Martin,
Don't worry about wvdailconf not finding modem port. I have an
11c1:0630 modem and it does not find it.
03:00.0 Communication controller: Agere Systems Device 0630 (rev 01)
Predictive diagnostics for card in bus 03:00.0:
Modem chipset detected on
NAME="Communication controller: Agere Systems Device 0630 "
CLASS=0780
PCIDEV=11c1:0630
SUBSYS=11c1:0630
IRQ=16
HDA2=00:05.0
IDENT=agrsm
For candidate modem in: 03:00.0
0780 Communication controller: Agere Systems Device 0630
Primary device ID: 11c1:0630
Support type needed or chipset: agrsm
Please do the following as root user
$ su -
passwd:
#
Create a wvdial.conf with the editor of your choice, this can be vi,
gedit/kedit/kwrite any of them, but do this as root user.
Copy it like the one I have here:
root@darkstar:~# cat /etc/wvdial.conf
[Dialer Defaults]
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Modem Type = Analog Modem
Phone = YOUR_ISP_PHONE_NO_GOES_HERE
ISDN = 0
Username = YOUR_USERNAME
Init1 = ATZ
Password = YOUR_PASSWORD
Modem = /dev/modem
Baud = 57600
Stupid Mode = 1
;Auto DNS = yes
You may use a ":" in front of Stupid Mode = 1 line as well if you don't need it.
Attempt to dialout by doing the following:
## To make a logfile wvdial.out
# wvdial 2>&1 | tee wvdial.out
Send us wvdial.out.
Regards,
Antonio
On 5/25/10, mwl <mossianin_lbcmi@xxxxxxxxxx> wrote:
> Here are the results of your commands:
>
> [root@localhost agrsm06pci-2.1.80~20100106]# ls -l /dev/ttyA*
> crw-rw---- 1 root dialout 62, 67 2010-05-25 18:56 /dev/ttyAGS3
> [root@localhost agrsm06pci-2.1.80~20100106]# ls -sf /dev/ttyAGS3 /dev/modem
> /dev/ttyAGS3 /dev/modem@
> [root@localhost agrsm06pci-2.1.80~20100106]# ls -l /dev/ttyAGS3
> crw-rw---- 1 root dialout 62, 67 2010-05-25 18:56 /dev/ttyAGS3
> [root@localhost agrsm06pci-2.1.80~20100106]# ls -l /dev/ttyAGS3 /dev/modem
> lrwxrwxrwx 1 root root 5 2010-05-25 13:44 /dev/modem -> ttyS0
> crw-rw---- 1 root dialout 62, 67 2010-05-25 18:56 /dev/ttyAGS3
> <<end of results>>
>
> I retried KPPP using both /dev/modem and ttyS0 and both still show the
> modem is busy message.
>
> Thanks.
>
>
> On 05/25/2010 06:26 PM, Marvin Stodolsky wrote:
>> After the drivers are loaded, there should be a report that
>> /dev/ttyAGS3 has been created.
>> Check with ls -l /dev/ttyA*
>> Then set up a symbolic link:
>> # ln -sf /dev/ttyAGS3 /dev/modem
>> Check with:
>> # ls -l /dev/ttyAGS3 /dev/modem
>>
>> Then you can test use with /dev/modem
>>
>> The step
>> # ln -sf /dev/ttyAGS3 /dev/modem
>> must be redone upon every bootup for now.
>>
>> MarvS
>>
>> On Tue, May 25, 2010 at 11:57 AM, mwl<mossianin_lbcmi@xxxxxxxxxx> wrote:
>>
>>> Here are the results of the commands you suggested.
>>>
>>> # modprobe agrmodem
>>> # modprobe agrserial
>>> # ./agrsm-test
>>>
>>> Found drivers for boot kernel 2.6.32.12-pclos1.bfs at:
>>> find: paths must precede expression: agrserial.ko
>>> Usage: find [-H] [-L] [-P] [-Olevel] [-D
>>> help|tree|search|stat|rates|opt|exec] [path...] [expression]
>>>
>>>
>>>
>>> Loading drivers:
>>>
>>> Checking for utility wvdialconf
>>> Utility wvdialconf not found
>>>
>>> The installation record has been written to ./agrsm-test.txt
>>> <<end>>
>>>
>>> I rebooted and rechecked with
>>> # modprobe -l agr*
>>> kernel/drivers/extra/agrserial.ko.gz
>>> kernel/drivers/extra/agrmodem.ko.gz
>>> extra/agrserial.ko
>>> extra/agrmodem.ko
>>>
>>> I know you prefer to test with wvdial, but because I am still having
>>> problems getting wvdial and wvstreams installed, I tried dialing out with
>>> KPPP and get the same message about the modem being busy. I am trying to
>>> connect with the dev/modem device. I looked thru the list of available
>>> modems trying to find one that used AGR or something similar, but there
>>> was
>>> none.
>>>
>>> Thanks for your continued help.
>>>
>>>
>>>
>>> On 05/24/2010 06:52 PM, Marvin Stodolsky wrote:
>>>
>>>> Martin,
>>>>
>>>> Loading will be OK, I expect, if you as root,
>>>> # modprobe agrmodem
>>>> # modprobe agrserial
>>>> Then run
>>>> # ./agrsm-test
>>>>
>>>> The problem which we can fix later is that the /etc/modprobe file/line
>>>> for pre-loading agrmodem before agrserial is not yet present.
>>>> We can fix this later.
>>>>
>>>> Test and report back.
>>>>
>>>> MarvS
>>>>
>>>> On Mon, May 24, 2010 at 10:08 AM, mwl<mossianin_lbcmi@xxxxxxxxxx>
>>>> wrote:
>>>>
>>>>
>>>>> The results of the find show the following:
>>>>> /lib/modules/2.6.32.12-pclos1.bfs/extra/agrmodem.ko
>>>>> /lib/modules/2.6.32.12-pclos1.bfs/extra/agrserial.ko
>>>>>
>>>>> Thanks.
>>>>>
>>>>>
>>>>> On 05/23/2010 05:09 PM, Marvin Stodolsky wrote:
>>>>>
>>>>>
>>>>>> Martin,
>>>>>>
>>>>>> Again check where they installed to with:
>>>>>> $ find /lib/modules -name agr*.ko
>>>>>>
>>>>>> MarvS
>>>>>>
>>>>>> On Sun, May 23, 2010 at 6:32 PM, mwl<mossianin_lbcmi@xxxxxxxxxx>
>>>>>> wrote:
>>>>>>
>>>>>>
>>>>>>
>>>>>>> The following is the results of the install sequence. If I am
>>>>>>> understanding
>>>>>>> correctly, it looks like the driver installed.
>>>>>>>
>>>>>>> [agrsm06pci-2.1.80~20100106]# make clean
>>>>>>> make -C /lib/modules/2.6.32.12-pclos1.bfs/build
>>>>>>> M=/usr/src/agrsm06pci-2.1.80~20100106 clean
>>>>>>> make[1]: Entering directory
>>>>>>> `/usr/src/kernel-devel-2.6.32.12-pclos1.bfs'
>>>>>>> CLEAN /usr/src/agrsm06pci-2.1.80~20100106/.tmp_versions
>>>>>>> CLEAN /usr/src/agrsm06pci-2.1.80~20100106/Module.symvers
>>>>>>> /usr/src/agrsm06pci-2.1.80~20100106/modules.order
>>>>>>> make[1]: Leaving directory
>>>>>>> `/usr/src/kernel-devel-2.6.32.12-pclos1.bfs'
>>>>>>>
>>>>>>> [agrsm06pci-2.1.80~20100106]# make
>>>>>>> make -C /lib/modules/2.6.32.12-pclos1.bfs/build
>>>>>>> M=/usr/src/agrsm06pci-2.1.80~20100106 modules
>>>>>>> make[1]: Entering directory
>>>>>>> `/usr/src/kernel-devel-2.6.32.12-pclos1.bfs'
>>>>>>> CC [M] /usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.o
>>>>>>> /usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c: In function
>>>>>>> ‘agr_pci_find_device’:
>>>>>>> /usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c:364: warning:
>>>>>>> ignoring
>>>>>>> return value of ‘pci_enable_device’, declared with attribute
>>>>>>> warn_unused_result
>>>>>>> /usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c: In function
>>>>>>> ‘x_linux_dbg_print_crit’:
>>>>>>> /usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c:349: warning: the
>>>>>>> frame
>>>>>>> size of 1540 bytes is larger than 1024 bytes
>>>>>>> /usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c: In function
>>>>>>> ‘x_linux_dbg_print’:
>>>>>>> /usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c:337: warning: the
>>>>>>> frame
>>>>>>> size of 1540 bytes is larger than 1024 bytes
>>>>>>> SHIPPED /usr/src/agrsm06pci-2.1.80~20100106/agrmodemlib.o
>>>>>>> CC [M] /usr/src/agrsm06pci-2.1.80~20100106/hda.o
>>>>>>> CC [M] /usr/src/agrsm06pci-2.1.80~20100106/serial26.o
>>>>>>> LD [M] /usr/src/agrsm06pci-2.1.80~20100106/agrmodem.o
>>>>>>> LD [M] /usr/src/agrsm06pci-2.1.80~20100106/agrserial.o
>>>>>>> Building modules, stage 2.
>>>>>>> MODPOST 2 modules
>>>>>>> WARNING: could not find
>>>>>>> /usr/src/agrsm06pci-2.1.80~20100106/.agrmodemlib.o.cmd for
>>>>>>> /usr/src/agrsm06pci-2.1.80~20100106/agrmodemlib.o
>>>>>>> CC /usr/src/agrsm06pci-2.1.80~20100106/agrmodem.mod.o
>>>>>>> LD [M] /usr/src/agrsm06pci-2.1.80~20100106/agrmodem.ko
>>>>>>> CC /usr/src/agrsm06pci-2.1.80~20100106/agrserial.mod.o
>>>>>>> LD [M] /usr/src/agrsm06pci-2.1.80~20100106/agrserial.ko
>>>>>>> make[1]: Leaving directory
>>>>>>> `/usr/src/kernel-devel-2.6.32.12-pclos1.bfs'
>>>>>>>
>>>>>>> [agrsm06pci-2.1.80~20100106]# make module_install
>>>>>>> make: *** No rule to make target `module_install'. Stop.
>>>>>>> [root@localhost agrsm06pci-2.1.80~20100106]# make modules_install
>>>>>>> make -C /lib/modules/2.6.32.12-pclos1.bfs/build
>>>>>>> M=/usr/src/agrsm06pci-2.1.80~20100106 modules_install
>>>>>>> make[1]: Entering directory
>>>>>>> `/usr/src/kernel-devel-2.6.32.12-pclos1.bfs'
>>>>>>> INSTALL /usr/src/agrsm06pci-2.1.80~20100106/agrmodem.ko
>>>>>>> INSTALL /usr/src/agrsm06pci-2.1.80~20100106/agrserial.ko
>>>>>>> DEPMOD 2.6.32.12-pclos1.bfs
>>>>>>> make[1]: Leaving directory
>>>>>>> `/usr/src/kernel-devel-2.6.32.12-pclos1.bfs'
>>>>>>> <<end of install>>
>>>>>>>
>>>>>>> Based on earlier instructions, I then tried the agrsm-test as
>>>>>>> follows:
>>>>>>> [agrsm06pci-2.1.80~20100106]# ./agrsm-test
>>>>>>>
>>>>>>> Found drivers for boot kernel 2.6.32.12-pclos1.bfs at:
>>>>>>> find: paths must precede expression: agrserial.ko
>>>>>>> Usage: find [-H] [-L] [-P] [-Olevel] [-D
>>>>>>> help|tree|search|stat|rates|opt|exec] [path...] [expression]
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> Loading drivers:
>>>>>>> FATAL: Error inserting agrserial
>>>>>>> (/lib/modules/2.6.32.12-pclos1.bfs/extra/agrserial.ko): No such
>>>>>>> device
>>>>>>>
>>>>>>> Checking for utility wvdialconf
>>>>>>> Utility wvdialconf not found
>>>>>>>
>>>>>>> The installation record has been written to ./agrsm-test.txt
>>>>>>> <<end of agrsm-test>>
>>>>>>>
>>>>>>> When I noticed the FATAL, I did find the file(device?) at the
>>>>>>> location
>>>>>>> specified in the error message, so now I am stumped (again).
>>>>>>>
>>>>>>> Because the test noted that wvdial did not exist, I tried using KPPP
>>>>>>> to
>>>>>>> connect and all I get is a message about the modem being busy.
>>>>>>>
>>>>>>> I am trying to get my hands on wvdial, but that requires wvstreams,
>>>>>>> which
>>>>>>> will not install for some reason. So, I thought I would pass along
>>>>>>> what
>>>>>>> I
>>>>>>> can in the hopes that there is enough there to help solve the
>>>>>>> problem.
>>>>>>>
>>>>>>> Thanks.
>>>>>>>
>>>>>>>
>>>>>>> On 05/23/2010 02:54 PM, Marvin Stodolsky wrote:
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>> Martin
>>>>>>>>
>>>>>>>> Use agrsm06pci-2.1.80-20106
>>>>>>>> After the
>>>>>>>> # make clean
>>>>>>>> # make
>>>>>>>> read the Makefile with
>>>>>>>> # more Makefile
>>>>>>>> You will thus see that the command needed is:
>>>>>>>> # make modules_install
>>>>>>>> Why the LSI maintainer choose this variant is obscure.
>>>>>>>>
>>>>>>>> MarvS
>>>>>>>>
>>>>>>>> On Sun, May 23, 2010 at 4:32 PM, mwl<mossianin_lbcmi@xxxxxxxxxx>
>>>>>>>> wrote:
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>> I apologize for the slowness of my responses lately. I have been
>>>>>>>>> waiting
>>>>>>>>> for PCLinux to release a more current kernel to the ones that we
>>>>>>>>> have
>>>>>>>>> been
>>>>>>>>> discussing. Now, they have the 2.6.32 kernel and I have upgraded
>>>>>>>>> the
>>>>>>>>> problem machine to that kernel and have been re-attempting to get
>>>>>>>>> this
>>>>>>>>> Agere
>>>>>>>>> 11c1:0630 modem working.
>>>>>>>>>
>>>>>>>>> I started off with what I believe is the most recent driver
>>>>>>>>> (agrsm06pci-2.1.80-20100106) and executed the following commands
>>>>>>>>> from
>>>>>>>>> the
>>>>>>>>> usr/src directory
>>>>>>>>>
>>>>>>>>> [agrsm06pci-2.1.80~20100106]#make clean
>>>>>>>>> make -C /lib/modules/2.6.32.12-pclos1.bfs/build
>>>>>>>>> M=/usr/src/agrsm06pci-2.1.80~20100106 clean
>>>>>>>>> make[1]: Entering directory
>>>>>>>>> `/usr/src/kernel-devel-2.6.32.12-pclos1.bfs'
>>>>>>>>> CLEAN /usr/src/agrsm06pci-2.1.80~20100106/.tmp_versions
>>>>>>>>> CLEAN /usr/src/agrsm06pci-2.1.80~20100106/Module.symvers
>>>>>>>>> /usr/src/agrsm06pci-2.1.80~20100106/Module.markers
>>>>>>>>> /usr/src/agrsm06pci-2.1.80~20100106/modules.order
>>>>>>>>> make[1]: Leaving directory
>>>>>>>>> `/usr/src/kernel-devel-2.6.32.12-pclos1.bfs'
>>>>>>>>>
>>>>>>>>> [agrsm06pci-2.1.80~20100106]# make
>>>>>>>>> make -C /lib/modules/2.6.32.12-pclos1.bfs/build
>>>>>>>>> M=/usr/src/agrsm06pci-2.1.80~20100106 modules
>>>>>>>>> make[1]: Entering directory
>>>>>>>>> `/usr/src/kernel-devel-2.6.32.12-pclos1.bfs'
>>>>>>>>> CC [M] /usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.o
>>>>>>>>> /usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c: In function
>>>>>>>>> ‘agr_pci_find_device’:
>>>>>>>>> /usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c:364: warning:
>>>>>>>>> ignoring
>>>>>>>>> return value of ‘pci_enable_device’, declared with attribute
>>>>>>>>> warn_unused_result
>>>>>>>>> /usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c: In function
>>>>>>>>> ‘x_linux_dbg_print_crit’:
>>>>>>>>> /usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c:349: warning:
>>>>>>>>> the
>>>>>>>>> frame
>>>>>>>>> size of 1540 bytes is larger than 1024 bytes
>>>>>>>>> /usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c: In function
>>>>>>>>> ‘x_linux_dbg_print’:
>>>>>>>>> /usr/src/agrsm06pci-2.1.80~20100106/agrsoftmodem.c:337: warning:
>>>>>>>>> the
>>>>>>>>> frame
>>>>>>>>> size of 1540 bytes is larger than 1024 bytes
>>>>>>>>> SHIPPED /usr/src/agrsm06pci-2.1.80~20100106/agrmodemlib.o
>>>>>>>>> CC [M] /usr/src/agrsm06pci-2.1.80~20100106/hda.o
>>>>>>>>> CC [M] /usr/src/agrsm06pci-2.1.80~20100106/serial26.o
>>>>>>>>> LD [M] /usr/src/agrsm06pci-2.1.80~20100106/agrmodem.o
>>>>>>>>> LD [M] /usr/src/agrsm06pci-2.1.80~20100106/agrserial.o
>>>>>>>>> Building modules, stage 2.
>>>>>>>>> MODPOST 2 modules
>>>>>>>>> WARNING: could not find
>>>>>>>>> /usr/src/agrsm06pci-2.1.80~20100106/.agrmodemlib.o.cmd for
>>>>>>>>> /usr/src/agrsm06pci-2.1.80~20100106/agrmodemlib.o
>>>>>>>>> CC /usr/src/agrsm06pci-2.1.80~20100106/agrmodem.mod.o
>>>>>>>>> LD [M] /usr/src/agrsm06pci-2.1.80~20100106/agrmodem.ko
>>>>>>>>> CC /usr/src/agrsm06pci-2.1.80~20100106/agrserial.mod.o
>>>>>>>>> LD [M] /usr/src/agrsm06pci-2.1.80~20100106/agrserial.ko
>>>>>>>>> make[1]: Leaving directory
>>>>>>>>> `/usr/src/kernel-devel-2.6.32.12-pclos1.bfs'
>>>>>>>>>
>>>>>>>>> [agrsm06pci-2.1.80~20100106]# make install
>>>>>>>>> make: *** No rule to make target `install'. Stop.
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> I also went back to the agrsm06pci-2.1.80-20090825 version of the
>>>>>>>>> driver
>>>>>>>>> with the following results.
>>>>>>>>>
>>>>>>>>> make clean
>>>>>>>>> rm -f *.a
>>>>>>>>> rm -f *~
>>>>>>>>> rm -f agrmodem.o
>>>>>>>>> rm -f agrmodem.ko
>>>>>>>>> rm -f agrmodem.mod.o
>>>>>>>>> rm -f agrmodem.mod.c
>>>>>>>>> rm -f agrserial.o
>>>>>>>>> rm -f agrserial.ko
>>>>>>>>> rm -f agrserial.mod.o
>>>>>>>>> rm -f agrserial.mod.c
>>>>>>>>> rm -f agrsoftmodem.o
>>>>>>>>> rm -f serial26.o
>>>>>>>>> rm -f HDA.o
>>>>>>>>> rm -f hda.o
>>>>>>>>> rm -f modules.order
>>>>>>>>> rm -f Module.symvers
>>>>>>>>> rm -f Module.markers
>>>>>>>>>
>>>>>>>>> [agrsm06pci-2.1.80~20090825]# make
>>>>>>>>>
>>>>>>>>> Run "make install" to install Agere Systems Soft Modem on your
>>>>>>>>> system.
>>>>>>>>> Run "make uninstall" to remove a previously installed modem.
>>>>>>>>>
>>>>>>>>> [agrsm06pci-2.1.80~20090825]# make install
>>>>>>>>> ./agrinst
>>>>>>>>> Installing Agere Softmodem driver version 2.1.80-Red Flag NE 5.0
>>>>>>>>> some files needed for installation are missing
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> Any help would be appreciated.
>>>>>>>>>
>>>>>>>>> Thanks.
>>>>>>>>>
>>>>>>>>>
>>>
>
