277077] wmi: Mapper loaded > >> [ 3.335711] firewire_ohci: Added fw-ohci device 0000:43:00.3, OHCI > >> v1.10, 4 IR + 4 IT contexts, quirks 0x11 > >> [ 3.335942] sdhci-pci 0000:43:00.0: SDHCI controller found > >> [1180:e822] (rev 1) > >> [ 3.336053] sdhci-pci 0000:43:00.0: PCI INT A -> GSI 18 (level, > >> low) -> IRQ 18 > >> [ 3.336220] sdhci-pci 0000:43:00.0: Will use DMA mode even though > >> HW doesn't fully claim to support it. > >> [ 3.336329] sdhci-pci 0000:43:00.0: setting latency timer to 64 > >> [ 3.336349] mmc0: no vmmc regulator found > >> [ 3.336442] Registered led device: mmc0:: > >> [ 3.337484] mmc0: SDHCI controller on PCI [0000:43:00.0] using DMA > >> [ 3.483459] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width > >> x1) 1c:c1:de:b2:a6:2e > >> [ 3.483565] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network > >> Connection > >> [ 3.483681] e1000e 0000:00:19.0: eth0: MAC: 9, PHY: 10, PBA No: FFFFFF- > 0FF > >> [ 3.483849] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 > >> [ 3.483923] i915 0000:00:02.0: setting latency timer to 64 > >> [ 3.527006] i915 0000:00:02.0: irq 46 for MSI/MSI-X > >> [ 3.527011] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). > >> [ 3.527084] [drm] Driver supports precise vblank timestamp query. > >> [ 3.527189] vgaarb: device changed decodes: > >> PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem > >> [ 3.834963] firewire_core: created device fw0: GUID 5566778811223344, > >> S400 > >> [ 4.059486] fbcon: inteldrmfb (fb0) is primary device > >> [ 4.325380] Console: switching to colour frame buffer device 200x56 > >> [ 4.328798] fb0: inteldrmfb frame buffer device > >> [ 4.328800] drm: registered panic notifier > >> [ 4.333758] acpi device:0e: registered as cooling_device4 > >> [ 4.334005] input: Video Bus as > >> > /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:01/input/input4 > >> [ 4.334122] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: > no) > >> [ 4.334223] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor > 0 > >> [ 4.766990] EXT4-fs (sda5): mounted filesystem with ordered data > >> mode. Opts: (null) > >> [ 24.352058] ADDRCONF(NETDEV_UP): eth0: link is not ready > >> [ 24.372676] udevd[409]: starting version 175 > >> [ 24.384405] lp: driver loaded but no devices found > >> [ 24.432637] Adding 4881404k swap on /dev/sda6. Priority:-1 > >> extents:1 across:4881404k > >> [ 24.456744] tpm_tis 00:04: 1.2 TPM (device-id 0xB, rev-id 16) > >> [ 24.470523] hp_accel: hardware type HPB64xx found > >> [ 24.471766] mei: module is from the staging directory, the quality > >> is unknown, you have been warned. > >> [ 24.472194] mei 0000:00:16.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 > >> [ 24.472202] mei 0000:00:16.0: setting latency timer to 64 > >> [ 24.472280] mei 0000:00:16.0: irq 47 for MSI/MSI-X > >> [ 24.472337] lis3lv02d: 8 bits sensor found > >> [ 24.477930] Blacklisted intel_ips for HP ProBook > >> [ 24.484742] lib80211: common routines for IEEE802.11 drivers > >> [ 24.484745] lib80211_crypt: registered algorithm 'NULL' > >> [ 24.493959] wl: module license 'MIXED/Proprietary' taints kernel. > >> [ 24.493963] Disabling lock debugging due to kernel taint > >> [ 24.504026] wl 0000:44:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 > >> [ 24.504038] wl 0000:44:00.0: setting latency timer to 64 > >> [ 24.527069] input: ST LIS3LV02DL Accelerometer as > >> /devices/platform/lis3lv02d/input/input5 > >> [ 24.527233] Registered led device: hp::hddprotect > >> [ 24.527263] hp_accel: driver loaded > >> [ 24.531646] udevd[425]: renamed network interface eth0 to eth3 > >> [ 24.541272] Linux video capture interface: v2.00 > >> [ 24.541711] uvcvideo: Found UVC 1.00 device Villem (0461:4db6) > >> [ 24.542995] lib80211_crypt: registered algorithm 'TKIP' > >> [ 24.543303] eth0: Broadcom BCM4727 802.11 Hybrid Wireless > >> Controller 5.100.82.38 > >> [ 24.551061] input: Villem as > >> /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.5/1-1.5:1.0/input/input6 > >> [ 24.551230] usbcore: registered new interface driver uvcvideo > >> [ 24.551233] USB Video Class driver (1.1.1) > >> [ 24.620129] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to > D0 > >> [ 24.620140] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to > D0 > >> [ 24.620153] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, > >> low) -> IRQ 16 > >> [ 24.620259] snd_hda_intel 0000:00:1b.0: irq 48 for MSI/MSI-X > >> [ 24.620299] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 > >> [ 24.644948] type=1400 audit(1348474712.569:2): apparmor="STATUS" > >> operation="profile_load" name="/sbin/dhclient" pid=676 > >> comm="apparmor_parser" > >> [ 24.644957] type=1400 audit(1348474712.569:3): apparmor="STATUS" > >> operation="profile_replace" name="/sbin/dhclient" pid=593 > >> comm="apparmor_parser" > >> [ 24.645422] type=1400 audit(1348474712.569:4): apparmor="STATUS" > >> operation="profile_load" > >> name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=676 > >> comm="apparmor_parser" > >> [ 24.645432] type=1400 audit(1348474712.569:5): apparmor="STATUS" > >> operation="profile_replace" > >> name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=593 > >> comm="apparmor_parser" > >> [ 24.645704] type=1400 audit(1348474712.569:6): apparmor="STATUS" > >> operation="profile_load" > >> name="/usr/lib/connman/scripts/dhclient-script" pid=676 > >> comm="apparmor_parser" > >> [ 24.645715] type=1400 audit(1348474712.569:7): apparmor="STATUS" > >> operation="profile_replace" > >> name="/usr/lib/connman/scripts/dhclient-script" pid=593 > >> comm="apparmor_parser" > >> [ 24.648408] type=1400 audit(1348474712.573:8): apparmor="STATUS" > >> operation="profile_load" name="/usr/sbin/ntpd" pid=800 > >> comm="apparmor_parser" > >> [ 24.649172] type=1400 audit(1348474712.573:9): apparmor="STATUS" > >> operation="profile_replace" name="/usr/sbin/ntpd" pid=802 > >> comm="apparmor_parser" > >> [ 24.679398] udevd[422]: renamed network interface eth0 to eth1 > >> [ 24.687350] HDMI status: Codec=3 Pin=4 Presence_Detect=0 > ELD_Valid=0 > >> [ 24.687414] HDMI status: Codec=3 Pin=5 Presence_Detect=0 > ELD_Valid=0 > >> [ 24.687471] HDMI status: Codec=3 Pin=6 Presence_Detect=0 > ELD_Valid=0 > >> [ 24.687569] input: HDA Intel HDMI/DP,pcm=8 as > >> /devices/pci0000:00/0000:00:1b.0/sound/card0/input7 > >> [ 24.688100] input: HDA Intel HDMI/DP,pcm=7 as > >> /devices/pci0000:00/0000:00:1b.0/sound/card0/input8 > >> [ 24.689681] input: HDA Intel HDMI/DP,pcm=3 as > >> /devices/pci0000:00/0000:00:1b.0/sound/card0/input9 > >> [ 24.690034] input: HDA Intel Line as > >> /devices/pci0000:00/0000:00:1b.0/sound/card0/input10 > >> [ 24.690184] input: HDA Intel Mic as > >> /devices/pci0000:00/0000:00:1b.0/sound/card0/input11 > >> [ 24.690333] input: HDA Intel Dock Headphone as > >> /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 > >> [ 24.690485] input: HDA Intel Headphone as > >> /devices/pci0000:00/0000:00:1b.0/sound/card0/input13 > >> [ 24.758861] EXT4-fs (sda5): re-mounted. Opts: errors=remount- > >> ro,user_xattr > >> [ 24.826745] input: HP WMI hotkeys as /devices/virtual/input/input14 > >> [ 25.142935] init: failsafe main process (957) killed by TERM signal > >> [ 25.303817] psmouse serio4: synaptics: Touchpad model: 1, fw: 7.2, > >> id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000 > >> [ 25.304623] Bluetooth: Core ver 2.16 > >> [ 25.304650] NET: Registered protocol family 31 > >> [ 25.304652] Bluetooth: HCI device and connection manager initialized > >> [ 25.304655] Bluetooth: HCI socket layer initialized > >> [ 25.304657] Bluetooth: L2CAP socket layer initialized > >> [ 25.304663] Bluetooth: SCO socket layer initialized > >> [ 25.307802] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 > >> [ 25.307806] Bluetooth: BNEP filters: protocol multicast > >> [ 25.313731] Bluetooth: RFCOMM TTY layer initialized > >> [ 25.313737] Bluetooth: RFCOMM socket layer initialized > >> [ 25.313739] Bluetooth: RFCOMM ver 1.11 > >> [ 25.341266] type=1400 audit(1348474713.265:10): apparmor="STATUS" > >> operation="profile_replace" name="/sbin/dhclient" pid=1056 > >> comm="apparmor_parser" > >> [ 25.341719] type=1400 audit(1348474713.269:11): apparmor="STATUS" > >> operation="profile_replace" > >> name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1056 > >> comm="apparmor_parser" > >> [ 25.349915] input: SynPS/2 Synaptics TouchPad as > >> /devices/platform/i8042/serio4/input/input15 > >> [ 25.383995] ppdev: user-space parallel port driver > >> [ 25.481592] e1000e 0000:00:19.0: irq 45 for MSI/MSI-X > >> [ 25.537333] e1000e 0000:00:19.0: irq 45 for MSI/MSI-X > >> [ 25.537896] ADDRCONF(NETDEV_UP): eth3: link is not ready > >> [ 25.538313] ADDRCONF(NETDEV_UP): eth3: link is not ready > >> [ 25.540084] ADDRCONF(NETDEV_UP): eth1: link is not ready > >> [ 25.607191] init: gdm main process (1159) killed by TERM signal > >> [ 28.726332] e1000e: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow > >> Control: Rx > >> [ 28.726737] ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready > >> [ 39.465232] eth3: no IPv6 routers present > >> -- > >> To unsubscribe from this list: send the line "unsubscribe linux-acpi" in > >> the body of a message to majordomo@xxxxxxxxxxxxxxx > >> More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-acpi" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
