Sebek, modem:0 (or hw:0) is your audio card, while modem:1 (or hw:1) is the mode Use: $ sudo gedit /etc/default/sl-modem-daemon to chamge SLMODEMD_COUNTRY=USA to SLMODEMD_COUNTRY=OMAN also while testing set DONTSTART=1 as you may have interference from those scripts. slamr should not be loaded as it may interfere When the scripts are working properly, they run a slmodemd setup during the bootup, Thus the modem is activated. But if slamr was used, the --alsa modem is not set!! Note that you can do: $ sudo /etc/init.d/sl-modem-daemon stop (or start or restart) The slmodemd installed by the sl-modem-daemon package. It is $ slmodemd --version SmartLink Soft Modem: version 2.9.9e-pre1 ------------ while you need the $ slmodemd --version SmartLink Soft Modem: version 2.9.11 -------------- provided by the SLMODEMD package. Copy the slmodemd from the SLMODEMD package to /usr/bin/slmodemd and there should then be version 2.9.11 $ slmodemd --version SmartLink Soft Modem: version 2.9.11 CHeck these issues out. MarvS On Sun, Mar 9, 2008 at 3:34 AM, Sebek Ab. <sebeeek@xxxxxxxxx> wrote: > Hi Marvin, > > I can still not launch the dial up connection, slmodemd with modem1 > give an error message and slmodemd with hw0 gives me a "no carrier" > message when launching connection. I tried to modprobe -r / modprobe > many times. I tried rebooting. > > Details below : > > sebek@bourdon:~$ sudo modprobe -r snd-intel8x0m > sebek@bourdon:~$ sudo modprobe snd-intel8x0m > sebek@bourdon:~$ sudo slmodemd -c OMAN -a modem:1 > > error: mixer setup: attach hw:1 error: No such device > ALSA lib conf.c:3949:(snd_config_expand) Unknown parameters 1 > ALSA lib pcm.c:2144:(snd_pcm_open_noupdate) Unknown PCM modem:1 > error: alsa setup: cannot open playback device 'modem:1': Invalid argument > error: cannot setup device `modem:1' > > I have the same error message with modem:0 and hw:1 > > With hw:0 I get : > sebek@bourdon:~$ sudo slmodemd -c OMAN -a hw:0 > > error: mixer setup: Off-hook switch not found for card hw:0 > SmartLink Soft Modem: version 2.9.11 Feb 17 2008 09:31:10 > symbolic link `/dev/ttySL0' -> `/dev/pts/2' created. > modem `hw:0' created. TTY is `/dev/pts/2' > > Use `/dev/ttySL0' as modem device, Ctrl+C for termination. > error: cannot set channels for playback: Invalid argument > > When slmodemd is launched with hw:0, the sound is not working. > > If I launched connection when slmodemd is launched with "hw:0" I get : > Mar 9 09:05:29 bourdon chat[6321]: abort on (NO CARRIER) > [...] > Mar 9 09:05:29 bourdon chat[6321]: timeout set to 75 seconds > Mar 9 09:05:29 bourdon chat[6321]: expect (CONNECT) > Mar 9 09:05:29 bourdon chat[6321]: ^M > Mar 9 09:05:29 bourdon chat[6321]: AT&FH0L3^M^M > Mar 9 09:05:29 bourdon chat[6321]: OK^M > Mar 9 09:05:29 bourdon chat[6321]: ATDT122^M^M > Mar 9 09:05:29 bourdon chat[6321]: NO CARRIER > Mar 9 09:05:29 bourdon chat[6321]: -- failed > Mar 9 09:05:29 bourdon chat[6321]: Failed (NO CARRIER) > Mar 9 09:05:30 bourdon pppd[6260]: Exit. > > Following recommendations when a "no carrier" error occurs : > http://linmodems.technion.ac.il/archive-fifth/msg00552.html > I updated my (empty) module.conf and added : > > options snd cards_limit=2 > alias snd-card-0 snd-intel8x0 > alias sound-slot-0 snd-intel8x0 > options snd-intel8x0 index=0 > alias snd-card-1 snd-intel8x0m > alias sound-slot-1 snd-intel8x0m > options snd-intel8x0m index=1 > > still the same situation. > > Should I still try to use modem0? Or try to fix this no carrier message first? > > Thank you for your help, > BR > > By the way I don't have access anymore to > http://linmodems.technion.ac.il/ (timeout). Is it down or should I > blame my very-low dial up connection? > > 2008/3/7, Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx>: > > > > Sebek, > > > > Copy the slmodemd into the COMMAND path > > $ sudo cp slmodemd /usr/sbin/slmodemd > > $ sudo chmod +x /usr/sbin/slmodemd > > > > When the problem below occurs just unload and reload the driver > > $ sudo modprobe -r snd-intel8x0m > > $ sudo modprobe snd-intel8x0m > > This usually cures sucj failures (once you have had a success). It is > > occassionally needed between dialout sessions. > > > > MarvS > > > > > > > > On Thu, Mar 6, 2008 at 11:55 AM, Sebek Ab. <sebeeek@xxxxxxxxx> wrote: > > > Thank you Marvin for your useful answer, > > > > > > I downloaded SLMODEMD.gcc4.1, uninstalled the ubuntu slmodem, > > > extracted the tgz, sudo modprobe snd-intel8x0m, did a sudo ./slmodemd > > > -c OMAN --alsa modem:1 and parallely to that send a ppp connection > > > (via network manager). > > > And actually it worked ! I downloaded my e-mails and was able to surf the web. > > > > > > Great job ! ... but > > > Since I rebooted my computer it is not working anymore. > > > > > > The module is correctly loaded : > > > sebek@bourdon:~/tmp/SLMODEMD.gcc4.1$ lsmod|grep intel > > > snd_intel8x0m 18572 0 > > > snd_intel8x0 34972 1 > > > snd_ac97_codec 100644 2 snd_intel8x0m,snd_intel8x0 > > > snd_pcm 80388 4 > > > snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss > > > snd 54660 13 > > > snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device > > > snd_page_alloc 11400 3 snd_intel8x0m,snd_intel8x0,snd_pcm > > > intel_agp 25620 1 > > > agpgart 35016 2 drm,intel_agp > > > > > > but when I launch slmodem with the same command than previously, I get > > > an error message: > > > > > > sebek@bourdon:~/tmp/SLMODEMD.gcc4.1$ sudo ./slmodemd -c OMAN -a modem:1 > > > error: mixer setup: attach hw:1 error: No such device > > > ALSA lib conf.c:3949:(snd_config_expand) Unknown parameters 1 > > > ALSA lib pcm.c:2144:(snd_pcm_open_noupdate) Unknown PCM modem:1 > > > error: alsa setup: cannot open playback device 'modem:1': Invalid argument > > > error: cannot setup device `modem:1' > > > > > > I tried with modem:0 and modem:1, with hw:0 and with hw:1 > > > > > > Only the hw:1 is launched correctly : > > > sebek@bourdon:~/tmp/SLMODEMD.gcc4.1$ sudo ./slmodemd -c OMAN -a hw:0 > > > error: mixer setup: Off-hook switch not found for card hw:0 > > > SmartLink Soft Modem: version 2.9.11 Feb 17 2008 09:31:10 > > > symbolic link `/dev/ttySL0' -> `/dev/pts/3' created. > > > modem `hw:0' created. TTY is `/dev/pts/3' > > > Use `/dev/ttySL0' as modem device, Ctrl+C for termination. > > > > > > but then nothing happens when connecting with network-manager (nothing > > > in messages). Reading the Slmodem-ALSA.txt I should anyway use the > > > "modem" and not the "hw". > > > As you told me in the previous e-mail, I also tried to bring all > > > network interfaces down and unplug all usb devices. It does not help. > > > > > > sebek@bourdon:~/tmp/SLMODEMD.gcc4.1$ alsactl --version > > > alsactl version 1.0.14 > > > > > > sebek@bourdon:~/tmp/SLMODEMD.gcc4.1$ ll /dev/modem > > > lrwxrwxrwx 1 root root 11 2008-03-06 17:33 /dev/modem -> /dev/ttySL0 > > > > > > Do you have an explanation for this error message when launching > > > slmodemd while it was working this morning? > > > > > > Thank you > > > > > > 2008/3/4, Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx>: > > > > > > > > > > RE: [ 128.172292] slamr: SmartLink AMRMO modem. > > > > > > > > [ 128.172535] slamr: probe 8086:24c6 ICH4 card... > > > > [ 128.175251] slamr: mc97 codec is SIL27 > > > > [ 128.175340] slamr: slamr0 is ICH4 card. > > > > > > > > > > > > > > > > While slamr is doing a good diagnostic, the > > > > mc97 codec is SIL27 > > > > reveals that slamr is the wrong driver. > > > > > > > > > > > > Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 > > > > > > > > Modem Controller should be support by the driver snd-inte8x0m plus an > > > > ALSA competent slmodemd. For this testing phase remove the > > > > sl-modem-daemon package, as it will confuse issues: > > > > $ sudo apt-get remove sl-modem-daemon > > > > > > > > Rather, download from http://linmodems.technion.ac.il/packages/smartlink/ > > > > the package SLMODEMD.gcc4.1.tar.gz having a compiled slmodemd. Unpack > > > > under Linux with: > > > > $ tar zxf SLMODEMD.gcc4.1.tar.gz > > > > and read instructions therein. But briefly, the modem is setup commands: > > > > $ sudo modprobe snd-intel8x0m > > > > $ sudo slmodemd -c YOUR_COUNTRY --alsa modem:1 > > > > reporting dynamic creation of ports: > > > > /dev/ttySL0 --> /dev/pts/N , with N some number > > > > Read Smartlink.txt and Modem/YourSystem.txt for follow through guidance. > > > > > > > > There may be a problem with > > > > ------------------- > > > > Modem interrupt assignment and sharing: > > > > 10: 1469276 XT-PIC-XT uhci_hcd:usb1, ohci1394, ICH4, > > > > Intel 82801DB-ICH4, eth0, radeon@pci:0000:01:00.0 > > > > ---------------------- > > > > in that the sharing seems to be failing, in particular the > > > > radeon@pci:0000:01:00.0 indicates a dominant hold by the video card. > > > > Detaching non-essential USB devices and > > > > $ sudo ifconfig eth0 down > > > > might relieve competition > > > > > > > > Read the Bootup. txt about possible cures. Additionally, we have a > > > > report about a modem success under Mandriva whereas the same System > > > > under Ubuntu had problems. > > > > > > > > RE The error message "lsmod utility not found!" > > > > > > > > is wrong as I am currently using it. > > > > > > > > ---------- > > > > Yes this is a bug I'll fix tonight > > > > > > > > MarvS > > > > scanModem maintainer > > > > > > > > > > > > > > > > > > > > On Tue, Mar 4, 2008 at 1:33 AM, Sebek Ab. <sebeeek@xxxxxxxxx> wrote: > > > > > Good Morning List, > > > > > > > > > > I have a HP compaq nx7000 laptop with an internal modem but I can't > > > > > have the dialup connection working under Ubuntu Gutsy with kernel > > > > > 2.6.22-14-generic. > > > > > > > > > > Lspci shows : > > > > > 00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) > > > > > AC'97 Modem Controller (rev 01) (prog-if 00 [Generic]) > > > > > Subsystem: Compaq Computer Corporation Unknown device 0860 > > > > > Flags: bus master, medium devsel, latency 0, IRQ 10 > > > > > I/O ports at 4400 [size=256] > > > > > I/O ports at 4800 [size=128] > > > > > Capabilities: [50] Power Management version 2 > > > > > > > > > > scanModem does not create any files like intel.txt or smartlink.txt ... > > > > > I attached the ModemData file created. I also tried to launch the > > > > > scanModem as super user. The error message "lsmod utility not found!" > > > > > is wrong as I am currently using it. > > > > > > > > > > As I have read on the web that my laptop modem would be working with > > > > > smartlink drivers, I tried to install > > > > > slamr-2.6.22-14-generic.tar.gz taken from > > > > > http://linmodems.techion.ac.il/packages/smartlink/Ubuntu/ > > > > > I copied both kernel modules slamr.ko and ungrab-winmodem.ko to > > > > > /lib/modules/2.6.22-14-generic/ and installed package > > > > > sl-modem-daemon_2.9.10+2.9.9d+e-pre2-5build1_i386.deb. Modules are > > > > > loaded correctly. > > > > > > > > > > When I launch the connection with network-manager, it times out : > > > > > (excerpt from messages) : > > > > > Mar 3 11:06:04 bourdon kernel: [ 1875.016000] PPP generic driver version 2.4.2 > > > > > Mar 3 11:06:04 bourdon pppd[7457]: pppd 2.4.4 started by root, uid 0 > > > > > Mar 3 11:06:05 bourdon chat[7484]: timeout set to 60 seconds > > > > > Mar 3 11:06:05 bourdon chat[7484]: abort on (ERROR) > > > > > Mar 3 11:06:05 bourdon chat[7484]: abort on (BUSY) > > > > > Mar 3 11:06:05 bourdon chat[7484]: abort on (VOICE) > > > > > Mar 3 11:06:05 bourdon chat[7484]: abort on (NO CARRIER) > > > > > Mar 3 11:06:05 bourdon chat[7484]: abort on (NO DIALTONE) > > > > > Mar 3 11:06:05 bourdon chat[7484]: abort on (NO DIAL TONE) > > > > > Mar 3 11:06:05 bourdon chat[7484]: abort on (NO ANSWER) > > > > > Mar 3 11:06:05 bourdon chat[7484]: send (ATZ^M) > > > > > Mar 3 11:06:05 bourdon chat[7484]: send (AT&FH0L3^M) > > > > > Mar 3 11:06:05 bourdon chat[7484]: expect (OK) > > > > > Mar 3 11:06:05 bourdon chat[7484]: ATZ^M^M > > > > > Mar 3 11:06:05 bourdon chat[7484]: OK > > > > > Mar 3 11:06:05 bourdon chat[7484]: -- got it > > > > > Mar 3 11:06:05 bourdon chat[7484]: send (ATDT122^M) > > > > > Mar 3 11:06:06 bourdon chat[7484]: timeout set to 75 seconds > > > > > Mar 3 11:06:06 bourdon chat[7484]: expect (CONNECT) > > > > > Mar 3 11:06:06 bourdon chat[7484]: ^M > > > > > Mar 3 11:06:06 bourdon chat[7484]: AT&FH0L3^M^M > > > > > Mar 3 11:06:06 bourdon chat[7484]: OK^M > > > > > Mar 3 11:06:06 bourdon chat[7484]: ATDT122^M^M > > > > > Mar 3 11:07:21 bourdon chat[7484]: alarm > > > > > Mar 3 11:07:21 bourdon chat[7484]: Failed > > > > > Mar 3 11:07:22 bourdon pppd[7457]: Exit. > > > > > > > > > > some more logs : > > > > > sebek@bourdon:~$ dmesg |grep slamr > > > > > [ 128.164704] slamr: module license 'Smart Link Ltd.' taints kernel. > > > > > [ 128.172292] slamr: SmartLink AMRMO modem. > > > > > [ 128.172535] slamr: probe 8086:24c6 ICH4 card... > > > > > [ 128.175251] slamr: mc97 codec is SIL27 > > > > > [ 128.175340] slamr: slamr0 is ICH4 card. > > > > > > > > > > sebek@bourdon:~$ slmodemd > > > > > error: mdm setup: cannot open dev `/dev/slamr0': Device or resource busy > > > > > error: cannot setup device `/dev/slamr0' > > > > > > > > > > sebek@bourdon:~$ ll /dev/slamr0 > > > > > crw-rw---- 1 root dialout 242, 0 2008-03-04 09:00 /dev/slamr0 > > > > > > > > > > > > > > > One important point, I am using the same dial up connection with > > > > > another ubuntu laptop and succeed (sony vaio C2S with hsfmodem), so > > > > > the dial up connection is working and I am using the same connection > > > > > info. > > > > > > > > > > My questions are the following : > > > > > - why is scanModem script not able to detect my modem? > > > > > - is smartlink driver installed correctly? > > > > > > > > > > Thank you for your help, > > > > > Best Regards > > > > > > > > > > > > > > >
