Hi Jaccques, Out of curosity I I just Ran tne command setseraal /dev/modem and the result was that the kernel disabled the IRQ (I think the module crashed) Apr 15 01:15:24 www kernel: irq 185: nobody cared (try booting with the "irqpoll" option) Apr 15 01:15:24 www kernel: [<c044aab3>] __report_bad_irq+0x2b/0x69 Apr 15 01:15:24 www kernel: [<c044aca0>] note_interrupt+0x1af/0x1e7 Apr 15 01:15:24 www kernel: [<f8bc427f>] cnxt_interrupt+0xf/0x20 [hsfosspec] Apr 15 01:15:24 www kernel: [<c044a2e7>] handle_IRQ_event+0x23/0x49 Apr 15 01:15:24 www kernel: [<c044a3c0>] __do_IRQ+0xb3/0xe8 Apr 15 01:15:24 www kernel: [<c04063f4>] do_IRQ+0x93/0xae Apr 15 01:15:24 www kernel: [<c040492e>] common_interrupt+0x1a/0x20 Apr 15 01:15:24 www kernel: [<c0402ccf>] mwait_idle+0x25/0x38 Apr 15 01:15:24 www kernel: [<c0402c90>] cpu_idle+0x9f/0xb9 Apr 15 01:15:24 www kernel: ======================= Apr 15 01:15:24 www kernel: handlers: Apr 15 01:15:24 www kernel: [<c057000f>] (usb_hcd_irq+0x0/0x50) Apr 15 01:15:24 www kernel: [<f88e2ea7>] (ata_interrupt+0x0/0x16a [libata]) Apr 15 01:15:24 www kernel: [<f8bc4270>] (cnxt_interrupt+0x0/0x20 [hsfosspec]) Apr 15 01:15:24 www kernel: Disabling IRQ #185 and next when i try wvdialconf /etc/wvdial.con it gives error ar input/output error Then I tried to reinstall the alsa and hsf (same rpms) but without any joy.Finally I reinserted the modem card and i think it works now:- below are some logs:- [root@www ~]# wvdial /etc/wvdial.conf --> WvDial: Internet dialer version 1.54.0 --> Warning: section [Dialer /etc/wvdial.conf] does not exist in wvdial.conf. --> Initializing modem. --> Sending: ATZ ATZ OK --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 OK --> Modem initialized. --> Sending: ATDTxxxxxx --> Waiting for carrier. ATDT23572514 CONNECT 460800 --> Carrier detected. Starting PPP immediately. --> Starting pppd at Thu Apr 15 02:25:58 2010 --> pid of pppd: 4846 --> Using interface ppp0 --> pppd: es --> pppd: es --> pppd: es --> pppd: es --> pppd: es --> local IP address xxx.xxx.xxx.xxx --> pppd: es --> remote IP address xxx.xxx.xxx.xxx --> pppd: es So I think the problem was related to the loose connection may have happened due to the repeated attempt to jackin and jackout of cables (As previously i was suspecting an issue related to faulty cable rj11 at modem end) Now I am getting a strange message sometimes in my syslog. CCP: timeout sending Config-Requests -- Thanks and Regards, Diptanu Paul EMAIL:- diptanu@xxxxxxxxxxxxxxxxxxxxx "If GNU/Linux does not have any solution... Then you have got a wrong problem....." =======POWER OF OPEN SOURCE======== "If you win, you need not have to explain.... If you loose, you should not be there to explain!" --Adolf Hitler Yes, definitely, the driver does not work. Was this test executed using the hsf driver answering "yes" when offered to use the replacement driver, or using the ALSA driver as recommended for HDA drivers on the Linuxant Web site? Jacques Paul Diptanu wrote: > Hi Jacques, > I tried to connect through the wvdial but got an error. > > First I configured my wvdial > > [root@www etc]# wvdialconf /etc/wvdial.conf > Scanning your serial ports for a modem. > > Port Scan<*1>: Scanning ttySHSF0 first, /dev/modem is a link to it. > ttySHSF0<*1>: ATQ0 V1 E1 -- OK > ttySHSF0<*1>: ATQ0 V1 E1 Z -- OK > ttySHSF0<*1>: ATQ0 V1 E1 S0=0 -- OK > ttySHSF0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK > ttySHSF0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK > ttySHSF0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK > ttySHSF0<*1>: Modem Identifier: ATI -- 56000 > ttySHSF0<*1>: Speed 4800: AT -- OK > ttySHSF0<*1>: Speed 9600: AT -- OK > ttySHSF0<*1>: Speed 19200: AT -- OK > ttySHSF0<*1>: Speed 38400: AT -- OK > ttySHSF0<*1>: Speed 57600: AT -- OK > ttySHSF0<*1>: Speed 115200: AT -- OK > ttySHSF0<*1>: Speed 230400: AT -- OK > ttySHSF0<*1>: Speed 460800: AT -- OK > ttySHSF0<*1>: Max speed is 460800; that should be safe. > ttySHSF0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK > ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud > ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud > ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. > Port Scan<*1>: S1 S2 S3 SHSF1 SHSF2 SHSF3 SHSF4 SHSF5 > Port Scan<*1>: SHSF6 SHSF7 > WvModem<*1>: Cannot get information for serial port. > ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud > ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud > ttyUSB0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. > > Found a modem on /dev/ttySHSF0, using link /dev/modem in config. > Modem configuration written to /etc/wvdial.conf. > ttySHSF0<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0" > [root@www etc]# > > > Now edited the wvdial.conf > [root@www etc]# cat /etc/wvdial.conf > > [Dialer Defaults] > Modem = /dev/modem > Baud = 460800 > Init1 = ATZ > Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > ISDN = 0 > Modem Type = Analog Modem > Phone = xxxxxxxxxx > Username = xxxxx > Password = xxxxx > [root@www etc]# > > Now wehn I am dialing , I am getting the below error.. > [root@www etc]# wvdial > --> WvDial: Internet dialer version 1.54.0 > --> Initializing modem. > --> Sending: ATZ > ATZ > OK > --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > OK > --> Modem initialized. > --> Sending: ATDT04428495504 > --> Waiting for carrier. > ATDT04428495504 > > NO CARRIER > --> No Carrier! Trying again. > --> Sending: ATDT04428495504 > --> Waiting for carrier. > ATDT04428495504 > Caught signal #2! Attempting to exit gracefully... > --> Disconnecting at Thu Apr 15 00:29:58 2010 > [root@www etc]# > > > > My Phone line is working fine and when I m trying the same connection with my windows > machine..its working finr.. > > Request your kind help in this regard.Is it a modem problem?? > > > ---------------------------------------------------------------------------------- This e-mail and any files transmitted with it are for the sole use of the intended recipient(s) and may contain confidential and privileged information. If you are not the intended recipient, please contact the sender by reply e-mail and destroy all copies and the original message. The recipient acknowledges that owner of the www.diptanuinfo.co.cc(or the webmaster/administrator) of the website/mail server,are unable to exercise control or ensure or guarantee the integrity of/overthe contents of the information contained in e-mail transmissions and further acknowledges that any views expressed in this message are those of the individual sender only under all circumstances.Before opening any attachments please check them for viruses and defects. ----------------------------------------------------------------------------------
