Ash, The simplest initial route is to shut down, detach all USB devices and reboot, and see if there is more modem info. You can just $ cat /proc/asound/pcm it there is a Modem line in the output. If so proceed with the modem testing. If not Create a file: $ sudo gedit /etc/modprobe.d/blacklist.local with lines: blacklist ehci-hcd # end blacklist Save and reboot. The lower speed USB ports will still work. Check that the blacklisting work with: $ lsmod | grep ehci the ehci-hcd should not be shown. MarvS On Fri, Aug 8, 2008 at 9:01 AM, Ashley Richley <a.a.richley@xxxxxxxxxxxxx> wrote: > Below is the contents of ash.txt as requested. > > Any help is much appreciated. > > ========================================================================================= > > > 00:00.0 Host bridge: nVidia Corporation nForce3 Host Bridge (rev a4) > 00:01.0 ISA bridge: nVidia Corporation nForce3 LPC Bridge (rev a6) > 00:01.1 SMBus: nVidia Corporation nForce3 SMBus (rev a4) > 00:02.0 USB Controller: nVidia Corporation nForce3 USB 1.1 (rev a5) > 00:02.1 USB Controller: nVidia Corporation nForce3 USB 1.1 (rev a5) > 00:02.2 USB Controller: nVidia Corporation nForce3 USB 2.0 (rev a2) > 00:06.0 Multimedia audio controller: nVidia Corporation nForce3 Audio (rev a2) > 00:06.1 Modem: nVidia Corporation nForce3 Audio (rev a2) > 00:08.0 IDE interface: nVidia Corporation nForce3 IDE (rev a5) > 00:0a.0 PCI bridge: nVidia Corporation nForce3 PCI Bridge (rev a2) > 00:0b.0 PCI bridge: nVidia Corporation nForce3 AGP Bridge (rev a4) > 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration > 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map > 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller > 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control > 01:00.0 VGA compatible controller: nVidia Corporation NV17 [GeForce4 420 Go 32M] (rev a3) > 02:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link) > 02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) > 02:02.0 Network controller: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 03) > 02:04.0 CardBus bridge: Texas Instruments PCI1620 PC Card Controller (rev 01) > 02:04.1 CardBus bridge: Texas Instruments PCI1620 PC Card Controller (rev 01) > 02:04.2 System peripheral: Texas Instruments PCI1620 Firmware Loading Function (rev 01) > CPU0 > 0: 3311089 IO-APIC-edge timer > 1: 1563 IO-APIC-edge i8042 > 7: 1 IO-APIC-edge parport0 > 8: 3 IO-APIC-edge rtc > 9: 32103 IO-APIC-fasteoi acpi > 12: 140088 IO-APIC-edge i8042 > 14: 115269 IO-APIC-edge libata > 15: 189724 IO-APIC-edge libata > 16: 4 IO-APIC-fasteoi ohci1394, yenta > 17: 505586 IO-APIC-fasteoi yenta, eth0 > 18: 2481 IO-APIC-fasteoi ehci_hcd:usb3 > 19: 487 IO-APIC-fasteoi ohci_hcd:usb1, NVidia nForce3 > 20: 0 IO-APIC-fasteoi ohci_hcd:usb2 > 21: 23406 IO-APIC-fasteoi b43 > NMI: 0 Non-maskable interrupts > LOC: 262388 Local timer interrupts > RES: 0 Rescheduling interrupts > CAL: 0 function call interrupts > TLB: 0 TLB shootdowns > TRM: 0 Thermal event interrupts > SPU: 0 Spurious interrupts > ERR: 1 > MIS: 0 > [ 0.000000] Initializing cgroup subsys cpuset > [ 0.000000] Initializing cgroup subsys cpu > [ 0.000000] Linux version 2.6.24-19-generic (buildd@terranova) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Fri Jul 11 23:41:49 UTC 2008 (Ubuntu 2.6.24-19.36-generic) > [ 0.000000] BIOS-provided physical RAM map: > [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable) > [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) > [ 0.000000] BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved) > [ 0.000000] BIOS-e820: 0000000000100000 - 000000001ff70000 (usable) > [ 0.000000] BIOS-e820: 000000001ff70000 - 000000001ff7f000 (ACPI data) > [ 0.000000] BIOS-e820: 000000001ff7f000 - 000000001ff80000 (ACPI NVS) > [ 0.000000] BIOS-e820: 000000001ff80000 - 0000000020000000 (reserved) > [ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) > [ 0.000000] 0MB HIGHMEM available. > [ 0.000000] 511MB LOWMEM available. > [ 0.000000] Entering add_active_range(0, 0, 130928) 0 entries of 256 used > [ 0.000000] Zone PFN ranges: > [ 0.000000] DMA 0 -> 4096 > [ 0.000000] Normal 4096 -> 130928 > [ 0.000000] HighMem 130928 -> 130928 > [ 0.000000] Movable zone start PFN for each node > [ 0.000000] early_node_map[1] active PFN ranges > [ 0.000000] 0: 0 -> 130928 > [ 0.000000] On node 0 totalpages: 130928 > [ 0.000000] DMA zone: 32 pages used for memmap > [ 0.000000] DMA zone: 0 pages reserved > [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 > [ 0.000000] Normal zone: 990 pages used for memmap > [ 0.000000] Normal zone: 125842 pages, LIFO batch:31 > [ 0.000000] HighMem zone: 0 pages used for memmap > [ 0.000000] Movable zone: 0 pages used for memmap > [ 0.000000] DMI present. > [ 0.000000] ACPI: RSDP signature @ 0xC00F7280 checksum 0 > [ 0.000000] ACPI: RSDP 000F7280, 0014 (r0 PTLTD ) > [ 0.000000] ACPI: RSDT 1FF7A89F, 0034 (r1 PTLTD RSDT 6040000 LTP 0) > [ 0.000000] ACPI: FACP 1FF7EE34, 0074 (r1 NVIDIA CK8 6040000 PTL_ F4240) > [ 0.000000] ACPI: DSDT 1FF7A8D3, 4561 (r1 NVIDIA CK8 6040000 MSFT 100000E) > [ 0.000000] ACPI: FACS 1FF7FFC0, 0040 > [ 0.000000] ACPI: APIC 1FF7EEA8, 005A (r1 NVIDIA NV_APIC_ 6040000 LTP 0) > [ 0.000000] ACPI: BOOT 1FF7EF02, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1) > [ 0.000000] ACPI: SSDT 1FF7EF2A, 00D6 (r1 PTLTD POWERNOW 6040000 LTP 1) > [ 0.000000] ACPI: DMI detected: Hewlett-Packard > [ 0.000000] Nvidia board detected. Ignoring ACPI timer override. > [ 0.000000] If you got timer trouble try acpi_use_timer_override > [ 0.000000] ACPI: PM-Timer IO Port: 0x8008 > [ 0.000000] ACPI: Local APIC address 0xfee00000 > [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) > [ 0.000000] Processor #0 15:12 APIC version 16 > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) > [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) > [ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > [ 0.000000] ACPI: BIOS IRQ0 pin2 override ignored. > [ 0.000000] ACPI: IRQ9 used by override. > [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs > [ 0.000000] Using ACPI (MADT) for SMP configuration information > [ 0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:dff80000) > [ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000 > [ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000d0000 > [ 0.000000] swsusp: Registered nosave memory region: 00000000000d0000 - 0000000000100000 > [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129906 > [ 0.000000] Kernel command line: root=UUID=604d3330-c5f6-467f-a862-3e03b3d5d877 ro quiet splash > [ 0.000000] mapped APIC to ffffb000 (fee00000) > [ 0.000000] mapped IOAPIC to ffffa000 (fec00000) > [ 0.000000] Enabling fast FPU save and restore... done. > [ 0.000000] Enabling unmasked SIMD FPU exception support... done. > [ 0.000000] Initializing CPU#0 > [ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes) > [ 0.000000] Detected 797.948 MHz processor. > [ 12.681762] spurious 8259A interrupt: IRQ7. > [ 12.683735] Console: colour VGA+ 80x25 > [ 12.683742] console [tty0] enabled > [ 12.684033] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) > [ 12.684582] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) > [ 12.702710] Memory: 507140k/523712k available (2177k kernel code, 15964k reserved, 1006k data, 368k init, 0k highmem) > [ 12.702727] virtual kernel memory layout: > [ 12.702730] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB) > [ 12.702733] pkmap : 0xff800000 - 0xffc00000 (4096 kB) > [ 12.702735] vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB) > [ 12.702738] lowmem : 0xc0000000 - 0xdff70000 ( 511 MB) > [ 12.702741] .init : 0xc0421000 - 0xc047d000 ( 368 kB) > [ 12.702743] .data : 0xc0320474 - 0xc041bdc4 (1006 kB) > [ 12.702746] .text : 0xc0100000 - 0xc0320474 (2177 kB) > [ 12.702753] Checking if this processor honours the WP bit even in supervisor mode... Ok. > [ 12.702812] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1 > [ 12.782825] Calibrating delay using timer specific routine.. 1597.33 BogoMIPS (lpj=3194667) > [ 12.782867] Security Framework initialized > [ 12.782877] SELinux: Disabled at boot. > [ 12.782902] AppArmor: AppArmor initialized > [ 12.782909] Failure registering capabilities with primary security module. > [ 12.782925] Mount-cache hash table entries: 512 > [ 12.783109] Initializing cgroup subsys ns > [ 12.783116] Initializing cgroup subsys cpuacct > [ 12.783132] CPU: After generic identify, caps: 078bfbff c1d3fbff 00000000 00000000 00000000 00000000 00000000 00000000 > [ 12.783149] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) > [ 12.783155] CPU: L2 Cache: 128K (64 bytes/line) > [ 12.783161] CPU: After all inits, caps: 078bfbff c1d3fbff 00000000 00000410 00000000 00000000 00000000 00000000 > [ 12.783178] Compat vDSO mapped to ffffe000. > [ 12.783196] Checking 'hlt' instruction... OK. > [ 12.799427] SMP alternatives: switching to UP code > [ 12.802009] Freeing SMP alternatives: 11k freed > [ 12.802235] Early unpacking initramfs... done > [ 13.556463] ACPI: Core revision 20070126 > [ 13.556575] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found. > [ 13.580902] CPU0: AMD Athlon(tm) XP Processor 2800+ stepping 00 > [ 13.580934] Total of 1 processors activated (1597.33 BogoMIPS). > [ 13.581111] ENABLING IO-APIC IRQs > [ 13.581330] ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1 > [ 13.726756] Brought up 1 CPUs > [ 13.726811] CPU0 attaching sched-domain: > [ 13.726816] domain 0: span 01 > [ 13.726820] groups: 01 > [ 13.727143] net_namespace: 64 bytes > [ 13.727157] Booting paravirtualized kernel on bare hardware > [ 13.728091] Time: 14:37:57 Date: 08/07/08 > [ 13.728136] NET: Registered protocol family 16 > [ 13.728508] EISA bus registered > [ 13.728542] ACPI: bus type pci registered > [ 13.728861] PCI: PCI BIOS revision 2.10 entry at 0xfd8bc, last bus=2 > [ 13.728867] PCI: Using configuration type 1 > [ 13.728885] Setting up standard PCI resources > [ 13.732830] ACPI: EC: Look up EC in DSDT > [ 13.734830] ACPI: Interpreter enabled > [ 13.734837] ACPI: (supports S0 S3 S4 S5) > [ 13.734861] ACPI: Using IOAPIC for interrupt routing > [ 13.783392] ACPI: EC: GPE = 0x21, I/O: command/status = 0x66, data = 0x62 > [ 13.783400] ACPI: EC: driver started in poll mode > [ 13.783498] ACPI: PCI Root Bridge [PCI0] (0000:00) > [ 13.784679] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > [ 13.784814] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT] > [ 13.784884] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP0._PRT] > [ 13.807563] ACPI: PCI Interrupt Link [LNK1] (IRQs 16 18 19) *0 > [ 13.807886] ACPI: PCI Interrupt Link [LNK2] (IRQs 16 18 19) *0 > [ 13.808200] ACPI: PCI Interrupt Link [LNK3] (IRQs 17) *0 > [ 13.808509] ACPI: PCI Interrupt Link [LNK4] (IRQs 16 18 19) *0, disabled. > [ 13.808826] ACPI: PCI Interrupt Link [LNK5] (IRQs 16 18 19) *0 > [ 13.809131] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22) *0 > [ 13.809434] ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22) *0 > [ 13.809738] ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *0 > [ 13.810042] ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22) *0 > [ 13.810346] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22) *0, disabled. > [ 13.810651] ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22) *0 > [ 13.810975] ACPI: PCI Interrupt Link [LMCI] (IRQs 20 21 22) *0 > [ 13.811284] ACPI: PCI Interrupt Link [LPID] (IRQs 20 21 22) *0, disabled. > [ 13.811599] ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22) *0, disabled. > [ 13.811862] Linux Plug and Play Support v0.97 (c) Adam Belay > [ 13.811925] pnp: PnP ACPI init > [ 13.811943] ACPI: bus type pnp registered > [ 13.815154] ACPI: EC: non-query interrupt received, switching to interrupt mode > [ 13.836452] pnp: PnP ACPI: found 13 devices > [ 13.836460] ACPI: ACPI bus type pnp unregistered > [ 13.836467] PnPBIOS: Disabled by ACPI PNP > [ 13.836909] PCI: Using ACPI for IRQ routing > [ 13.836916] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report > [ 13.858669] NET: Registered protocol family 8 > [ 13.858674] NET: Registered protocol family 20 > [ 13.858800] AppArmor: AppArmor Filesystem Enabled > [ 13.862653] Time: tsc clocksource has been installed. > [ 13.870730] system 00:01: ioport range 0x8000-0x807f has been reserved > [ 13.870736] system 00:01: ioport range 0x8080-0x80ff has been reserved > [ 13.870743] system 00:01: ioport range 0x8400-0x847f has been reserved > [ 13.870749] system 00:01: ioport range 0x8480-0x84ff has been reserved > [ 13.870755] system 00:01: ioport range 0x8800-0x887f has been reserved > [ 13.870761] system 00:01: ioport range 0x8880-0x88ff has been reserved > [ 13.870767] system 00:01: ioport range 0x2040-0x207f has been reserved > [ 13.870774] system 00:01: ioport range 0x2000-0x203f has been reserved > [ 13.870790] system 00:02: iomem range 0xfff80000-0xffffffff could not be reserved > [ 13.870797] system 00:02: iomem range 0xfec00000-0xfec00fff has been reserved > [ 13.870804] system 00:02: iomem range 0xfee00000-0xfeefffff has been reserved > [ 13.870811] system 00:02: iomem range 0xfed00000-0xfed00fff has been reserved > [ 13.870823] system 00:03: ioport range 0x200-0x20f has been reserved > [ 13.870830] system 00:03: ioport range 0x680-0x6ff has been reserved > [ 13.870836] system 00:03: ioport range 0x4d0-0x4d1 has been reserved > [ 13.870842] system 00:03: ioport range 0xfe00-0xfe01 has been reserved > [ 13.901660] PCI: Failed to allocate mem resource #10:4000000@ec000000 for 0000:02:04.0 > [ 13.901669] PCI: Failed to allocate mem resource #10:4000000@ec000000 for 0000:02:04.1 > [ 13.901677] PCI: Bus 3, cardbus bridge: 0000:02:04.0 > [ 13.901682] IO window: 00003000-000030ff > [ 13.901689] IO window: 00003400-000034ff > [ 13.901694] PREFETCH window: 30000000-33ffffff > [ 13.901701] PCI: Bus 7, cardbus bridge: 0000:02:04.1 > [ 13.901705] IO window: 00003800-000038ff > [ 13.901710] IO window: 00003c00-00003cff > [ 13.901716] PREFETCH window: 34000000-37ffffff > [ 13.901721] PCI: Bridge: 0000:00:0a.0 > [ 13.901726] IO window: 3000-7fff > [ 13.901731] MEM window: e8100000-e97fffff > [ 13.901737] PREFETCH window: 30000000-37ffffff > [ 13.901744] PCI: Bridge: 0000:00:0b.0 > [ 13.901747] IO window: disabled. > [ 13.901753] MEM window: ea000000-eaffffff > [ 13.901759] PREFETCH window: f8000000-fc0fffff > [ 13.901774] PCI: Setting latency timer of device 0000:00:0a.0 to 64 > [ 13.902287] ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 19 > [ 13.902300] ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNK1] -> GSI 19 (level, low) -> IRQ 16 > [ 13.902734] ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 18 > [ 13.902742] ACPI: PCI Interrupt 0000:02:04.1[B] -> Link [LNK2] -> GSI 18 (level, low) -> IRQ 17 > [ 13.902776] NET: Registered protocol family 2 > [ 13.942782] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) > [ 13.943238] TCP established hash table entries: 16384 (order: 5, 131072 bytes) > [ 13.943411] TCP bind hash table entries: 16384 (order: 5, 131072 bytes) > [ 13.943598] TCP: Hash tables configured (established 16384 bind 16384) > [ 13.943603] TCP reno registered > [ 13.954893] checking if image is initramfs...<7>Switched to high resolution mode on CPU 0 > [ 14.659036] it is > [ 15.417048] Freeing initrd memory: 7326k freed > [ 15.417270] Simple Boot Flag at 0x37 set to 0x1 > [ 15.418165] audit: initializing netlink socket (disabled) > [ 15.418203] audit(1218119878.600:1): initialized > [ 15.421909] VFS: Disk quotas dquot_6.5.1 > [ 15.422051] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > [ 15.422338] io scheduler noop registered > [ 15.422343] io scheduler anticipatory registered > [ 15.422347] io scheduler deadline registered > [ 15.422368] io scheduler cfq registered (default) > [ 15.828785] Boot video device is 0000:01:00.0 > [ 15.829311] isapnp: Scanning for PnP cards... > [ 16.183372] isapnp: No Plug & Play device found > [ 16.244224] Real Time Clock Driver v1.12ac > [ 16.244393] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled > [ 16.245908] ACPI: PCI Interrupt Link [LMCI] enabled at IRQ 22 > [ 16.245924] ACPI: PCI Interrupt 0000:00:06.1[B] -> Link [LMCI] -> GSI 22 (level, low) -> IRQ 18 > [ 16.245939] ACPI: PCI interrupt for device 0000:00:06.1 disabled > [ 16.247275] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize > [ 16.247403] input: Macintosh mouse button emulation as /devices/virtual/input/input0 > [ 16.247596] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 > [ 16.257916] i8042.c: Detected active multiplexing controller, rev 1.1. > [ 16.265240] serio: i8042 KBD port at 0x60,0x64 irq 1 > [ 16.265248] serio: i8042 AUX0 port at 0x60,0x64 irq 12 > [ 16.265254] serio: i8042 AUX1 port at 0x60,0x64 irq 12 > [ 16.265260] serio: i8042 AUX2 port at 0x60,0x64 irq 12 > [ 16.265265] serio: i8042 AUX3 port at 0x60,0x64 irq 12 > [ 16.274069] mice: PS/2 mouse device common for all mice > [ 16.274283] EISA: Probing bus 0 at eisa.0 > [ 16.274295] Cannot allocate resource for EISA slot 1 > [ 16.274300] Cannot allocate resource for EISA slot 2 > [ 16.274304] Cannot allocate resource for EISA slot 3 > [ 16.274309] Cannot allocate resource for EISA slot 4 > [ 16.274313] Cannot allocate resource for EISA slot 5 > [ 16.274317] Cannot allocate resource for EISA slot 6 > [ 16.274322] Cannot allocate resource for EISA slot 7 > [ 16.274326] Cannot allocate resource for EISA slot 8 > [ 16.274330] EISA: Detected 0 cards. > [ 16.274335] cpuidle: using governor ladder > [ 16.274340] cpuidle: using governor menu > [ 16.274495] NET: Registered protocol family 1 > [ 16.274541] Using IPI No-Shortcut mode > [ 16.274593] registered taskstats version 1 > [ 16.274787] Magic number: 4:602:636 > [ 16.274872] hash matches device ptycf > [ 16.274984] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found > [ 16.274988] EDD information not available. > [ 16.275427] Freeing unused kernel memory: 368k freed > [ 16.309959] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 > [ 17.796069] fuse init (API version 7.9) > [ 17.841792] ACPI: CPU0 (power states: C1[C1] C2[C2]) > [ 17.849435] ACPI Exception (thermal-0471): AE_NOT_FOUND, Invalid active threshold [0] [20070126] > [ 17.854499] ACPI: Thermal Zone [THRM] (30 C) > [ 18.701389] usbcore: registered new interface driver usbfs > [ 18.701430] usbcore: registered new interface driver hub > [ 18.715028] usbcore: registered new device driver usb > [ 18.741318] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver > [ 18.741914] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 21 > [ 18.741929] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 21 (level, low) -> IRQ 19 > [ 18.741949] PCI: Setting latency timer of device 0000:00:02.0 to 64 > [ 18.741956] ohci_hcd 0000:00:02.0: OHCI Host Controller > [ 18.742301] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 > [ 18.742336] ohci_hcd 0000:00:02.0: irq 19, io mem 0xe8000000 > [ 18.799467] usb usb1: configuration #1 chosen from 1 choice > [ 18.799516] hub 1-0:1.0: USB hub found > [ 18.799530] hub 1-0:1.0: 3 ports detected > [ 18.901900] ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 20 > [ 18.901917] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS1] -> GSI 20 (level, low) -> IRQ 20 > [ 18.901937] PCI: Setting latency timer of device 0000:00:02.1 to 64 > [ 18.901944] ohci_hcd 0000:00:02.1: OHCI Host Controller > [ 18.901995] ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2 > [ 18.902021] ohci_hcd 0000:00:02.1: irq 20, io mem 0xe8001000 > [ 18.959385] usb usb2: configuration #1 chosen from 1 choice > [ 18.959435] hub 2-0:1.0: USB hub found > [ 18.959449] hub 2-0:1.0: 3 ports detected > [ 19.422168] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 22 > [ 19.422179] ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [LUS2] -> GSI 22 (level, low) -> IRQ 18 > [ 19.422199] PCI: Setting latency timer of device 0000:00:02.2 to 64 > [ 19.422206] ehci_hcd 0000:00:02.2: EHCI Host Controller > [ 19.422262] ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3 > [ 19.422315] PCI: cache line size of 64 is not supported by device 0000:00:02.2 > [ 19.422336] ehci_hcd 0000:00:02.2: irq 18, io mem 0xe8004000 > [ 19.437066] ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 > [ 19.437275] usb usb3: configuration #1 chosen from 1 choice > [ 19.437320] hub 3-0:1.0: USB hub found > [ 19.437337] hub 3-0:1.0: 6 ports detected > [ 19.660186] SCSI subsystem initialized > [ 19.860951] libata version 3.00 loaded. > [ 19.898727] ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 17 > [ 19.898744] ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNK3] -> GSI 17 (level, low) -> IRQ 21 > [ 19.898784] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x04, vendor 0x4243) > [ 19.898794] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x05, vendor 0x4243) > [ 19.898803] ssb: Core 2 found: PCMCIA (cc 0x80D, rev 0x02, vendor 0x4243) > [ 19.898812] ssb: Core 3 found: V90 (cc 0x807, rev 0x02, vendor 0x4243) > [ 19.898820] ssb: Core 4 found: PCI (cc 0x804, rev 0x09, vendor 0x4243) > [ 19.902199] ssb: Sonics Silicon Backplane found on PCI device 0000:02:02.0 > [ 19.941620] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) > [ 19.941683] 8139cp 0000:02:01.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip > [ 19.941691] 8139cp 0000:02:01.0: Try the "8139too" driver instead. > [ 19.972719] PCI: Setting latency timer of device 0000:00:08.0 to 64 > [ 20.035663] pata_amd 0000:00:08.0: version 0.3.10 > [ 20.035740] PCI: Setting latency timer of device 0000:00:08.0 to 64 > [ 20.060891] scsi0 : pata_amd > [ 20.116034] scsi1 : pata_amd > [ 20.117286] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x2080 irq 14 > [ 20.117293] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x2088 irq 15 > [ 20.145903] 8139too Fast Ethernet driver 0.9.28 > [ 20.282894] ata1.00: ATA-6: ST94019A, 3.09, max UDMA/100 > [ 20.282903] ata1.00: 78140160 sectors, multi 16: LBA48 > [ 20.297687] ata1.00: configured for UDMA/100 > [ 20.641126] ata2.00: ATAPI: SD-R2512, 1A04, max MWDMA2 > [ 20.829056] ata2.00: configured for MWDMA2 > [ 20.829250] scsi 0:0:0:0: Direct-Access ATA ST94019A 3.09 PQ: 0 ANSI: 5 > [ 20.834726] scsi 1:0:0:0: CD-ROM TOSHIBA DVD-ROM SD-R2512 1A04 PQ: 0 ANSI: 5 > [ 20.835103] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNK1] -> GSI 19 (level, low) -> IRQ 16 > [ 20.884975] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16] MMIO=[e8108000-e81087ff] Max Packet=[2048] IR/IT contexts=[4/8] > [ 20.895802] ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNK2] -> GSI 18 (level, low) -> IRQ 17 > [ 20.896610] eth0: RealTek RTL8139 at 0x7000, 00:0f:b0:0a:e6:b1, IRQ 17 > [ 20.896615] eth0: Identified 8139 chip type 'RTL-8101' > [ 21.608574] Driver 'sd' needs updating - please use bus_type methods > [ 21.608717] sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB) > [ 21.608743] sd 0:0:0:0: [sda] Write Protect is off > [ 21.608749] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > [ 21.608781] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA > [ 21.609602] sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB) > [ 21.609630] sd 0:0:0:0: [sda] Write Protect is off > [ 21.609635] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > [ 21.609668] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA > [ 21.609676] sda:<4>Driver 'sr' needs updating - please use bus_type methods > [ 21.844596] sda1 sda2 < sda5 > > [ 21.875707] sd 0:0:0:0: [sda] Attached SCSI disk > [ 21.886813] sd 0:0:0:0: Attached scsi generic sg0 type 0 > [ 21.886858] sr 1:0:0:0: Attached scsi generic sg1 type 5 > [ 21.936377] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray > [ 21.936388] Uniform CD-ROM driver Revision: 3.20 > [ 21.936495] sr 1:0:0:0: Attached scsi CD-ROM sr0 > [ 22.164468] ieee1394: Host added: ID:BUS[0-00:1023] GUID[483f0200483f0200] > [ 22.400284] Attempting manual resume > [ 22.400293] swsusp: Resume From Partition 8:5 > [ 22.400297] PM: Checking swsusp image. > [ 22.401548] PM: Resume from disk failed. > [ 22.449784] kjournald starting. Commit interval 5 seconds > [ 22.449806] EXT3-fs: mounted filesystem with ordered data mode. > [ 23.367960] floppy0: no floppy controllers found > [ 37.433930] Linux agpgart interface v0.102 > [ 37.568110] agpgart: Detected AGP bridge 0 > [ 37.568140] agpgart: Setting up Nforce3 AGP. > [ 37.575185] agpgart: AGP aperture is 128M @ 0xf0000000 > [ 37.824060] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x2040 > [ 37.824118] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x2000 > [ 38.077387] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > [ 38.137960] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 > [ 39.478058] input: Power Button (FF) as /devices/virtual/input/input2 > [ 39.487372] ACPI: Power Button (FF) [PWRF] > [ 39.487583] input: Power Button (CM) as /devices/virtual/input/input3 > [ 39.503351] ACPI: Power Button (CM) [PWRB] > [ 39.503553] input: Lid Switch as /devices/virtual/input/input4 > [ 39.512744] ACPI: Lid Switch [LID] > [ 39.561254] ACPI: WMI-Acer: Mapper loaded > [ 39.978368] input: PC Speaker as /devices/platform/pcspkr/input/input5 > [ 43.055500] ACPI: AC Adapter [ACAD] (off-line) > [ 43.670880] ACPI: PCI Interrupt Link [LACI] enabled at IRQ 21 > [ 43.670891] ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LACI] -> GSI 21 (level, low) -> IRQ 19 > [ 43.670927] PCI: Setting latency timer of device 0000:00:06.0 to 64 > [ 43.782127] ALSA /build/buildd/linux-ubuntu-modules-2.6.24-2.6.24/debian/build/build-generic/sound/alsa-driver/pci/ac97/ac97_codec.c:2128: AC'97 0 analog subsections not ready > [ 44.373962] intel8x0_measure_ac97_clock: measured 55285 usecs > [ 44.373971] intel8x0: clocking to 48000 > [ 44.422138] ACPI: Battery Slot [BAT1] (battery present) > [ 44.590826] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:18/LNXVIDEO:00/input/input6 > [ 44.601906] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no) > [ 45.313885] Yenta: CardBus bridge found at 0000:02:04.0 [103c:006d] > [ 45.313910] PCI: Bus 3, cardbus bridge: 0000:02:04.0 > [ 45.313915] IO window: 00003000-000030ff > [ 45.313921] IO window: 00003400-000034ff > [ 45.313927] PREFETCH window: 30000000-33ffffff > [ 45.313933] MEM window: e8400000-e87fffff > [ 45.313940] Yenta: Enabling burst memory read transactions > [ 45.313947] Yenta: Using CSCINT to route CSC interrupts to PCI > [ 45.313951] Yenta: Routing CardBus interrupts to PCI > [ 45.313958] Yenta TI: socket 0000:02:04.0, mfunc 0x01111d22, devctl 0x64 > [ 45.546404] Yenta: ISA IRQ mask 0x0cf0, PCI irq 16 > [ 45.546412] Socket status: 30000086 > [ 45.546418] Yenta: Raising subordinate bus# of parent bus (#02) from #02 to #06 > [ 45.546427] pcmcia: parent PCI bridge I/O window: 0x3000 - 0x7fff > [ 45.546434] cs: IO port probe 0x3000-0x7fff: clean. > [ 45.548722] pcmcia: parent PCI bridge Memory window: 0xe8100000 - 0xe97fffff > [ 45.548728] pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x37ffffff > [ 45.583821] Yenta: CardBus bridge found at 0000:02:04.1 [103c:006d] > [ 45.583846] Yenta: Using CSCINT to route CSC interrupts to PCI > [ 45.583851] Yenta: Routing CardBus interrupts to PCI > [ 45.583859] Yenta TI: socket 0000:02:04.1, mfunc 0x01111d22, devctl 0x64 > [ 45.814333] Yenta: ISA IRQ mask 0x0cf0, PCI irq 17 > [ 45.814341] Socket status: 30000006 > [ 45.814347] Yenta: Raising subordinate bus# of parent bus (#02) from #06 to #0a > [ 45.814356] pcmcia: parent PCI bridge I/O window: 0x3000 - 0x7fff > [ 45.814363] cs: IO port probe 0x3000-0x7fff: clean. > [ 45.816650] pcmcia: parent PCI bridge Memory window: 0xe8100000 - 0xe97fffff > [ 45.816656] pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x37ffffff > [ 46.147289] eth0: link down > [ 46.501494] input: PS/2 Mouse as /devices/virtual/input/input7 > [ 46.534133] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio4/input/input8 > [ 47.513374] parport_pc 00:0b: reported by Plug and Play ACPI > [ 47.513435] parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA] > [ 47.610519] b43-phy0: Broadcom 4306 WLAN found > [ 47.633089] b43-phy0 debug: Found PHY: Analog 2, Type 2, Revision 2 > [ 47.633118] b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2 > [ 47.661189] phy0: Selected rate control algorithm 'simple' > [ 47.952782] NET: Registered protocol family 17 > [ 49.900403] floppy0: no floppy controllers found > [ 50.662217] cs: IO port probe 0x100-0x3af: clean. > [ 50.664129] cs: IO port probe 0x3e0-0x4ff: clean. > [ 50.665021] cs: IO port probe 0x820-0x8ff: clean. > [ 50.665742] cs: IO port probe 0xc00-0xcf7: clean. > [ 50.666767] cs: IO port probe 0xa00-0xaff: clean. > [ 50.667995] cs: IO port probe 0x100-0x3af: clean. > [ 50.669922] cs: IO port probe 0x3e0-0x4ff: clean. > [ 50.670773] cs: IO port probe 0x820-0x8ff: clean. > [ 50.671489] cs: IO port probe 0xc00-0xcf7: clean. > [ 50.672533] cs: IO port probe 0xa00-0xaff: clean. > [ 51.352890] lp0: using parport0 (interrupt-driven). > [ 51.510063] Adding 1510068k swap on /dev/sda5. Priority:-1 extents:1 across:1510068k > [ 51.574345] EXT3 FS on sda1, internal journal > [ 52.766633] ip_tables: (C) 2000-2006 Netfilter Core Team > [ 53.717386] No dock devices found. > [ 54.158762] powernow-k8: Found 1 AMD Athlon(tm) XP Processor 2800+ processors (1 cpu cores) (version 2.20.00) > [ 54.158826] powernow-k8: 0 : fid 0x8 (1600 MHz), vid 0x6 > [ 54.158832] powernow-k8: 1 : fid 0x0 (800 MHz), vid 0x18 > [ 55.596506] apm: BIOS not found. > [ 55.775065] ppdev: user-space parallel port driver > [ 55.963708] audit(1218119919.794:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=4960 profile="/usr/sbin/cupsd" namespace="default" > [ 58.241083] input: b43-phy0 as /devices/virtual/input/input9 > [ 58.462343] Bluetooth: Core ver 2.11 > [ 58.468736] NET: Registered protocol family 31 > [ 58.468745] Bluetooth: HCI device and connection manager initialized > [ 58.468754] Bluetooth: HCI socket layer initialized > [ 58.534878] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02) > [ 58.558835] Bluetooth: L2CAP ver 2.9 > [ 58.558845] Bluetooth: L2CAP socket layer initialized > [ 58.685948] Bluetooth: RFCOMM socket layer initialized > [ 58.685978] Bluetooth: RFCOMM TTY layer initialized > [ 58.685983] Bluetooth: RFCOMM ver 1.8 > [ 59.682157] b43-phy0 debug: Chip initialized > [ 59.682915] b43-phy0 debug: 30-bit DMA initialized > [ 59.686183] Registered led device: b43-phy0:tx > [ 59.686660] Registered led device: b43-phy0:rx > [ 59.687006] Registered led device: b43-phy0:radio > [ 59.687049] b43-phy0 debug: Wireless interface started > [ 59.725878] b43-phy0 debug: Adding Interface type 2 > [ 79.049098] NET: Registered protocol family 10 > [ 79.049993] lo: Disabled Privacy Extensions > [ 79.051224] ADDRCONF(NETDEV_UP): eth0: link is not ready > [ 79.052608] ADDRCONF(NETDEV_UP): wlan0: link is not ready > [ 2513.396748] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 > [ 2513.397057] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready > [ 2523.888791] eth0: no IPv6 routers present > [ 1298.930391] Marking TSC unstable due to: cpufreq changes. > [ 1298.932372] Time: acpi_pm clocksource has been installed. > [ 1299.204110] Clocksource tsc unstable (delta = 272025944 ns) > [68716.648407] usb 3-1: new high speed USB device using ehci_hcd and address 2 > [68716.781327] usb 3-1: configuration #1 chosen from 1 choice > [68717.469208] usbcore: registered new interface driver libusual > [68717.574758] Initializing USB Mass Storage driver... > [68717.584136] scsi2 : SCSI emulation for USB Mass Storage devices > [68717.586603] usbcore: registered new interface driver usb-storage > [68717.587052] USB Mass Storage support registered. > [68717.587657] usb-storage: device found at 2 > [68717.587666] usb-storage: waiting for device to settle before scanning > [68722.582827] usb-storage: device scan complete > [68722.584191] scsi 2:0:0:0: Direct-Access USB2.0 USB Flash Disk 0.00 PQ: 0 ANSI: 2 > [68722.598679] sd 2:0:0:0: [sdb] 1007616 512-byte hardware sectors (516 MB) > [68722.599400] sd 2:0:0:0: [sdb] Write Protect is off > [68722.599411] sd 2:0:0:0: [sdb] Mode Sense: 00 00 00 00 > [68722.599417] sd 2:0:0:0: [sdb] Assuming drive cache: write through > [68722.601267] sd 2:0:0:0: [sdb] 1007616 512-byte hardware sectors (516 MB) > [68722.601894] sd 2:0:0:0: [sdb] Write Protect is off > [68722.601903] sd 2:0:0:0: [sdb] Mode Sense: 00 00 00 00 > [68722.601908] sd 2:0:0:0: [sdb] Assuming drive cache: write through > [68722.601919] sdb: sdb1 > [68722.744781] sd 2:0:0:0: [sdb] Attached SCSI removable disk > [68722.744856] sd 2:0:0:0: Attached scsi generic sg2 type 0 > [68785.333500] usb 3-1: USB disconnect, address 2 > [71305.465759] usb 3-2: new high speed USB device using ehci_hcd and address 3 > [71305.610930] usb 3-2: configuration #1 chosen from 1 choice > [71305.617797] hub 3-2:1.0: USB hub found > [71305.618450] hub 3-2:1.0: 1 port detected > [71305.925803] usb 3-2.1: new high speed USB device using ehci_hcd and address 4 > [71306.030956] usb 3-2.1: configuration #1 chosen from 1 choice > [71306.051698] scsi3 : SCSI emulation for USB Mass Storage devices > [71306.057801] usb-storage: device found at 4 > [71306.057810] usb-storage: waiting for device to settle before scanning > [71312.272010] usb-storage: device scan complete > [71312.273250] scsi 3:0:0:0: Direct-Access Corsair Flash Voyager 1.00 PQ: 0 ANSI: 0 CCS > [71312.283937] sd 3:0:0:0: [sdb] 8011776 512-byte hardware sectors (4102 MB) > [71312.286965] sd 3:0:0:0: [sdb] Write Protect is off > [71312.286978] sd 3:0:0:0: [sdb] Mode Sense: 00 26 00 00 > [71312.286984] sd 3:0:0:0: [sdb] Assuming drive cache: write through > [71312.289954] sd 3:0:0:0: [sdb] 8011776 512-byte hardware sectors (4102 MB) > [71312.292962] sd 3:0:0:0: [sdb] Write Protect is off > [71312.292974] sd 3:0:0:0: [sdb] Mode Sense: 00 26 00 00 > [71312.292979] sd 3:0:0:0: [sdb] Assuming drive cache: write through > [71312.292991] sdb: sdb1 > [71312.294238] sd 3:0:0:0: [sdb] Attached SCSI removable disk > [71312.294323] sd 3:0:0:0: Attached scsi generic sg2 type 0 > [71338.154427] usb 3-2: USB disconnect, address 3 > [71338.154438] usb 3-2.1: USB disconnect, address 4 > [71342.582866] usb 3-2: new high speed USB device using ehci_hcd and address 5 > [71342.716947] usb 3-2: configuration #1 chosen from 1 choice > [71342.765348] scsi4 : SCSI emulation for USB Mass Storage devices > [71342.775052] usb-storage: device found at 5 > [71342.775062] usb-storage: waiting for device to settle before scanning > [71347.773493] usb-storage: device scan complete > [71347.774608] scsi 4:0:0:0: Direct-Access PEAK III Flash Drive 0.00 PQ: 0 ANSI: 2 > [71347.789487] sd 4:0:0:0: [sdb] 16121855 512-byte hardware sectors (8254 MB) > [71347.790195] sd 4:0:0:0: [sdb] Write Protect is off > [71347.790206] sd 4:0:0:0: [sdb] Mode Sense: 00 00 00 00 > [71347.790213] sd 4:0:0:0: [sdb] Assuming drive cache: write through > [71347.793185] sd 4:0:0:0: [sdb] 16121855 512-byte hardware sectors (8254 MB) > [71347.793815] sd 4:0:0:0: [sdb] Write Protect is off > [71347.793825] sd 4:0:0:0: [sdb] Mode Sense: 00 00 00 00 > [71347.793831] sd 4:0:0:0: [sdb] Assuming drive cache: write through > [71347.793842] sdb: sdb1 > [71347.898713] sd 4:0:0:0: [sdb] Attached SCSI removable disk > [71347.898794] sd 4:0:0:0: Attached scsi generic sg2 type 0 > [71437.368458] usb 3-2: USB disconnect, address 5 > > > ========================================================================================= > > Thanks, > > Ash > > > -----Original Message----- > From: Marvin Stodolsky [mailto:marvin.stodolsky@xxxxxxxxx] > Sent: 08 August 2008 13:41 > To: Ashley Richley > Cc: discuss@xxxxxxxxxxxxx > Subject: Re: FW: Trouble with dial up modem on Ubuntu > > Ash, > > Your System seems to have some strange features. Do: > $ lspci >> ash.txt > $ cat /proc/interrupts >> ash.txt > $ dmesg >> ash.txt > and send to the List. > > Do > $ bash -x ./scanModem 2>&1 | tee ashscan.txt > and send just to me, so I can determine why scanModem quit early. > > Run: > $ scanModem fake 10de:00d9 103c:006d > which will access archival information, reporting 10de:00d9 is the > PCI identifier of an AC'97 Modem controller card with an Agere SIL27 > modem chip, rather than an audio card. > > This could be someone's mistake in a the PCI ID datebase, which is the > simplest explanation. Is your Audio working? > > Assuming 103c:006d is in fact your modem, the most immediate problem is: > [ 16.245939] ACPI: PCI interrupt for device 0000:00:06.1 disabled > That is, the card was disabled during the bootup diagnostics. > This is the lead problem to overcome, for which the ash.txt will > provide useful info. > If you do not need USB function, b;ocking loading of the ehci_hcd > driver sharing > interrupt 18 > may suffice to enable the modem. > > Only AFTER enablement, can the standard guidance for this modem Class be useful. > ---------------------- > Download from http://linmodems.technion.ac.il/packages/smartlink/ > the package SLMODEMD.gcc4.2.tar.gz having a compiled slmodemd. Unpack > under Linux with: > $ tar zxf SLMODEMD.gcc4.2.tar.gz > and read instructions therein. But briefly, the modem is setup with command: > sudo slmodemd -c YOUR_COUNTRY --alsa modem:1 > reporting dynamic creation of ports: > /dev/ttySL0 --> /dev/pts/N , with N some number > Read DOCs/Smartlink.txt and Modem/DOCs/YourSystem.txt for follow > through guidance > > If possible, do the modem diagnostics under Microsoft, and copy us the > ATI output responses. SoftModem.txt has details. > > MarvS > scanModem maintainer > > On Fri, Aug 8, 2008 at 5:42 AM, Ashley Richley > <a.a.richley@xxxxxxxxxxxxx> wrote: >> Hi all, >> >> I am a very basic linux user and am trying to adapt my knowledge from just >> windows products into linux. Basically I have an install of ubuntu that I >> set up and am now trying to install and configure the dial up modem. I have >> followed the instructions on the beginner page and have go to the point >> where it tells me to submit ModemData.txt to the discussion board. So below >> is the file contents. >> >> ============================================================================ >> =========================== >> >> Only plain text email is forwarded by the Discuss@xxxxxxxxxxxxx List >> Server, >> as HTML can contain viruses. Use as the email Subject Line: >> YourName, YourCountry kernel 2.6.24-19-generic >> With this Subject Line cogent experts will be alerted, and useful case >> names left in the Archive. >> YourCountry will enable Country specific guidance. Linux experts in >> YourCountry >> can be found through: http://www.linux.org/groups/index.html. >> They will know your Country's modem code, which may be essential for dialup >> service. >> Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an Internet >> Provider mail filters. >> So in a day, also check the Archived responses at http://www.linmodems.org >> -------------------------- System information ---------------------------- >> CPU=i686, >> Linux version 2.6.24-19-generic (buildd@terranova) (gcc version 4.2.3 >> (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Fri Jul 11 23:41:49 UTC 2008 >> scanModem update of: 2008_07_31 >> >> There are no blacklisted modem drivers in /etc/modprobe* files >> USB modems not recognized >> >> For candidate card in slot 00:06.1, firmware information and bootup >> diagnostics are: >> PCI slot PCI ID SubsystemID Name >> ---------- --------- --------- -------------- >> 00:06.1 10de:00d9 103c:006d Modem: nVidia Corporation >> nForce3 Audio >> >> Modem interrupt assignment and sharing: >> 18: 0 IO-APIC-fasteoi ehci_hcd:usb3 >> --- Bootup diagnostics for card in PCI slot 00:06.1 ---- >> [ 16.245924] ACPI: PCI Interrupt 0000:00:06.1[B] -> Link [LMCI] -> GSI 22 >> (level, low) -> IRQ 18 >> [ 16.245939] ACPI: PCI interrupt for device 0000:00:06.1 disabled >> >> The PCI slot 00:06.1 of the modem card may be disabled early in >> a bootup process, but then enabled later. If modem drivers load >> but the modem is not responsive, read DOCs/Bootup.txt about possible >> fixes. >> Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx >> if help is needed. >> >> ============================================================================ >> =========================== >> >> Can someone please point me in the right direction from here? >> >> Thankyou in advance >> >> Ash >> >> > >
