Barbara, Sorry I overlooked: qunzip scanmodem.gz Which you need to change "q" to "g" as: $ gunzip scanModem.gz then run $ chmod +x scanModem $ .sudo ./scanModem send us ModemData.txt. This should work. A typo. Don't worry! Let us know if this was what was happening. Regards, Antonio On 7/8/10, Antonio Olivares <olivares14031@xxxxxxxxx> wrote: > Barbara, > > As far as I can see, you have an LT Modem which is well supported. > Now, depending on your system which kernel you have and if and you > have compiler installed and kernel sources/headers, you can get the > drivers. But remember that without the above tools you cannot do much > :( > > product: LT WinModem > vendor: Agere Systems > > Here you can find the drivers: > > http://linmodems.technion.ac.il/packages/ltmodem/kernel-2.6/martian/ > > But it still would be best that you can have all the utilities that > are needed, this would depend on your installation. Get scanModem, > gunzip scanModem.gz, and run > $ sudo ./scanModem > and send us ModemData.txt to make sure that the driver we recommend > is the one that will work. > > Regards, > > Antonio > > On 7/8/10, Barbara Denny and Assoc. <dennyandassoc@xxxxxxxxxxx> wrote: >> From: someone <mrleviguy@xxxxxxxxx> >> To: Discuss@xxxxxxxxxxxxx >> Subject: Barb, USA, installation of dialup pci HELP >> Date: 07/08/2010 01:19:31 PM >> I am trying to build computers to give to the poor with free internet >> service. Need Dialup Modem >> >> I am such a Ubuntu Newby that I can't get the qunzip scanmodem.gz to >> work/install (installed Gzip but still can't use gunzip) I am really >> over my head but have been trying to learn to use the terminal for about >> 37 >> hours to get the dialup modem to work. I have installed / ran lots of >> tries (apts ?) should I reinstall Ubuntu (some how I now have Kubuntu?) >> I am quick to learn but most of what I read and reread on the internet >> made >> ASSumptions that I knew where to start or finish. >> I think I just found the Root from Applications > Programs > is this >> THE >> Root?? >> >> anyway >> >> from the physical PCI card it reads F-1156iv/A3 >> IF THIS IS NOT A GOOD ENOUGH pci card >> -let me know and I will install another then contact you again with the >> new >> cards ID >> >> I have sent you 3 different looks at my system. the bottom is lshw modem >> only >> >> If you still need the ScanModem please explain how I can get it unzipped >> I do thank you for being there!!!!! >> >> description: Computer >> width: 32 bits >> *-core >> description: Motherboard >> physical id: 0 >> *-memory >> description: System memory >> physical id: 0 >> size: 243MiB >> *-cpu >> product: Pentium III (Coppermine) >> vendor: Intel Corp. >> physical id: 1 >> bus info: cpu@0 >> version: 6.8.6 >> size: 1GHz >> width: 32 bits >> capabilities: fpu fpu_exception wp vme de pse tsc msr pae mce >> cx8 mtrr pge mca cmov pse36 mmx fxsr sse up >> *-cache:0 >> description: L1 cache >> physical id: 0 >> size: 32KiB >> *-cache:1 >> description: L2 cache >> physical id: 1 >> size: 256KiB >> *-pci >> description: Host bridge >> product: 82815 815 Chipset Host Bridge and Memory Controller >> Hub >> vendor: Intel Corporation >> physical id: 100 >> bus info: pci@0000:00:00.0 >> version: 02 >> width: 32 bits >> clock: 33MHz >> configuration: driver=agpgart-intel >> resources: irq:0 >> *-display UNCLAIMED >> description: VGA compatible controller >> product: 82815 Chipset Graphics Controller (CGC) >> vendor: Intel Corporation >> physical id: 2 >> bus info: pci@0000:00:02.0 >> version: 02 >> width: 32 bits >> clock: 66MHz >> capabilities: bus_master cap_list >> configuration: latency=0 >> resources: memory:f0000000-f3ffffff(prefetchable) >> memory:ec000000-ec07ffff >> *-pci >> description: PCI bridge >> product: 82801AA PCI Bridge >> vendor: Intel Corporation >> physical id: 1e >> bus info: pci@0000:00:1e.0 >> version: 02 >> width: 32 bits >> clock: 33MHz >> capabilities: pci bus_master >> resources: ioport:2000(size=4096) memory:ec100000-ec1fffff >> memory:10000000-100fffff(prefetchable) >> *-communication UNCLAIMED >> description: Communication controller >> product: LT WinModem >> vendor: Agere Systems >> physical id: 1 >> bus info: pci@0000:01:01.0 >> version: 00 >> width: 32 bits >> clock: 33MHz >> capabilities: bus_master cap_list >> configuration: latency=64 maxlatency=14 mingnt=252 >> resources: memory:ec100000-ec1000ff ioport:2480(size=8) >> ioport:2000(size=256) >> *-network >> description: Ethernet interface >> product: 3c905C-TX/TX-M [Tornado] >> vendor: 3Com Corporation >> physical id: 4 >> bus info: pci@0000:01:04.0 >> logical name: eth0 >> version: 78 >> serial: 00:04:75:39:96:45 >> width: 32 bits >> clock: 33MHz >> capabilities: bus_master cap_list rom ethernet physical >> configuration: broadcast=yes driver=3c59x >> ip=192.168.1.101 latency=80 maxlatency=10 mingnt=10 multicast=yes >> resources: irq:5 ioport:2400(size=128) >> memory:ec100400-ec10047f memory:10000000-1001ffff(prefetchable) >> *-isa >> description: ISA bridge >> product: 82801AA ISA Bridge (LPC) >> vendor: Intel Corporation >> physical id: 1f >> bus info: pci@0000:00:1f.0 >> version: 02 >> width: 32 bits >> clock: 33MHz >> capabilities: isa bus_master >> configuration: latency=0 >> *-ide >> description: IDE interface >> product: 82801AA IDE Controller >> vendor: Intel Corporation >> physical id: 1f.1 >> bus info: pci@0000:00:1f.1 >> version: 02 >> width: 32 bits >> clock: 33MHz >> capabilities: ide bus_master >> configuration: driver=ata_piix latency=0 >> resources: irq:0 ioport:1f0(size=8) ioport:3f6 >> ioport:170(size=8) ioport:376 ioport:1800(size=16) >> *-usb >> description: USB Controller >> product: 82801AA USB Controller >> vendor: Intel Corporation >> physical id: 1f.2 >> bus info: pci@0000:00:1f.2 >> version: 02 >> width: 32 bits >> clock: 33MHz >> capabilities: bus_master >> configuration: driver=uhci_hcd latency=0 >> resources: irq:11 ioport:1820(size=32) >> *-serial UNCLAIMED >> description: SMBus >> product: 82801AA SMBus Controller >> vendor: Intel Corporation >> physical id: 1f.3 >> bus info: pci@0000:00:1f.3 >> version: 02 >> width: 32 bits >> clock: 33MHz >> configuration: latency=0 >> resources: ioport:1810(size=16) >> *-multimedia >> description: Multimedia audio controller >> product: 82801AA AC'97 Audio Controller >> vendor: Intel Corporation >> physical id: 1f.5 >> bus info: pci@0000:00:1f.5 >> version: 02 >> width: 32 bits >> clock: 33MHz >> capabilities: bus_master >> configuration: driver=Intel ICH latency=0 >> resources: irq:9 ioport:1200(size=256) ioport:1300(size=64) >> >> AND >> >> >> someone@someone-desktop:~$ lspci -vv >> 00:00.0 Host bridge: Intel Corporation 82815 815 Chipset Host Bridge and >> Memory Controller Hub (rev 02) >> Subsystem: Intel Corporation 82815 815 Chipset Host Bridge and >> Memory >> Controller Hub >> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- >> ParErr- >> Stepping- SERR+ FastB2B- DisINTx- >> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- >> <TAbort- >> <MAbort+ >SERR- <PERR- INTx- >> Latency: 0 >> Capabilities: <access denied> >> Kernel driver in use: agpgart-intel >> Kernel modules: intel-agp >> >> 00:02.0 VGA compatible controller: Intel Corporation 82815 Chipset >> Graphics Controller (CGC) (rev 02) >> Subsystem: Hewlett-Packard Company Device 1245 >> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- >> ParErr- >> Stepping- SERR- FastB2B- DisINTx- >> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- >> <TAbort- <MAbort- >SERR- <PERR- INTx- >> Latency: 0 >> Interrupt: pin A routed to IRQ 10 >> Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M] >> Region 1: Memory at ec000000 (32-bit, non-prefetchable) >> [size=512K] >> Capabilities: <access denied> >> >> 00:1e.0 PCI bridge: Intel Corporation 82801AA PCI Bridge (rev 02) >> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- >> ParErr- >> Stepping- SERR- FastB2B- DisINTx- >> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- >> <TAbort- >> <MAbort- >SERR- <PERR- INTx- >> Latency: 0 >> Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 >> I/O behind bridge: 00002000-00002fff >> Memory behind bridge: ec100000-ec1fffff >> Prefetchable memory behind bridge: 10000000-100fffff >> Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- >> <TAbort- <MAbort- <SERR- <PERR- >> BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- >> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- >> Kernel modules: shpchp >> >> 00:1f.0 ISA bridge: Intel Corporation 82801AA ISA Bridge (LPC) (rev 02) >> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- >> ParErr- >> Stepping- SERR- FastB2B- DisINTx- >> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- >> <TAbort- <MAbort- >SERR- <PERR- INTx- >> Latency: 0 >> Kernel modules: iTCO_wdt, intel-rng >> >> 00:1f.1 IDE interface: Intel Corporation 82801AA IDE Controller (rev 02) >> (prog-if 80 [Master]) >> Subsystem: Intel Corporation 82801AA IDE Controller >> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- >> ParErr- >> Stepping- SERR- FastB2B- DisINTx- >> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- >> <TAbort- <MAbort- >SERR- <PERR- INTx- >> Latency: 0 >> Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) >> [disabled] [size=8] >> Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) >> [disabled] [size=1] >> Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) >> [disabled] [size=8] >> Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) >> [disabled] [size=1] >> Region 4: I/O ports at 1800 [size=16] >> Kernel driver in use: ata_piix >> >> 00:1f.2 USB Controller: Intel Corporation 82801AA USB Controller (rev >> 02) >> Subsystem: Intel Corporation 82801AA USB Controller >> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- >> ParErr- >> Stepping- SERR- FastB2B- DisINTx- >> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- >> <TAbort- <MAbort- >SERR- <PERR- INTx- >> Latency: 0 >> Interrupt: pin D routed to IRQ 11 >> Region 4: I/O ports at 1820 [size=32] >> Kernel driver in use: uhci_hcd >> >> 00:1f.3 SMBus: Intel Corporation 82801AA SMBus Controller (rev 02) >> Subsystem: Intel Corporation 82801AA SMBus Controller >> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- >> ParErr- >> Stepping- SERR- FastB2B- DisINTx- >> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- >> <TAbort- <MAbort- >SERR- <PERR- INTx- >> Interrupt: pin B routed to IRQ 9 >> Region 4: I/O ports at 1810 [size=16] >> Kernel modules: i2c-i801 >> >> 00:1f.5 Multimedia audio controller: Intel Corporation 82801AA AC'97 >> Audio Controller (rev 02) >> Subsystem: Hewlett-Packard Company Device 1249 >> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- >> ParErr- >> Stepping- SERR- FastB2B- DisINTx- >> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- >> <TAbort- <MAbort- >SERR- <PERR- INTx- >> Latency: 0 >> Interrupt: pin B routed to IRQ 9 >> Region 0: I/O ports at 1200 [size=256] >> Region 1: I/O ports at 1300 [size=64] >> Kernel driver in use: Intel ICH >> Kernel modules: snd-intel8x0 >> >> 01:01.0 Communication controller: Agere Systems LT WinModem >> Subsystem: GVC Corporation Device 0405 >> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- >> ParErr- >> Stepping- SERR- FastB2B- DisINTx- >> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- >> <TAbort- <MAbort- >SERR- <PERR- INTx- >> Latency: 64 (63000ns min, 3500ns max) >> Interrupt: pin A routed to IRQ 5 >> Region 0: Memory at ec100000 (32-bit, non-prefetchable) >> [size=256] >> Region 1: I/O ports at 2480 [size=8] >> Region 2: I/O ports at 2000 [size=256] >> Capabilities: <access denied> >> >> 01:04.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] >> (rev 78) >> Subsystem: Hewlett-Packard Company Device 1246 >> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- >> ParErr- >> Stepping- SERR- FastB2B- DisINTx- >> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- >> <TAbort- <MAbort- >SERR- <PERR- INTx- >> Latency: 80 (2500ns min, 2500ns max), Cache Line Size: 32 bytes >> Interrupt: pin A routed to IRQ 5 >> Region 0: I/O ports at 2400 [size=128] >> Region 1: Memory at ec100400 (32-bit, non-prefetchable) >> [size=128] >> [virtual] Expansion ROM at 10000000 [disabled] [size=128K] >> Capabilities: <access denied> >> Kernel driver in use: 3c59x >> Kernel modules: 3c59x >> >> >> >> someone@someone-desktop:~$ lspci -vv >> >> *-communication UNCLAIMED >> description: Communication controller >> product: LT WinModem >> vendor: Agere Systems >> physical id: 1 >> bus info: pci@0000:01:01.0 >> version: 00 >> width: 32 bits >> clock: 33MHz >> capabilities: bus_master cap_list >> configuration: latency=64 maxlatency=14 mingnt=252 >> resources: memory:ec100000-ec1000ff ioport:2480(size=8) >> ioport:2 >> >> >> >> >> >> >> >> >> >> ____________________________________________________________ >> Penny Stock Jumping 2000% >> Sign up to the #1 voted penny stock newsletter for free today! >> http://thirdpartyoffers.netzero.net/TGL3241/4c363758b99cb225363st02vuc >> >
