Hi Marvin, Thank you for your patience. As you though, I still had the slamr module loaded, I am not sure why. I fixed the problem with : $ sudo modprobe slamr $ sudo modprobe -r snd_intel8x0m $ sudo modprobe snd_intel8x0m and now I have slmodemd launching correctly : sebek@bourdon:~$ sudo slmodemd -d 1 -c OMAN -a modem:1 SmartLink Soft Modem: version 2.9.11 Feb 17 2008 09:31:10 <419.083677> SmartLink Soft Modem: version 2.9.11 Feb 17 2008 09:31:10 <419.083740> modem:1: startup modem... <419.083853> modem:1: update termios... symbolic link `/dev/ttySL0' -> `/dev/pts/1' created. modem `modem:1' created. TTY is `/dev/pts/1' <419.084485> open file: /var/lib/slmodem/data.modem:1... <419.084537> cannot open '/var/lib/slmodem/data.modem:1': No such file or directory <419.085134> main: rt applyed: SCHED_FIFO, pri 99 Use `/dev/ttySL0' as modem device, Ctrl+C for termination. But I now have a different problem, I always get a "no carrier" message when launching the connection. sebek@bourdon:~$ sudo wvdial WvDial<*1>: WvDial: Internet dialer version 1.56 WvModem<*1>: Cannot get information for serial port. WvDial<*1>: Initializing modem. WvDial<*1>: Sending: ATZ WvDial Modem<*1>: ATZ WvDial Modem<*1>: OK WvDial<*1>: Modem initialized. WvDial<*1>: Sending: ATDT122 WvDial<*1>: Waiting for carrier. WvDial Modem<*1>: ATDT122 WvDial Modem<*1>: CONNECT 40000 WvDial<*1>: Carrier detected. Waiting for prompt. WvDial<Err>: Connected, but carrier signal lost! Retrying... WvDial<*1>: Sending: ATDT122 WvDial<*1>: Waiting for carrier. WvDial Modem<*1>: Authorized Access Only WvDial Modem<*1>: This system is the property of YemenNet PTC WvDial Modem<*1>: Disconnect IMMEDIATELY if you are not an authorized user! WvDial Modem<*1>: User Access Verification WvDial Modem<*1>: Password: WvDial Modem<*1>: Password: WvDial<*1>: Carrier detected. Waiting for prompt. WvDial<Err>: Connected, but carrier signal lost! Retrying... WvDial<*1>: Sending: ATDT122 WvDial<*1>: Waiting for carrier. WvDial Modem<*1>: NO CARRIER WvDial Modem<*1>: ATDT122 WvDial<Warn>: No Carrier! Trying again. WvDial<*1>: Sending: ATDT122 WvDial<*1>: Waiting for carrier. and so on ... Should I blame slmodemd or my wvdial configuration? I have the same problem when using "sudo pon". On another ubuntu computer (using hsfmodem) I don't have any problems. Please find attached the output of the slmodemd launched with debug : slmodemd-output-nocarrier.txt when this no carrier problem occurs. Thank you for any direction you can give me. 2008/3/9, Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx>: > Sebek, > > modem:0 (or hw:0) is your audio card, while modem:1 (or hw:1) is the mode > > Use: > $ sudo gedit /etc/default/sl-modem-daemon > to chamge > SLMODEMD_COUNTRY=USA > to > SLMODEMD_COUNTRY=OMAN > also while testing set > DONTSTART=1 > as you may have interference from those scripts. slamr should not be > loaded as it may interfere > When the scripts are working properly, they run a slmodemd setup > during the bootup, > Thus the modem is activated. But if slamr was used, the --alsa modem > is not set!! > > Note that you can do: > $ sudo /etc/init.d/sl-modem-daemon stop (or start or restart) > > The slmodemd installed by the sl-modem-daemon package. It is > $ slmodemd --version > SmartLink Soft Modem: version 2.9.9e-pre1 > ------------ > > while you need the > $ slmodemd --version > > SmartLink Soft Modem: version 2.9.11 > > -------------- > provided by the SLMODEMD package. > Copy the slmodemd from the SLMODEMD package to /usr/bin/slmodemd and > there should then be version 2.9.11 > $ slmodemd --version > > SmartLink Soft Modem: version 2.9.11 > > > CHeck these issues out. > > MarvS > > > > > > > > > On Sun, Mar 9, 2008 at 3:34 AM, Sebek Ab. <sebeeek@xxxxxxxxx> wrote: > > Hi Marvin, > > > > I can still not launch the dial up connection, slmodemd with modem1 > > give an error message and slmodemd with hw0 gives me a "no carrier" > > message when launching connection. I tried to modprobe -r / modprobe > > many times. I tried rebooting. > > > > Details below : > > > > sebek@bourdon:~$ sudo modprobe -r snd-intel8x0m > > sebek@bourdon:~$ sudo modprobe snd-intel8x0m > > sebek@bourdon:~$ sudo slmodemd -c OMAN -a modem:1 > > > > error: mixer setup: attach hw:1 error: No such device > > ALSA lib conf.c:3949:(snd_config_expand) Unknown parameters 1 > > ALSA lib pcm.c:2144:(snd_pcm_open_noupdate) Unknown PCM modem:1 > > error: alsa setup: cannot open playback device 'modem:1': Invalid argument > > error: cannot setup device `modem:1' > > > > I have the same error message with modem:0 and hw:1 > > > > With hw:0 I get : > > sebek@bourdon:~$ sudo slmodemd -c OMAN -a hw:0 > > > > error: mixer setup: Off-hook switch not found for card hw:0 > > SmartLink Soft Modem: version 2.9.11 Feb 17 2008 09:31:10 > > symbolic link `/dev/ttySL0' -> `/dev/pts/2' created. > > modem `hw:0' created. TTY is `/dev/pts/2' > > > > Use `/dev/ttySL0' as modem device, Ctrl+C for termination. > > error: cannot set channels for playback: Invalid argument > > > > When slmodemd is launched with hw:0, the sound is not working. > > > > If I launched connection when slmodemd is launched with "hw:0" I get : > > Mar 9 09:05:29 bourdon chat[6321]: abort on (NO CARRIER) > > [...] > > Mar 9 09:05:29 bourdon chat[6321]: timeout set to 75 seconds > > Mar 9 09:05:29 bourdon chat[6321]: expect (CONNECT) > > Mar 9 09:05:29 bourdon chat[6321]: ^M > > Mar 9 09:05:29 bourdon chat[6321]: AT&FH0L3^M^M > > Mar 9 09:05:29 bourdon chat[6321]: OK^M > > Mar 9 09:05:29 bourdon chat[6321]: ATDT122^M^M > > Mar 9 09:05:29 bourdon chat[6321]: NO CARRIER > > Mar 9 09:05:29 bourdon chat[6321]: -- failed > > Mar 9 09:05:29 bourdon chat[6321]: Failed (NO CARRIER) > > Mar 9 09:05:30 bourdon pppd[6260]: Exit. > > > > Following recommendations when a "no carrier" error occurs : > > http://linmodems.technion.ac.il/archive-fifth/msg00552.html > > I updated my (empty) module.conf and added : > > > > options snd cards_limit=2 > > alias snd-card-0 snd-intel8x0 > > alias sound-slot-0 snd-intel8x0 > > options snd-intel8x0 index=0 > > alias snd-card-1 snd-intel8x0m > > alias sound-slot-1 snd-intel8x0m > > options snd-intel8x0m index=1 > > > > still the same situation. > > > > Should I still try to use modem0? Or try to fix this no carrier message first? > > > > Thank you for your help, > > BR > > > > By the way I don't have access anymore to > > http://linmodems.technion.ac.il/ (timeout). Is it down or should I > > blame my very-low dial up connection? > > > > 2008/3/7, Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx>: > > > > > > > Sebek, > > > > > > Copy the slmodemd into the COMMAND path > > > $ sudo cp slmodemd /usr/sbin/slmodemd > > > $ sudo chmod +x /usr/sbin/slmodemd > > > > > > When the problem below occurs just unload and reload the driver > > > $ sudo modprobe -r snd-intel8x0m > > > $ sudo modprobe snd-intel8x0m > > > This usually cures sucj failures (once you have had a success). It is > > > occassionally needed between dialout sessions. > > > > > > MarvS > > > > > > > > > > > > On Thu, Mar 6, 2008 at 11:55 AM, Sebek Ab. <sebeeek@xxxxxxxxx> wrote: > > > > Thank you Marvin for your useful answer, > > > > > > > > I downloaded SLMODEMD.gcc4.1, uninstalled the ubuntu slmodem, > > > > extracted the tgz, sudo modprobe snd-intel8x0m, did a sudo ./slmodemd > > > > -c OMAN --alsa modem:1 and parallely to that send a ppp connection > > > > (via network manager). > > > > And actually it worked ! I downloaded my e-mails and was able to surf the web. > > > > > > > > Great job ! ... but > > > > Since I rebooted my computer it is not working anymore. > > > > > > > > The module is correctly loaded : > > > > sebek@bourdon:~/tmp/SLMODEMD.gcc4.1$ lsmod|grep intel > > > > snd_intel8x0m 18572 0 > > > > snd_intel8x0 34972 1 > > > > snd_ac97_codec 100644 2 snd_intel8x0m,snd_intel8x0 > > > > snd_pcm 80388 4 > > > > snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss > > > > snd 54660 13 > > > > snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device > > > > snd_page_alloc 11400 3 snd_intel8x0m,snd_intel8x0,snd_pcm > > > > intel_agp 25620 1 > > > > agpgart 35016 2 drm,intel_agp > > > > > > > > but when I launch slmodem with the same command than previously, I get > > > > an error message: > > > > > > > > sebek@bourdon:~/tmp/SLMODEMD.gcc4.1$ sudo ./slmodemd -c OMAN -a modem:1 > > > > error: mixer setup: attach hw:1 error: No such device > > > > ALSA lib conf.c:3949:(snd_config_expand) Unknown parameters 1 > > > > ALSA lib pcm.c:2144:(snd_pcm_open_noupdate) Unknown PCM modem:1 > > > > error: alsa setup: cannot open playback device 'modem:1': Invalid argument > > > > error: cannot setup device `modem:1' > > > > > > > > I tried with modem:0 and modem:1, with hw:0 and with hw:1 > > > > > > > > Only the hw:1 is launched correctly : > > > > sebek@bourdon:~/tmp/SLMODEMD.gcc4.1$ sudo ./slmodemd -c OMAN -a hw:0 > > > > error: mixer setup: Off-hook switch not found for card hw:0 > > > > SmartLink Soft Modem: version 2.9.11 Feb 17 2008 09:31:10 > > > > symbolic link `/dev/ttySL0' -> `/dev/pts/3' created. > > > > modem `hw:0' created. TTY is `/dev/pts/3' > > > > Use `/dev/ttySL0' as modem device, Ctrl+C for termination. > > > > > > > > but then nothing happens when connecting with network-manager (nothing > > > > in messages). Reading the Slmodem-ALSA.txt I should anyway use the > > > > "modem" and not the "hw". > > > > As you told me in the previous e-mail, I also tried to bring all > > > > network interfaces down and unplug all usb devices. It does not help. > > > > > > > > sebek@bourdon:~/tmp/SLMODEMD.gcc4.1$ alsactl --version > > > > alsactl version 1.0.14 > > > > > > > > sebek@bourdon:~/tmp/SLMODEMD.gcc4.1$ ll /dev/modem > > > > lrwxrwxrwx 1 root root 11 2008-03-06 17:33 /dev/modem -> /dev/ttySL0 > > > > > > > > Do you have an explanation for this error message when launching > > > > slmodemd while it was working this morning? > > > > > > > > Thank you > > > > > > > > 2008/3/4, Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx>: > > > > > > > > > > > > > RE: [ 128.172292] slamr: SmartLink AMRMO modem. > > > > > > > > > > [ 128.172535] slamr: probe 8086:24c6 ICH4 card... > > > > > [ 128.175251] slamr: mc97 codec is SIL27 > > > > > [ 128.175340] slamr: slamr0 is ICH4 card. > > > > > > > > > > > > > > > > > > > > While slamr is doing a good diagnostic, the > > > > > mc97 codec is SIL27 > > > > > reveals that slamr is the wrong driver. > > > > > > > > > > > > > > > Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 > > > > > > > > > > Modem Controller should be support by the driver snd-inte8x0m plus an > > > > > ALSA competent slmodemd. For this testing phase remove the > > > > > sl-modem-daemon package, as it will confuse issues: > > > > > $ sudo apt-get remove sl-modem-daemon > > > > > > > > > > Rather, download from http://linmodems.technion.ac.il/packages/smartlink/ > > > > > the package SLMODEMD.gcc4.1.tar.gz having a compiled slmodemd. Unpack > > > > > under Linux with: > > > > > $ tar zxf SLMODEMD.gcc4.1.tar.gz > > > > > and read instructions therein. But briefly, the modem is setup commands: > > > > > $ sudo modprobe snd-intel8x0m > > > > > $ sudo slmodemd -c YOUR_COUNTRY --alsa modem:1 > > > > > reporting dynamic creation of ports: > > > > > /dev/ttySL0 --> /dev/pts/N , with N some number > > > > > Read Smartlink.txt and Modem/YourSystem.txt for follow through guidance. > > > > > > > > > > There may be a problem with > > > > > ------------------- > > > > > Modem interrupt assignment and sharing: > > > > > 10: 1469276 XT-PIC-XT uhci_hcd:usb1, ohci1394, ICH4, > > > > > Intel 82801DB-ICH4, eth0, radeon@pci:0000:01:00.0 > > > > > ---------------------- > > > > > in that the sharing seems to be failing, in particular the > > > > > radeon@pci:0000:01:00.0 indicates a dominant hold by the video card. > > > > > Detaching non-essential USB devices and > > > > > $ sudo ifconfig eth0 down > > > > > might relieve competition > > > > > > > > > > Read the Bootup. txt about possible cures. Additionally, we have a > > > > > report about a modem success under Mandriva whereas the same System > > > > > under Ubuntu had problems. > > > > > > > > > > RE The error message "lsmod utility not found!" > > > > > > > > > > is wrong as I am currently using it. > > > > > > > > > > ---------- > > > > > Yes this is a bug I'll fix tonight > > > > > > > > > > MarvS > > > > > scanModem maintainer > > > > > > > > > > > > > > > > > > > > > > > > > On Tue, Mar 4, 2008 at 1:33 AM, Sebek Ab. <sebeeek@xxxxxxxxx> wrote: > > > > > > Good Morning List, > > > > > > > > > > > > I have a HP compaq nx7000 laptop with an internal modem but I can't > > > > > > have the dialup connection working under Ubuntu Gutsy with kernel > > > > > > 2.6.22-14-generic. > > > > > > > > > > > > Lspci shows : > > > > > > 00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) > > > > > > AC'97 Modem Controller (rev 01) (prog-if 00 [Generic]) > > > > > > Subsystem: Compaq Computer Corporation Unknown device 0860 > > > > > > Flags: bus master, medium devsel, latency 0, IRQ 10 > > > > > > I/O ports at 4400 [size=256] > > > > > > I/O ports at 4800 [size=128] > > > > > > Capabilities: [50] Power Management version 2 > > > > > > > > > > > > scanModem does not create any files like intel.txt or smartlink.txt ... > > > > > > I attached the ModemData file created. I also tried to launch the > > > > > > scanModem as super user. The error message "lsmod utility not found!" > > > > > > is wrong as I am currently using it. > > > > > > > > > > > > As I have read on the web that my laptop modem would be working with > > > > > > smartlink drivers, I tried to install > > > > > > slamr-2.6.22-14-generic.tar.gz taken from > > > > > > http://linmodems.techion.ac.il/packages/smartlink/Ubuntu/ > > > > > > I copied both kernel modules slamr.ko and ungrab-winmodem.ko to > > > > > > /lib/modules/2.6.22-14-generic/ and installed package > > > > > > sl-modem-daemon_2.9.10+2.9.9d+e-pre2-5build1_i386.deb. Modules are > > > > > > loaded correctly. > > > > > > > > > > > > When I launch the connection with network-manager, it times out : > > > > > > (excerpt from messages) : > > > > > > Mar 3 11:06:04 bourdon kernel: [ 1875.016000] PPP generic driver version 2.4.2 > > > > > > Mar 3 11:06:04 bourdon pppd[7457]: pppd 2.4.4 started by root, uid 0 > > > > > > Mar 3 11:06:05 bourdon chat[7484]: timeout set to 60 seconds > > > > > > Mar 3 11:06:05 bourdon chat[7484]: abort on (ERROR) > > > > > > Mar 3 11:06:05 bourdon chat[7484]: abort on (BUSY) > > > > > > Mar 3 11:06:05 bourdon chat[7484]: abort on (VOICE) > > > > > > Mar 3 11:06:05 bourdon chat[7484]: abort on (NO CARRIER) > > > > > > Mar 3 11:06:05 bourdon chat[7484]: abort on (NO DIALTONE) > > > > > > Mar 3 11:06:05 bourdon chat[7484]: abort on (NO DIAL TONE) > > > > > > Mar 3 11:06:05 bourdon chat[7484]: abort on (NO ANSWER) > > > > > > Mar 3 11:06:05 bourdon chat[7484]: send (ATZ^M) > > > > > > Mar 3 11:06:05 bourdon chat[7484]: send (AT&FH0L3^M) > > > > > > Mar 3 11:06:05 bourdon chat[7484]: expect (OK) > > > > > > Mar 3 11:06:05 bourdon chat[7484]: ATZ^M^M > > > > > > Mar 3 11:06:05 bourdon chat[7484]: OK > > > > > > Mar 3 11:06:05 bourdon chat[7484]: -- got it > > > > > > Mar 3 11:06:05 bourdon chat[7484]: send (ATDT122^M) > > > > > > Mar 3 11:06:06 bourdon chat[7484]: timeout set to 75 seconds > > > > > > Mar 3 11:06:06 bourdon chat[7484]: expect (CONNECT) > > > > > > Mar 3 11:06:06 bourdon chat[7484]: ^M > > > > > > Mar 3 11:06:06 bourdon chat[7484]: AT&FH0L3^M^M > > > > > > Mar 3 11:06:06 bourdon chat[7484]: OK^M > > > > > > Mar 3 11:06:06 bourdon chat[7484]: ATDT122^M^M > > > > > > Mar 3 11:07:21 bourdon chat[7484]: alarm > > > > > > Mar 3 11:07:21 bourdon chat[7484]: Failed > > > > > > Mar 3 11:07:22 bourdon pppd[7457]: Exit. > > > > > > > > > > > > some more logs : > > > > > > sebek@bourdon:~$ dmesg |grep slamr > > > > > > [ 128.164704] slamr: module license 'Smart Link Ltd.' taints kernel. > > > > > > [ 128.172292] slamr: SmartLink AMRMO modem. > > > > > > [ 128.172535] slamr: probe 8086:24c6 ICH4 card... > > > > > > [ 128.175251] slamr: mc97 codec is SIL27 > > > > > > [ 128.175340] slamr: slamr0 is ICH4 card. > > > > > > > > > > > > sebek@bourdon:~$ slmodemd > > > > > > error: mdm setup: cannot open dev `/dev/slamr0': Device or resource busy > > > > > > error: cannot setup device `/dev/slamr0' > > > > > > > > > > > > sebek@bourdon:~$ ll /dev/slamr0 > > > > > > crw-rw---- 1 root dialout 242, 0 2008-03-04 09:00 /dev/slamr0 > > > > > > > > > > > > > > > > > > One important point, I am using the same dial up connection with > > > > > > another ubuntu laptop and succeed (sony vaio C2S with hsfmodem), so > > > > > > the dial up connection is working and I am using the same connection > > > > > > info. > > > > > > > > > > > > My questions are the following : > > > > > > - why is scanModem script not able to detect my modem? > > > > > > - is smartlink driver installed correctly? > > > > > > > > > > > > Thank you for your help, > > > > > > Best Regards > > > > > > > > > > > > > > > > > > > > >
<664.131143> SmartLink Soft Modem: version 2.9.11 Feb 17 2008 09:31:10 <664.131231> modem:1: startup modem... <664.131326> modem:1: update termios... symbolic link `/dev/ttySL0' -> `/dev/pts/1' created. modem `modem:1' created. TTY is `/dev/pts/1' <664.131891> open file: /var/lib/slmodem/data.modem:1... <664.131917> cannot open '/var/lib/slmodem/data.modem:1': No such file or directory <664.132476> main: rt applyed: SCHED_FIFO, pri 99 Use `/dev/ttySL0' as modem device, Ctrl+C for termination. <668.441101> main: termios changed. <668.441139> modem:1: update termios... <668.501727> main: termios changed. <668.501787> modem:1: update termios... <668.601918> modem:1: run cmd: ATZ <668.601970> modem:1: modem reset... <668.601985> modem:1: modem set state: 1 --> 1... <668.602000> modem:1: modem set mode: -> 0... <668.602012> modem:1: modem report result: 0 (OK) <668.702237> modem:1: run cmd: ATDT122 <668.702297> modem:1: modem dial: T122... <668.702312> modem:1: modem_dial_start... <668.702367> modem:1: modem_start.. <668.702382> modem:1: modem set state: 1 --> 2... <668.702395> modem:1: new state: DP_ESTAB <668.702406> main: alsa_ioctl: cmd 8, arg 3... <668.702482> modem:1: modem set hook: 0 --> 1... <668.702498> main: alsa_ioctl: cmd 2, arg 1... <668.702535> main: alsa_ioctl: cmd 11, arg 0... <668.702876> main: alsa_ioctl: cmd 4, arg 2580... <668.702893> main: alsa_ioctl: cmd 7, arg 30... <668.702905> main: alsa_start... Hooks PCM Its setup is: stream : PLAYBACK access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Slave: Hardware PCM card 1 'Intel 82801DB-ICH4 Modem' device 0 subdevice 0 Its setup is: stream : PLAYBACK access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Hooks PCM Its setup is: stream : CAPTURE access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Slave: Hardware PCM card 1 'Intel 82801DB-ICH4 Modem' device 0 subdevice 0 Its setup is: stream : CAPTURE access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 <668.704361> main: startup write: 384... <678.860057> modem:1: 97440: change dp: --> 8... <681.720259> main: alsa_ioctl: cmd 10, arg 0... <681.720318> main: delay = 424 <681.720333> modem:1: 124896: change dp: --> 90... <681.723984> main: alsa_ioctl: cmd 10, arg 0... <681.724005> main: delay = 424 <681.725174> main: change delay -48... <681.730174> main: change delay -48... <681.735172> main: change delay -48... <681.740174> main: change delay -40... <683.595455> main: change delay +384... <697.836489> modem:1: modem_update_status: 256 <697.836549> modem:1: --> DP LINK <697.836562> modem:1: modem set state: 2 --> 4... <697.836576> modem:1: new state: EC_ESTAB <697.896113> modem:1: detector start... <698.046506> modem:1: rx pattern: 0xa2. <698.046548> modem:1: rx pattern: 0xc2. <698.046562> modem:1: rx pattern: 0xa2. <698.051123> modem:1: detector finished. <698.051140> modem:1: modem_update_status: 1024 <698.051152> modem:1: --> PACK LINK <698.051163> modem:1: hdlc_start... <698.216513> modem:1: hdlc frame fcs error. <698.511529> modem:1: hdlc frame fcs error. <699.276573> modem:1: hdlc frame fcs error. <700.761664> modem:1: hdlc frame size error. <701.671715> modem:1: modem update config... <701.671768> modem:1: ec = 1 (1) <701.671782> modem:1: ec_detector = 1 (1) <701.671793> modem:1: ec_tx_win_size = 15 (15) <701.671805> modem:1: ec_rx_win_size = 15 (15) <701.671816> modem:1: ec_tx_info_size = 128 (128) <701.671828> modem:1: ec_rx_info_size = 128 (128) <701.671839> modem:1: comp = 3 (3) <701.671851> modem:1: comp_dict_size = 2048 (2048) <701.671862> modem:1: comp_max_string = 32 (34) <701.806737> modem:1: modem_update_status: 4096 <701.806759> modem:1: --> EC LINK <701.806771> modem:1: modem set state: 4 --> 5... <701.806784> modem:1: new state: MODEM_ONLINE <701.806795> modem:1: modem report result: 1 (CONNECT) <701.806826> main: alsa_ioctl: cmd 8, arg 0... <705.366528> main: change delay -48... <705.371534> main: change delay -48... <705.376535> main: change delay -48... <705.381539> main: change delay -48... <705.386530> main: change delay -48... <705.391536> main: change delay -48... <705.396532> main: change delay -48... <705.401531> main: change delay -48... <708.531910> modem:1: modem_update_status: 4 <708.531968> modem:1: --> FINISH. <708.531981> modem:1: modem_hup... <708.531993> modem:1: modem set state: 5 --> 9... <708.532005> modem:1: new state: DP_DISC <708.532017> modem:1: modem_stop.. <708.532028> main: alsa_stop... <708.532127> modem:1: modem set hook: 1 --> 0... <708.532144> main: alsa_ioctl: cmd 2, arg 0... <708.532182> main: alsa_ioctl: cmd 8, arg 0... <708.532767> modem:1: modem set state: 9 --> 1... <708.532785> modem:1: new state: MODEM_IDLE <708.532797> modem:1: modem report result: 3 (NO CARRIER) <708.532821> main: dev write = 0 <708.830119> modem:1: run cmd: ATDT122 <708.830177> modem:1: modem dial: T122... <708.830192> modem:1: modem_dial_start... <708.830248> modem:1: modem_start.. <708.830263> modem:1: modem set state: 1 --> 2... <708.830276> modem:1: new state: DP_ESTAB <708.830287> main: alsa_ioctl: cmd 8, arg 3... <708.830358> modem:1: modem set hook: 0 --> 1... <708.830374> main: alsa_ioctl: cmd 2, arg 1... <708.830403> main: alsa_ioctl: cmd 11, arg 0... <708.830602> main: alsa_ioctl: cmd 4, arg 2580... <708.830616> main: alsa_ioctl: cmd 7, arg 30... <708.830628> main: alsa_start... Hooks PCM Its setup is: stream : PLAYBACK access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Slave: Hardware PCM card 1 'Intel 82801DB-ICH4 Modem' device 0 subdevice 0 Its setup is: stream : PLAYBACK access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Hooks PCM Its setup is: stream : CAPTURE access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Slave: Hardware PCM card 1 'Intel 82801DB-ICH4 Modem' device 0 subdevice 0 Its setup is: stream : CAPTURE access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 <708.832045> main: startup write: 384... <713.052371> modem:1: modem_update_status: 32 <713.052440> modem:1: --> FINISH. <713.052454> modem:1: modem_hup... <713.052466> modem:1: modem set state: 2 --> 9... <713.052479> modem:1: new state: DP_DISC <713.052490> modem:1: modem_stop.. <713.052501> main: alsa_stop... <713.052573> modem:1: modem set hook: 1 --> 0... <713.052590> main: alsa_ioctl: cmd 2, arg 0... <713.052626> main: alsa_ioctl: cmd 8, arg 0... <713.052687> modem:1: modem set state: 9 --> 1... <713.052702> modem:1: new state: MODEM_IDLE <713.052714> modem:1: modem report result: 7 (BUSY) <713.052740> main: dev write = 0 <713.350123> modem:1: run cmd: ATDT122 <713.350185> modem:1: modem dial: T122... <713.350199> modem:1: modem_dial_start... <713.350254> modem:1: modem_start.. <713.350269> modem:1: modem set state: 1 --> 2... <713.350282> modem:1: new state: DP_ESTAB <713.350293> main: alsa_ioctl: cmd 8, arg 3... <713.350364> modem:1: modem set hook: 0 --> 1... <713.350380> main: alsa_ioctl: cmd 2, arg 1... <713.350408> main: alsa_ioctl: cmd 11, arg 0... <713.350607> main: alsa_ioctl: cmd 4, arg 2580... <713.350621> main: alsa_ioctl: cmd 7, arg 30... <713.350633> main: alsa_start... Hooks PCM Its setup is: stream : PLAYBACK access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Slave: Hardware PCM card 1 'Intel 82801DB-ICH4 Modem' device 0 subdevice 0 Its setup is: stream : PLAYBACK access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Hooks PCM Its setup is: stream : CAPTURE access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Slave: Hardware PCM card 1 'Intel 82801DB-ICH4 Modem' device 0 subdevice 0 Its setup is: stream : CAPTURE access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 <713.352038> main: startup write: 384... <717.052282> modem:1: modem_update_status: 32 <717.052339> modem:1: --> FINISH. <717.052353> modem:1: modem_hup... <717.052364> modem:1: modem set state: 2 --> 9... <717.052377> modem:1: new state: DP_DISC <717.052389> modem:1: modem_stop.. <717.052400> main: alsa_stop... <717.052471> modem:1: modem set hook: 1 --> 0... <717.052488> main: alsa_ioctl: cmd 2, arg 0... <717.052525> main: alsa_ioctl: cmd 8, arg 0... <717.052586> modem:1: modem set state: 9 --> 1... <717.052602> modem:1: new state: MODEM_IDLE <717.052614> modem:1: modem report result: 7 (BUSY) <717.052638> main: dev write = 0 <717.350098> modem:1: run cmd: ATDT122 <717.350158> modem:1: modem dial: T122... <717.350172> modem:1: modem_dial_start... <717.350226> modem:1: modem_start.. <717.350242> modem:1: modem set state: 1 --> 2... <717.350254> modem:1: new state: DP_ESTAB <717.350266> main: alsa_ioctl: cmd 8, arg 3... <717.350326> modem:1: modem set hook: 0 --> 1... <717.350342> main: alsa_ioctl: cmd 2, arg 1... <717.350370> main: alsa_ioctl: cmd 11, arg 0... <717.350570> main: alsa_ioctl: cmd 4, arg 2580... <717.350584> main: alsa_ioctl: cmd 7, arg 30... <717.350595> main: alsa_start... Hooks PCM Its setup is: stream : PLAYBACK access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Slave: Hardware PCM card 1 'Intel 82801DB-ICH4 Modem' device 0 subdevice 0 Its setup is: stream : PLAYBACK access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Hooks PCM Its setup is: stream : CAPTURE access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Slave: Hardware PCM card 1 'Intel 82801DB-ICH4 Modem' device 0 subdevice 0 Its setup is: stream : CAPTURE access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 <717.351938> main: startup write: 384... <721.052200> modem:1: modem_update_status: 32 <721.052266> modem:1: --> FINISH. <721.052281> modem:1: modem_hup... <721.052343> modem:1: modem set state: 2 --> 9... <721.052359> modem:1: new state: DP_DISC <721.052371> modem:1: modem_stop.. <721.052383> main: alsa_stop... <721.052455> modem:1: modem set hook: 1 --> 0... <721.052473> main: alsa_ioctl: cmd 2, arg 0... <721.052510> main: alsa_ioctl: cmd 8, arg 0... <721.052572> modem:1: modem set state: 9 --> 1... <721.052588> modem:1: new state: MODEM_IDLE <721.052599> modem:1: modem report result: 7 (BUSY) <721.052624> main: dev write = 0 <721.350084> modem:1: run cmd: ATDT122 <721.350154> modem:1: modem dial: T122... <721.350170> modem:1: modem_dial_start... <721.350226> modem:1: modem_start.. <721.350242> modem:1: modem set state: 1 --> 2... <721.350255> modem:1: new state: DP_ESTAB <721.350266> main: alsa_ioctl: cmd 8, arg 3... <721.350327> modem:1: modem set hook: 0 --> 1... <721.350342> main: alsa_ioctl: cmd 2, arg 1... <721.350371> main: alsa_ioctl: cmd 11, arg 0... <721.350571> main: alsa_ioctl: cmd 4, arg 2580... <721.350585> main: alsa_ioctl: cmd 7, arg 30... <721.350597> main: alsa_start... Hooks PCM Its setup is: stream : PLAYBACK access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Slave: Hardware PCM card 1 'Intel 82801DB-ICH4 Modem' device 0 subdevice 0 Its setup is: stream : PLAYBACK access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Hooks PCM Its setup is: stream : CAPTURE access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Slave: Hardware PCM card 1 'Intel 82801DB-ICH4 Modem' device 0 subdevice 0 Its setup is: stream : CAPTURE access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 <721.351954> main: startup write: 384... <725.052218> modem:1: modem_update_status: 32 <725.052282> modem:1: --> FINISH. <725.052318> modem:1: modem_hup... <725.052332> modem:1: modem set state: 2 --> 9... <725.052345> modem:1: new state: DP_DISC <725.052356> modem:1: modem_stop.. <725.052367> main: alsa_stop... <725.052440> modem:1: modem set hook: 1 --> 0... <725.052457> main: alsa_ioctl: cmd 2, arg 0... <725.052494> main: alsa_ioctl: cmd 8, arg 0... <725.052555> modem:1: modem set state: 9 --> 1... <725.052571> modem:1: new state: MODEM_IDLE <725.052583> modem:1: modem report result: 7 (BUSY) <725.052607> main: dev write = 0 <725.350146> modem:1: run cmd: ATDT122 <725.350208> modem:1: modem dial: T122... <725.350222> modem:1: modem_dial_start... <725.350277> modem:1: modem_start.. <725.350345> modem:1: modem set state: 1 --> 2... <725.350361> modem:1: new state: DP_ESTAB <725.350372> main: alsa_ioctl: cmd 8, arg 3... <725.350433> modem:1: modem set hook: 0 --> 1... <725.350449> main: alsa_ioctl: cmd 2, arg 1... <725.350477> main: alsa_ioctl: cmd 11, arg 0... <725.350678> main: alsa_ioctl: cmd 4, arg 2580... <725.350692> main: alsa_ioctl: cmd 7, arg 30... <725.350704> main: alsa_start... Hooks PCM Its setup is: stream : PLAYBACK access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Slave: Hardware PCM card 1 'Intel 82801DB-ICH4 Modem' device 0 subdevice 0 Its setup is: stream : PLAYBACK access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Hooks PCM Its setup is: stream : CAPTURE access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Slave: Hardware PCM card 1 'Intel 82801DB-ICH4 Modem' device 0 subdevice 0 Its setup is: stream : CAPTURE access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 <725.352070> main: startup write: 384... <729.052359> modem:1: modem_update_status: 32 <729.052433> modem:1: --> FINISH. <729.052448> modem:1: modem_hup... <729.052459> modem:1: modem set state: 2 --> 9... <729.052472> modem:1: new state: DP_DISC <729.052484> modem:1: modem_stop.. <729.052495> main: alsa_stop... <729.052569> modem:1: modem set hook: 1 --> 0... <729.052586> main: alsa_ioctl: cmd 2, arg 0... <729.052624> main: alsa_ioctl: cmd 8, arg 0... <729.052686> modem:1: modem set state: 9 --> 1... <729.052702> modem:1: new state: MODEM_IDLE <729.052714> modem:1: modem report result: 7 (BUSY) <729.052738> main: dev write = 0 <729.349988> modem:1: run cmd: ATDT122 <729.350041> modem:1: modem dial: T122... <729.350049> modem:1: modem_dial_start... <729.350083> modem:1: modem_start.. <729.350090> modem:1: modem set state: 1 --> 2... <729.350097> modem:1: new state: DP_ESTAB <729.350102> main: alsa_ioctl: cmd 8, arg 3... <729.350165> modem:1: modem set hook: 0 --> 1... <729.350173> main: alsa_ioctl: cmd 2, arg 1... <729.350188> main: alsa_ioctl: cmd 11, arg 0... <729.350285> main: alsa_ioctl: cmd 4, arg 2580... <729.350292> main: alsa_ioctl: cmd 7, arg 30... <729.350297> main: alsa_start... Hooks PCM Its setup is: stream : PLAYBACK access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Slave: Hardware PCM card 1 'Intel 82801DB-ICH4 Modem' device 0 subdevice 0 Its setup is: stream : PLAYBACK access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Hooks PCM Its setup is: stream : CAPTURE access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Slave: Hardware PCM card 1 'Intel 82801DB-ICH4 Modem' device 0 subdevice 0 Its setup is: stream : CAPTURE access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 <729.351049> main: startup write: 384... <733.051339> modem:1: modem_update_status: 32 <733.051414> modem:1: --> FINISH. <733.051428> modem:1: modem_hup... <733.051440> modem:1: modem set state: 2 --> 9... <733.051453> modem:1: new state: DP_DISC <733.051464> modem:1: modem_stop.. <733.051475> main: alsa_stop... <733.051551> modem:1: modem set hook: 1 --> 0... <733.051568> main: alsa_ioctl: cmd 2, arg 0... <733.051606> main: alsa_ioctl: cmd 8, arg 0... <733.051667> modem:1: modem set state: 9 --> 1... <733.051683> modem:1: new state: MODEM_IDLE <733.051695> modem:1: modem report result: 7 (BUSY) <733.051720> main: dev write = 0 <733.354148> modem:1: run cmd: ATDT122 <733.354209> modem:1: modem dial: T122... <733.354224> modem:1: modem_dial_start... <733.354279> modem:1: modem_start.. <733.354294> modem:1: modem set state: 1 --> 2... <733.354307> modem:1: new state: DP_ESTAB <733.354318> main: alsa_ioctl: cmd 8, arg 3... <733.354379> modem:1: modem set hook: 0 --> 1... <733.354394> main: alsa_ioctl: cmd 2, arg 1... <733.354423> main: alsa_ioctl: cmd 11, arg 0... <733.354623> main: alsa_ioctl: cmd 4, arg 2580... <733.354637> main: alsa_ioctl: cmd 7, arg 30... <733.354649> main: alsa_start... Hooks PCM Its setup is: stream : PLAYBACK access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Slave: Hardware PCM card 1 'Intel 82801DB-ICH4 Modem' device 0 subdevice 0 Its setup is: stream : PLAYBACK access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Hooks PCM Its setup is: stream : CAPTURE access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 Slave: Hardware PCM card 1 'Intel 82801DB-ICH4 Modem' device 0 subdevice 0 Its setup is: stream : CAPTURE access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 1 rate : 9600 exact rate : 9600 (9600/1) msbits : 16 buffer_size : 1536 period_size : 48 period_time : 5000 tick_time : 4000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 4 xfer_align : 4 start_threshold : 2147483647 stop_threshold : 1536 silence_threshold: 0 silence_size : 0 boundary : 1610612736 <733.356050> main: startup write: 384... <738.361434> modem:1: modem_update_status: 16 <738.361503> modem:1: --> FINISH. <738.361517> modem:1: modem_hup... <738.361529> modem:1: modem set state: 2 --> 9... <738.361541> modem:1: new state: DP_DISC <738.361553> modem:1: modem_stop.. <738.361564> main: alsa_stop... <738.361637> modem:1: modem set hook: 1 --> 0... <738.361654> main: alsa_ioctl: cmd 2, arg 0... <738.361691> main: alsa_ioctl: cmd 8, arg 0... <738.361741> modem:1: modem set state: 9 --> 1... <738.361757> modem:1: new state: MODEM_IDLE <738.361796> modem:1: modem report result: 6 (NO DIALTONE) <738.361824> main: dev write = 0 <738.462450> main: termios changed. <738.462485> modem:1: update termios... <738.462503> main: pty closed. <772.270127> main: signal 2: mark termination. <772.270211> modem:1: modem_delete... SmartLink Soft Modem: version 2.9.11 Feb 17 2008 09:31:10
