Re: barb, usa, installation of dialup pci HELP

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Barbara,

As far as I can see, you have an LT Modem which is well supported.
Now, depending on your system which kernel you have and if and you
have compiler installed and kernel sources/headers, you can get the
drivers.  But remember that without the above tools you cannot do much
:(

               product: LT WinModem
                vendor: Agere Systems

Here you can find the drivers:

http://linmodems.technion.ac.il/packages/ltmodem/kernel-2.6/martian/

But it still would be best that you can have all the utilities that
are needed, this would depend on your installation.  Get scanModem,
gunzip scanModem.gz, and run
$ sudo ./scanModem
 and send us ModemData.txt to make sure that the driver we recommend
is the one that will work.

Regards,

Antonio

On 7/8/10, Barbara Denny and Assoc. <dennyandassoc@xxxxxxxxxxx> wrote:
> From: 	someone <mrleviguy@xxxxxxxxx>
> To: 	Discuss@xxxxxxxxxxxxx
> Subject: 	Barb, USA, installation of dialup pci  HELP
> Date: 	07/08/2010 01:19:31 PM
> I am trying to build computers to give to the poor with free internet
> service.  Need Dialup Modem
>
> I am such a Ubuntu Newby that I can't get the qunzip scanmodem.gz to
> work/install (installed Gzip but still can't use gunzip)  I am really
> over my head but have been trying to learn to use the terminal for about 37
> hours to get the dialup modem to work.   I have installed / ran lots of
> tries (apts ?) should I reinstall Ubuntu (some how I now have Kubuntu?)
> I am quick to learn but most of what I read and reread on the internet made
> ASSumptions that I knew where to start or finish.
> I think I just found the Root   from Applications > Programs >  is this THE
> Root??
>
> anyway
>
> from the physical PCI card it reads F-1156iv/A3
> IF THIS IS NOT A GOOD ENOUGH pci card
>  -let me know and I will install another then contact you again with the new
> cards ID
>
> I have sent you 3 different looks at my system. the bottom is lshw modem
> only
>
> If you still need the ScanModem  please explain how I can get it unzipped
> I do thank you for being there!!!!!
>
>  description: Computer
>     width: 32 bits
>   *-core
>        description: Motherboard
>        physical id: 0
>      *-memory
>           description: System memory
>           physical id: 0
>           size: 243MiB
>      *-cpu
>           product: Pentium III (Coppermine)
>           vendor: Intel Corp.
>           physical id: 1
>           bus info: cpu@0
>           version: 6.8.6
>           size: 1GHz
>           width: 32 bits
>           capabilities: fpu fpu_exception wp vme de pse tsc msr pae mce
> cx8 mtrr pge mca cmov pse36 mmx fxsr sse up
>         *-cache:0
>              description: L1 cache
>              physical id: 0
>              size: 32KiB
>         *-cache:1
>              description: L2 cache
>              physical id: 1
>              size: 256KiB
>      *-pci
>           description: Host bridge
>           product: 82815 815 Chipset Host Bridge and Memory Controller
> Hub
>           vendor: Intel Corporation
>           physical id: 100
>           bus info: pci@0000:00:00.0
>           version: 02
>           width: 32 bits
>           clock: 33MHz
>           configuration: driver=agpgart-intel
>           resources: irq:0
>         *-display UNCLAIMED
>              description: VGA compatible controller
>              product: 82815 Chipset Graphics Controller (CGC)
>              vendor: Intel Corporation
>              physical id: 2
>              bus info: pci@0000:00:02.0
>              version: 02
>              width: 32 bits
>              clock: 66MHz
>              capabilities: bus_master cap_list
>              configuration: latency=0
>              resources: memory:f0000000-f3ffffff(prefetchable)
> memory:ec000000-ec07ffff
>         *-pci
>              description: PCI bridge
>              product: 82801AA PCI Bridge
>              vendor: Intel Corporation
>              physical id: 1e
>              bus info: pci@0000:00:1e.0
>              version: 02
>              width: 32 bits
>              clock: 33MHz
>              capabilities: pci bus_master
>              resources: ioport:2000(size=4096) memory:ec100000-ec1fffff
> memory:10000000-100fffff(prefetchable)
>            *-communication UNCLAIMED
>                 description: Communication controller
>                 product: LT WinModem
>                 vendor: Agere Systems
>                 physical id: 1
>                 bus info: pci@0000:01:01.0
>                 version: 00
>                 width: 32 bits
>                 clock: 33MHz
>                 capabilities: bus_master cap_list
>                 configuration: latency=64 maxlatency=14 mingnt=252
>                 resources: memory:ec100000-ec1000ff ioport:2480(size=8)
> ioport:2000(size=256)
>            *-network
>                 description: Ethernet interface
>                 product: 3c905C-TX/TX-M [Tornado]
>                 vendor: 3Com Corporation
>                 physical id: 4
>                 bus info: pci@0000:01:04.0
>                 logical name: eth0
>                 version: 78
>                 serial: 00:04:75:39:96:45
>                 width: 32 bits
>                 clock: 33MHz
>                 capabilities: bus_master cap_list rom ethernet physical
>                 configuration: broadcast=yes driver=3c59x
> ip=192.168.1.101 latency=80 maxlatency=10 mingnt=10 multicast=yes
>                 resources: irq:5 ioport:2400(size=128)
> memory:ec100400-ec10047f memory:10000000-1001ffff(prefetchable)
>         *-isa
>              description: ISA bridge
>              product: 82801AA ISA Bridge (LPC)
>              vendor: Intel Corporation
>              physical id: 1f
>              bus info: pci@0000:00:1f.0
>              version: 02
>              width: 32 bits
>              clock: 33MHz
>              capabilities: isa bus_master
>              configuration: latency=0
>         *-ide
>              description: IDE interface
>              product: 82801AA IDE Controller
>              vendor: Intel Corporation
>              physical id: 1f.1
>              bus info: pci@0000:00:1f.1
>              version: 02
>              width: 32 bits
>              clock: 33MHz
>              capabilities: ide bus_master
>              configuration: driver=ata_piix latency=0
>              resources: irq:0 ioport:1f0(size=8) ioport:3f6
> ioport:170(size=8) ioport:376 ioport:1800(size=16)
>         *-usb
>              description: USB Controller
>              product: 82801AA USB Controller
>              vendor: Intel Corporation
>              physical id: 1f.2
>              bus info: pci@0000:00:1f.2
>              version: 02
>              width: 32 bits
>              clock: 33MHz
>              capabilities: bus_master
>              configuration: driver=uhci_hcd latency=0
>              resources: irq:11 ioport:1820(size=32)
>         *-serial UNCLAIMED
>              description: SMBus
>              product: 82801AA SMBus Controller
>              vendor: Intel Corporation
>              physical id: 1f.3
>              bus info: pci@0000:00:1f.3
>              version: 02
>              width: 32 bits
>              clock: 33MHz
>              configuration: latency=0
>              resources: ioport:1810(size=16)
>         *-multimedia
>              description: Multimedia audio controller
>              product: 82801AA AC'97 Audio Controller
>              vendor: Intel Corporation
>              physical id: 1f.5
>              bus info: pci@0000:00:1f.5
>              version: 02
>              width: 32 bits
>              clock: 33MHz
>              capabilities: bus_master
>              configuration: driver=Intel ICH latency=0
>              resources: irq:9 ioport:1200(size=256) ioport:1300(size=64)
>
> AND
>
>
> someone@someone-desktop:~$  lspci -vv
> 00:00.0 Host bridge: Intel Corporation 82815 815 Chipset Host Bridge and
> Memory Controller Hub (rev 02)
>         Subsystem: Intel Corporation 82815 815 Chipset Host Bridge and
> Memory
> Controller Hub
>         Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B- DisINTx-
>         Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort+ >SERR- <PERR- INTx-
>         Latency: 0
>         Capabilities: <access denied>
>         Kernel driver in use: agpgart-intel
>         Kernel modules: intel-agp
>
> 00:02.0 VGA compatible controller: Intel Corporation 82815 Chipset
> Graphics Controller (CGC) (rev 02)
>         Subsystem: Hewlett-Packard Company Device 1245
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
>         Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>         Latency: 0
>         Interrupt: pin A routed to IRQ 10
>         Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M]
>         Region 1: Memory at ec000000 (32-bit, non-prefetchable) [size=512K]
>         Capabilities: <access denied>
>
> 00:1e.0 PCI bridge: Intel Corporation 82801AA PCI Bridge (rev 02)
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
>         Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort-
> <MAbort- >SERR- <PERR- INTx-
>         Latency: 0
>         Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
>         I/O behind bridge: 00002000-00002fff
>         Memory behind bridge: ec100000-ec1fffff
>         Prefetchable memory behind bridge: 10000000-100fffff
>         Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- <SERR- <PERR-
>         BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
>                 PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
>         Kernel modules: shpchp
>
> 00:1f.0 ISA bridge: Intel Corporation 82801AA ISA Bridge (LPC) (rev 02)
>         Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
>         Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>         Latency: 0
>         Kernel modules: iTCO_wdt, intel-rng
>
> 00:1f.1 IDE interface: Intel Corporation 82801AA IDE Controller (rev 02)
> (prog-if 80 [Master])
>         Subsystem: Intel Corporation 82801AA IDE Controller
>         Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
>         Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>         Latency: 0
>         Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
> [disabled] [size=8]
>         Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
> [disabled] [size=1]
>         Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
> [disabled] [size=8]
>         Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
> [disabled] [size=1]
>         Region 4: I/O ports at 1800 [size=16]
>         Kernel driver in use: ata_piix
>
> 00:1f.2 USB Controller: Intel Corporation 82801AA USB Controller (rev
> 02)
>         Subsystem: Intel Corporation 82801AA USB Controller
>         Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
>         Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>         Latency: 0
>         Interrupt: pin D routed to IRQ 11
>         Region 4: I/O ports at 1820 [size=32]
>         Kernel driver in use: uhci_hcd
>
> 00:1f.3 SMBus: Intel Corporation 82801AA SMBus Controller (rev 02)
>         Subsystem: Intel Corporation 82801AA SMBus Controller
>         Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
>         Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>         Interrupt: pin B routed to IRQ 9
>         Region 4: I/O ports at 1810 [size=16]
>         Kernel modules: i2c-i801
>
> 00:1f.5 Multimedia audio controller: Intel Corporation 82801AA AC'97
> Audio Controller (rev 02)
>         Subsystem: Hewlett-Packard Company Device 1249
>         Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
>         Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>         Latency: 0
>         Interrupt: pin B routed to IRQ 9
>         Region 0: I/O ports at 1200 [size=256]
>         Region 1: I/O ports at 1300 [size=64]
>         Kernel driver in use: Intel ICH
>         Kernel modules: snd-intel8x0
>
> 01:01.0 Communication controller: Agere Systems LT WinModem
>         Subsystem: GVC Corporation Device 0405
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
>         Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>         Latency: 64 (63000ns min, 3500ns max)
>         Interrupt: pin A routed to IRQ 5
>         Region 0: Memory at ec100000 (32-bit, non-prefetchable) [size=256]
>         Region 1: I/O ports at 2480 [size=8]
>         Region 2: I/O ports at 2000 [size=256]
>         Capabilities: <access denied>
>
> 01:04.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado]
> (rev 78)
>         Subsystem: Hewlett-Packard Company Device 1246
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
>         Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>         Latency: 80 (2500ns min, 2500ns max), Cache Line Size: 32 bytes
>         Interrupt: pin A routed to IRQ 5
>         Region 0: I/O ports at 2400 [size=128]
>         Region 1: Memory at ec100400 (32-bit, non-prefetchable) [size=128]
>         [virtual] Expansion ROM at 10000000 [disabled] [size=128K]
>         Capabilities: <access denied>
>         Kernel driver in use: 3c59x
>         Kernel modules: 3c59x
>
>
>
> someone@someone-desktop:~$  lspci -vv
>
> *-communication UNCLAIMED
>                 description: Communication controller
>                 product: LT WinModem
>                 vendor: Agere Systems
>                 physical id: 1
>                 bus info: pci@0000:01:01.0
>                 version: 00
>                 width: 32 bits
>                 clock: 33MHz
>                 capabilities: bus_master cap_list
>                 configuration: latency=64 maxlatency=14 mingnt=252
>                 resources: memory:ec100000-ec1000ff ioport:2480(size=8)
> ioport:2
>
>
>
>
>
>
>
>
>
> ____________________________________________________________
> Penny Stock Jumping 2000%
> Sign up to the #1 voted penny stock newsletter for free today!
> http://thirdpartyoffers.netzero.net/TGL3241/4c363758b99cb225363st02vuc
>


[Index of Archives]     [Linux Media Development]     [Asterisk]     [DCCP]     [Netdev]     [X.org]     [Xfree86]     [Fedora Women]     [Linux USB]

  Powered by Linux