Anita, RE: If I may be so bold as to collaborate on this effort, I noticed the following lines in the logfile: <102.812335> open file: /var/lib/slmodem/data.hw:0,6... <102.812400> cannot open '/var/lib/slmodem/data.hw:0,6': No such file or directory ------------- This is seen also with functioning modems and is not important. The outstanding problem begins here: <124.211995> main: alsa_start... error: cannot setup hw params for playback: Invalid argument <124.212186> err: hw:0,6: modem start = -22: cannot start device. <124.212210> hw:0,6: modem_stop.. All you have done is technically correct. The next thing to try is upgrading snd-hda-intel and its dependent driver set. Give a first read to the example http://linmodems.technion.ac.il/archive-seventh/msg00282.html You will need to download from http://www.alsa-project.org/main/index.php/Main_Page The packages alsa-driver-1.0.16 and alsa-lib-1.0.16 $ mkdir alsa $ cd alsa unpack with ( ../ means the next higher folder) $ tar jxf ../alsa-*.tar.bz2 which will unpack both packages. Move into the driver folder $ cd alsa-driver-1.0.16 Browsen a bit, then do $ ./configure --with-cards=hda-intel If the configuration is successful, the driver set will be compiled with: $ make Get some coffee, this will take a while Do nothing in the alsa-lib-1.0.16/ folder. But it is used during the compile. The new driver set is displayed by: $ ls modules and installed by $ sudo make install THen reboot and retest the modem MarvS On Thu, Mar 6, 2008 at 10:10 PM, Anita Kuno <ay.kuno@xxxxxxxxx> wrote: > Some excellent diagnostic questions, thank you. > > I am dual booted. The modem/phone-line combination, that you are > helping to make work with feisty, is the same one that I am using to > communicate with you now. > > I am attaching the logfile. It is wordy. > > If I may be so bold as to collaborate on this effort, I noticed the > following lines in the logfile: > <102.812335> open file: /var/lib/slmodem/data.hw:0,6... > <102.812400> cannot open '/var/lib/slmodem/data.hw:0,6': No such file or > directory > > So I went looking for /var/lib/slmodem/data.hw:0,6 and I couldn't find it. > anita@anitas-computer:~$ cd / > anita@anitas-computer:/$ cd /var/lib > anita@anitas-computer:/var/lib$ ls > acpi-support dhcp3 logrotate synaptic > alsa dictionaries-common misc ucf > apt doc-base mozilla-firefox update-manager > aptitude dpkg mozilla-thunderbird update-notifier > aspell gcj-4.1 NetworkManager urandom > avahi-autoipd gconf python-support vim > belocs gdm scrollkeeper x11 > binfmts gstreamer security xkb > bittorrent initramfs-tools sgml-base xml-core > dbus initscripts slocate > defoma locales snmp > anita@anitas-computer:/var/lib$ > > So what step was supposed to create a directory and file in /var/lib ? > It seems that step did not have the expected result. > Or perhaps I am wrong? > > Thanks, > > > Anita. > > Marvin Stodolsky wrote: > > Anita, > > First, can you verify that your phone is Touch Tone dial rather than > > the older PULSE type? > > 2) Make sure an ordinary phone dials out on the line you are using, or > > that the modem works under Microsoft. > > > > 3) use the following setup > > $ sudo slmodemd -c CANADA -a --debug=2 --log hw:0,6 > > > > Then in the 2nd console the usual > > $ sudo wvdial > > > > After the failure, send us the generated logfile > > > > MarvS > > > > > > On Thu, Mar 6, 2008 at 9:10 PM, Anita Kuno <ay.kuno@xxxxxxxxx> wrote: > > > >> Thank you for the suggestion, Marvin. > >> > >> I tried this: > >> > >> [Dialer Defaults] > >> Init1 = ATZ > >> Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > >> Modem Type = Analog Modem > >> Baud = 460800 > >> Modem = /dev/ttySL0 > >> ISDN = 0 > >> Phone = 7054579564 > >> Password = XXXXXXXX #protected for the purpose of the email > >> Username = XXXXXXXX #protected for the purpose of the email > >> Carrier Check = no > >> > >> And got this: > >> > >> anita@anitas-computer:~$ sudo wvdial > >> > >> --> WvDial: Internet dialer version 1.56 > >> --> Cannot get information for serial port. > >> --> Initializing modem. > >> --> Sending: ATZ > >> ATZ > >> OK > >> --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > >> ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > >> OK > >> --> Modem initialized. > >> --> Sending: ATDT7054579564 > >> --> Waiting for carrier. > >> ATDT7054579564 > >> NO CARRIER > >> ERROR > >> > >> So then I tried this: > >> > >> [Dialer Defaults] > >> Init1 = ATZ > >> Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > >> Modem Type = Analog Modem > >> Baud = 460800 > >> Modem = /dev/ttySL0 > >> ISDN = 0 > >> Phone = 7054579564 > >> Password = XXXXXXXX > >> Username = XXXXXXXX@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx #this > >> information I obtained by logging into irc and evaluating my personal > >> information. Thought I would give it a try. > >> Carrier Check = no > >> > >> And I got this: > >> > >> anita@anitas-computer:~$ sudo wvdial > >> > >> --> WvDial: Internet dialer version 1.56 > >> --> Cannot get information for serial port. > >> --> Initializing modem. > >> --> Sending: ATZ > >> ATZ > >> OK > >> --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > >> ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > >> OK > >> --> Modem initialized. > >> --> Sending: ATDT7054579564 > >> --> Waiting for carrier. > >> ATDT7054579564 > >> NO CARRIER > >> ERROR > >> > >> What should I try next? > >> > >> Thank you, > >> Anita. > >> > >> > >> > >> > >> > >> Marvin Stodolsky wrote: > >> > Anita, > >> > Add a line to /etc/wvdial.conf > >> > Carrier Check = no > >> > and then retest as before. This line is necessary, because /dev/pts/N > >> > ports do not yet have "sound hearing" capability and hence cannot hear > >> > the Carrier signal. > >> > > >> > MarvS > >> > > >> > On Thu, Mar 6, 2008 at 4:33 PM, Anita Kuno <ay.kuno@xxxxxxxxx> wrote: > >> > > >> >> Thank you, Jacques, I did figure out that my problem from my last post > >> >> was that I had not configured the file by calling wvdialconf. Thank you > >> >> for your clarity. > >> >> > >> >> So after running wvdialconf, I configured the file as follows: > >> >> > >> >> [Dialer Defaults] > >> >> Init1 = ATZ > >> >> Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > >> >> Modem Type = Analog Modem > >> >> Baud = 460800 > >> >> > >> >> Modem = /dev/ttySL0 > >> >> ISDN = 0 > >> >> Phone = 7054579564 > >> >> Password = XXXXXXXX #hidden for the purpose of this email > >> >> Username = XXXXXXXX #hidden for the purpose of this email > >> >> > >> >> And ran sudo wvdial: > >> >> $ sudo wvdial > >> >> > >> >> --> WvDial: Internet dialer version 1.56 > >> >> --> Cannot get information for serial port. > >> >> --> Initializing modem. > >> >> --> Sending: ATZ > >> >> ATZ > >> >> OK > >> >> --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > >> >> > >> >> ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > >> >> OK > >> >> --> Modem initialized. > >> >> --> Sending: ATDT7054579564 > >> >> --> Waiting for carrier. > >> >> ATDT7054579564 > >> >> NO CARRIER > >> >> ERROR > >> >> --> No Carrier! Trying again. > >> >> --> Sending: ATDT7054579564 > >> >> --> Waiting for carrier. > >> >> ATDT7054579564 > >> >> NO CARRIER > >> >> > >> >> So, NO CARRIER. What is it looking for and how do I give it what it wants? > >> >> > >> >> > >> >> Thanks, > >> >> Anita. > >> >> > >> >> > >> >> Jacques Goldberg wrote: > >> >> > Again > >> >> > > >> >> > 1-In one window, sudo slmodemd etc... > >> >> > 2-In an other window, sudo wvdialconf /etc/wvdial.conf > >> >> > Instead, you did sudo wvdial /etc/wvdial.conf > >> >> > but wvdialconf and wvdial are NOT the same thing. These are two > >> >> > DIFFERENT commands. One configures the modem once for all, the other, > >> >> > wvdial , makes the connection > >> >> > > >> >> > You must run wvdialconf as shown, at least ONCE, while slmodemd IS > >> >> > running > >> >> > wvdialconf will find your modem > >> >> > Edit the file /etc/wvdial.conf (username, password, phone . Remove > >> >> > leading ; and < > containers and replace parameter in container by > >> >> > value given to you by your ISP ) > >> >> > > >> >> > Only NOW can you try, as many times as you like sudo wvdial > >> >> > and note, NOT sudo wvdial /etc/wvdial.conf , just sudo wvdial > >> >> > wvdial knows that it has to use /etc/wvdial.conf > >> >> > > >> >> > And just to make sure: slmodemd MUST also be running while you try > >> >> > wvdial > >> >> > >> >> > >> >> > >> >> > Jacques > >> >> > > >> >> > Anita Kuno wrote: > >> >> >> Thank you, Jacques, you are entirely correct. I do not understand > >> >> >> the procedure. > >> >> >> > >> >> >> However, when I sent > >> >> >> Results from second terminal with first terminal running slmodemd: > >> >> >> that was my way of saying that I had done the first step as you > >> >> >> outlined: > >> >> >> 1-In one window, you start slmodemd and DO NOT STOP IT > >> >> >> > >> >> >> And when I also submitted: > >> >> >> anita@anitas-computer:~$ sudo wvdial /etc/wvdial.conf > >> >> >> Password: > >> >> >> --> WvDial: Internet dialer version 1.56 > >> >> >> --> Warning: section [Dialer /etc/wvdial.conf] does not exist in > >> >> >> wvdial.conf. > >> >> >> --> Cannot open /dev/modem: No such file or directory > >> >> >> --> Cannot open /dev/modem: No such file or directory > >> >> >> --> Cannot open /dev/modem: No such file or directory > >> >> >> > >> >> >> That was my way of demonstrating that I had: > >> >> >> 2-In an other window you start > >> >> >> sudo wvdialconf /etc/wvdial./.conf > >> >> >> > >> >> >> And I was hoping for: > >> >> >> which should find your modem > >> >> >> > >> >> >> And perhaps I mis-interpreted the result, but when I read: > >> >> >> --> Warning: section [Dialer /etc/wvdial.conf] does not exist in > >> >> >> wvdial.conf. > >> >> >> --> Cannot open /dev/modem: No such file or directory > >> >> >> --> Cannot open /dev/modem: No such file or directory > >> >> >> --> Cannot open /dev/modem: No such file or directory > >> >> >> I took that to mean that it couldn't find the modem. > >> >> >> > >> >> >> So I am wondering how to find the modem. > >> >> >> > >> >> >> Thanks, > >> >> >> Anita. > >> >> >> > >> >> >> > >> >> >> > >> >> >> > >> >> >> Jacques Goldberg wrote: > >> >> >>> I believe that you do not understand the procedure > >> >> >>> > >> >> >>> 1-In one window, you start slmodemd and DO NOT STOP IT > >> >> >>> 2-In an other window you start > >> >> >>> sudo wvdialconf /etc/wvdial./.conf > >> >> >>> which should find your modem > >> >> >>> When wvdialconf exits and has found a modem, you EDIT > >> >> >>> the file /etc/wvdial.conf to set username, password, phone > >> >> >>> as in > >> >> >>> username = tartempion > >> >> >>> phone = 0123456788 > >> >> >>> password = sunday_times > >> >> >>> After editing, you start wvdial as > >> >> >>> sudo wvdial > >> >> >>> and you do NOT stop wvdial until you want to close the phone call. > >> >> >>> You cannot use these two windows for anything else until you have > >> >> >>> ended wvdial and slmodemd > >> >> >>> > >> >> >>> Jacques > >> >> >>> > >> >> >>> Anita Kuno wrote: > >> >> >>>> Thank you Marvin and Antonio, > >> >> >>>> > >> >> >>>> Results from second terminal with first terminal running slmodemd: > >> >> >>>> > >> >> >>>> anita@anitas-computer:~$ sudo wvdial /etc/wvdial.conf > >> >> >>>> Password: > >> >> >>>> --> WvDial: Internet dialer version 1.56 > >> >> >>>> --> Warning: section [Dialer /etc/wvdial.conf] does not exist in > >> >> >>>> wvdial.conf. > >> >> >>>> --> Cannot open /dev/modem: No such file or directory > >> >> >>>> --> Cannot open /dev/modem: No such file or directory > >> >> >>>> --> Cannot open /dev/modem: No such file or directory > >> >> >>>> anita@anitas-computer:~$ > >> >> >>>> > >> >> >>>> > >> >> >>>> Marvin Stodolsky wrote: > >> >> >>>>> Anita, > >> >> >>>>> > >> >> >>>>> Just to clarify on Antonio's terse comment. > >> >> >>>>> After the successful: > >> >> >>>>> $ sudo slmodemd -c CANADA --alsa hw:0,6 > >> >> >>>>> leave slmodemd running. > >> >> >>>>> Open a 2nd console or new TAB on the same one and run the > >> >> >>>>> $ sudo wvdialconf /etc/wvdial.conf > >> >> >>>>> If this step succeeds: > >> >> >>>>> $ sudo gedit /etc/wvdial.conf > >> >> >>>>> and edit to a format like that below. > >> >> >>>>> > >> >> >>>>> Afterward with slmodemd still running, try a dialout with: > >> >> >>>>> $ sudo wvdial > >> >> >>>>> > >> >> >>>>> Please report back to the List, not to me directly: > >> >> >>>>> > >> >> >>>>> MarvS > >> >> >>>>> ----------------- > >> >> >>>>> [Dialer Defaults] > >> >> >>>>> Init1 = ATZ > >> >> >>>>> Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > >> >> >>>>> Modem Type = Analog Modem > >> >> >>>>> Baud = 460800 > >> >> >>>>> New PPPD = yes > >> >> >>>>> Modem = /dev/ttySL0 > >> >> >>>>> ISDN = 0 > >> >> >>>>> Password = YourPassword > >> >> >>>>> Username = LoginName@xxxxxxxxxxxxxxxx > >> >> >>>>> Phone = 3015560020 > >> >> >>>>> # needed for usage with /dev/pts/N ports: > >> >> >>>>> Carrier Check = no > >> >> >>>>> > >> >> >>>>> > >> >> >>>>> > >> >> >>>>> > >> >> >>>>> On Wed, Mar 5, 2008 at 7:38 PM, Antonio Olivares > >> >> >>>>> <olivares14031@xxxxxxxxx> wrote: > >> >> >>>>> > >> >> >>>>>> When you did this > >> >> >>>>>> > >> >> >>>>>> > >> >> >>>>>> $ sudo slmodemd -c CANADA --alsa hw:0,6 > >> >> >>>>>> => SmartLink Soft Modem: version 2.9.11 Feb 17 2008 09:31:10 > >> >> >>>>>> => symbolic link `/dev/ttySL0' -> `/dev/pts/1' created. > >> >> >>>>>> => modem `hw:0,6' created. TTY is `/dev/pts/1' > >> >> >>>>>> =>Use `/dev/ttySL0' as modem device, Ctrl+C for termination. > >> >> >>>>>> > >> >> >>>>>> Did you CTRL+C to do sudo wvdialconf /etc/wvdial.conf ? > >> >> >>>>>> > >> >> >>>>>> open up another terminal or session and then type > >> >> >>>>>> > >> >> >>>>>> > >> >> >>>>>> $ sudo wvdialconf /etc/wvdial.conf > >> >> >>>>>> > >> >> >>>>>> That should find your modem, and get you setup. Please report > >> >> >>>>>> back if > >> >> >>>>>> you have trouble/questions. > >> >> >>>>>> > >> >> >>>>>> Regards, > >> >> >>>>>> > >> >> >>>>>> Antonio > >> >> >>>>>> > >> >> >>>>>> > >> >> >>>>>> > >> >> >>>>>> On 3/5/08, Anita Kuno <ay.kuno@xxxxxxxxx> wrote: > >> >> >>>>>> > I have unpacked SLMODEMD: > >> >> >>>>>> > $ tar -zxvf ./SLMODEMD.gcc4.1.tar.gz > >> >> >>>>>> > > >> >> >>>>>> > And I believe this makes SLMODEMD an executable file: > >> >> >>>>>> > $ chmod +x slmodemd > >> >> >>>>>> > $ sudo cp slmodemd /usr/sbin > >> >> >>>>>> > > >> >> >>>>>> > And I think this verifies the location: > >> >> >>>>>> > $ find /usr -name slmodemd > >> >> >>>>>> > => /usr/sbin/slmodemd > >> >> >>>>>> > > >> >> >>>>>> > So then I installed SLMODEMD: > >> >> >>>>>> > $ sudo slmodemd -c CANADA --alsa hw:0,6 > >> >> >>>>>> > => SmartLink Soft Modem: version 2.9.11 Feb 17 2008 09:31:10 > >> >> >>>>>> > => symbolic link `/dev/ttySL0' -> `/dev/pts/1' created. > >> >> >>>>>> > => modem `hw:0,6' created. TTY is `/dev/pts/1' > >> >> >>>>>> > =>Use `/dev/ttySL0' as modem device, Ctrl+C for termination. > >> >> >>>>>> > > >> >> >>>>>> > So then I worked on wvdial. > >> >> >>>>>> > $ which wvdial > >> >> >>>>>> > => /usr/bin/wvdial > >> >> >>>>>> > $ sudo wvdialconf /etc/wvdial.conf > >> >> >>>>>> > =>Editing `/etc/wvdial.conf'. > >> >> >>>>>> > => Scanning your serial ports for a modem. > >> >> >>>>>> > => Modem Port Scan<*1>: S0 S1 S2 S3 > >> >> >>>>>> > => Sorry, no modem was detected! Is it in use by another > >> >> >>>>>> program? > >> >> >>>>>> > => Did you configure it properly with setserial? > >> >> >>>>>> > => Please read the FAQ at http://open.nit.ca/wiki/?WvDial > >> >> >>>>>> > => If you still have problems, send mail to > >> >> >>>>>> <wvdial-list@xxxxxxxxxxxx>. > >> >> >>>>>> > > >> >> >>>>>> > I have tried the url to find the FAQ, can't find it. > >> >> >>>>>> > And I have emailed them to ask for the FAQ url, no response. > >> >> >>>>>> > > >> >> >>>>>> > So I have evaluated the sound card: > >> >> >>>>>> > $ cat /proc/asound/cards > >> >> >>>>>> > => 0 [Intel ]: HDA-Intel - HDA Intel > >> >> >>>>>> > => HDA Intel at 0xd8240000 irq 21 > >> >> >>>>>> > > >> >> >>>>>> > And run uname: > >> >> >>>>>> > $ uname -a > >> >> >>>>>> > Linux anitas-computer 2.6.20-15-generic #2 SMP Sun Apr 15 > >> >> >>>>>> 07:36:31 UTC > >> >> >>>>>> > 2007 i686 GNU/Linux > >> >> >>>>>> > > >> >> >>>>>> > And confirmed module-init-tools: > >> >> >>>>>> > $ dpkg -s module-init-tools > >> >> >>>>>> > => Package: module-init-tools > >> >> >>>>>> > => Status: install ok installed > >> >> >>>>>> > > >> >> >>>>>> > What is my next step? > >> >> >>>>>> > > >> >> >>>>>> > Thank you, > >> >> >>>>>> > Anita. > >> >> >>>>>> > > >> >> >>>>>> > > >> >> >>>>>> > > >> >> >>>>>> > > >> >> >>>>>> > > >> >> >>>>>> > >> >> >>>>>> > >> >> >>>>> > >> >> >>>>> > >> >> >>>> > >> >> >>> > >> >> >> > >> >> > > >> >> > >> >> > >> >> > >> > > >> > > >> > >> > >> > > > > > > > anita@anitas-computer:~$ sudo slmodemd -c CANADA -a --debug=2 --log hw:0,6 > Password: > SmartLink Soft Modem: version 2.9.11 Feb 17 2008 09:31:10 > <102.811403> SmartLink Soft Modem: version 2.9.11 Feb 17 2008 09:31:10 > <102.811493> hw:0,6: startup modem... > <102.811607> hw:0,6: update termios... > symbolic link `/dev/ttySL0' -> `/dev/pts/2' created. > modem `hw:0,6' created. TTY is `/dev/pts/2' > <102.812335> open file: /var/lib/slmodem/data.hw:0,6... > <102.812400> cannot open '/var/lib/slmodem/data.hw:0,6': No such file or directory > <102.821020> main: rt applyed: SCHED_FIFO, pri 99 > Use `/dev/ttySL0' as modem device, Ctrl+C for termination. > <123.805297> main: termios changed. > <123.805359> hw:0,6: update termios... > <123.899945> main: termios changed. > <123.899990> hw:0,6: update termios... > <123.999911> hw:0,6: run cmd: ATZ > <123.999954> hw:0,6: modem reset... > <123.999974> hw:0,6: modem set state: 1 --> 1... > <123.999997> hw:0,6: modem set mode: -> 0... > <124.000017> hw:0,6: modem report result: 0 (OK) > <124.100007> hw:0,6: run cmd: ATQ0V1E1S0=0&C1&D2+FCLASS=0 > <124.100058> hw:0,6: modem set mode: -> 0... > <124.100079> hw:0,6: modem report result: 0 (OK) > <124.200095> hw:0,6: run cmd: ATDT7054579564 > <124.200156> hw:0,6: modem dial: T7054579564... > <124.200177> hw:0,6: modem_dial_start... > <124.200985> hw:0,6: modem_start.. > <124.201010> hw:0,6: modem set state: 1 --> 2... > <124.201045> hw:0,6: new state: DP_ESTAB > <124.201069> main: alsa_ioctl: cmd 8, arg 3... > <124.201089> hw:0,6: modem set hook: 0 --> 1... > <124.201119> main: alsa_ioctl: cmd 2, arg 1... > <124.211866> main: alsa_ioctl: cmd 11, arg 0... > <124.211950> main: alsa_ioctl: cmd 4, arg 2580... > <124.211976> main: alsa_ioctl: cmd 7, arg 30... > <124.211995> main: alsa_start... > error: cannot setup hw params for playback: Invalid argument > <124.212186> err: hw:0,6: modem start = -22: cannot start device. > <124.212210> hw:0,6: modem_stop.. > <124.212227> hw:0,6: modem set hook: 1 --> 0... > <124.212246> main: alsa_ioctl: cmd 2, arg 0... > <124.219868> main: alsa_ioctl: cmd 8, arg 0... > <124.220007> hw:0,6: modem set state: 2 --> 1... > <124.220030> hw:0,6: new state: MODEM_IDLE > <124.220053> hw:0,6: modem report result: 3 (NO CARRIER) > <124.220081> hw:0,6: modem report result: 4 (ERROR) > <124.520058> hw:0,6: run cmd: ATDT7054579564 > <124.520122> hw:0,6: modem dial: T7054579564... > <124.520143> hw:0,6: modem_dial_start... > <124.520965> hw:0,6: modem_start.. > <124.520988> hw:0,6: modem set state: 1 --> 2... > <124.521023> hw:0,6: new state: DP_ESTAB > <124.521056> main: alsa_ioctl: cmd 8, arg 3... > <124.521089> hw:0,6: modem set hook: 0 --> 1... > <124.521121> main: alsa_ioctl: cmd 2, arg 1... > <124.531858> main: alsa_ioctl: cmd 11, arg 0... > <124.531945> main: alsa_ioctl: cmd 4, arg 2580... > <124.531974> main: alsa_ioctl: cmd 7, arg 30... > <124.531993> main: alsa_start... > error: cannot setup hw params for playback: Invalid argument > <124.539942> err: hw:0,6: modem start = -22: cannot start device. > <124.539978> hw:0,6: modem_stop.. > <124.539998> hw:0,6: modem set hook: 1 --> 0... > <124.540017> main: alsa_ioctl: cmd 2, arg 0... > <124.547855> main: alsa_ioctl: cmd 8, arg 0... > <124.547978> hw:0,6: modem set state: 2 --> 1... > <124.547997> hw:0,6: new state: MODEM_IDLE > <124.548019> hw:0,6: modem report result: 3 (NO CARRIER) > <124.548048> hw:0,6: modem report result: 4 (ERROR) > <124.848056> hw:0,6: run cmd: ATDT7054579564 > <124.848117> hw:0,6: modem dial: T7054579564... > <124.848138> hw:0,6: modem_dial_start... > <124.848943> hw:0,6: modem_start.. > <124.848967> hw:0,6: modem set state: 1 --> 2... > <124.849002> hw:0,6: new state: DP_ESTAB > <124.849035> main: alsa_ioctl: cmd 8, arg 3... > <124.849067> hw:0,6: modem set hook: 0 --> 1... > <124.849099> main: alsa_ioctl: cmd 2, arg 1... > <124.859854> main: alsa_ioctl: cmd 11, arg 0... > <124.859941> main: alsa_ioctl: cmd 4, arg 2580... > <124.859965> main: alsa_ioctl: cmd 7, arg 30... > <124.859984> main: alsa_start... > error: cannot setup hw params for playback: Invalid argument > <124.867934> err: hw:0,6: modem start = -22: cannot start device. > <124.867969> hw:0,6: modem_stop.. > <124.867988> hw:0,6: modem set hook: 1 --> 0... > <124.868007> main: alsa_ioctl: cmd 2, arg 0... > <124.875855> main: alsa_ioctl: cmd 8, arg 0... > <124.875980> hw:0,6: modem set state: 2 --> 1... > <124.875999> hw:0,6: new state: MODEM_IDLE > <124.876017> hw:0,6: modem report result: 3 (NO CARRIER) > <124.876043> hw:0,6: modem report result: 4 (ERROR) > <125.176053> hw:0,6: run cmd: ATDT7054579564 > <125.176123> hw:0,6: modem dial: T7054579564... > <125.176144> hw:0,6: modem_dial_start... > <125.176945> hw:0,6: modem_start.. > <125.176969> hw:0,6: modem set state: 1 --> 2... > <125.177003> hw:0,6: new state: DP_ESTAB > <125.177037> main: alsa_ioctl: cmd 8, arg 3... > <125.177068> hw:0,6: modem set hook: 0 --> 1... > <125.177101> main: alsa_ioctl: cmd 2, arg 1... > <125.187850> main: alsa_ioctl: cmd 11, arg 0... > <125.187935> main: alsa_ioctl: cmd 4, arg 2580... > <125.187961> main: alsa_ioctl: cmd 7, arg 30... > <125.187980> main: alsa_start... > error: cannot setup hw params for playback: Invalid argument > <125.195938> err: hw:0,6: modem start = -22: cannot start device. > <125.195974> hw:0,6: modem_stop.. > <125.195993> hw:0,6: modem set hook: 1 --> 0... > <125.196013> main: alsa_ioctl: cmd 2, arg 0... > <125.203844> main: alsa_ioctl: cmd 8, arg 0... > <125.203967> hw:0,6: modem set state: 2 --> 1... > <125.203986> hw:0,6: new state: MODEM_IDLE > <125.204005> hw:0,6: modem report result: 3 (NO CARRIER) > <125.204031> hw:0,6: modem report result: 4 (ERROR) > <125.504051> hw:0,6: run cmd: ATDT7054579564 > <125.504122> hw:0,6: modem dial: T7054579564... > <125.504144> hw:0,6: modem_dial_start... > <125.504949> hw:0,6: modem_start.. > <125.504973> hw:0,6: modem set state: 1 --> 2... > <125.505007> hw:0,6: new state: DP_ESTAB > <125.505041> main: alsa_ioctl: cmd 8, arg 3... > <125.505073> hw:0,6: modem set hook: 0 --> 1... > <125.505106> main: alsa_ioctl: cmd 2, arg 1... > <125.515841> main: alsa_ioctl: cmd 11, arg 0... > <125.515928> main: alsa_ioctl: cmd 4, arg 2580... > <125.515953> main: alsa_ioctl: cmd 7, arg 30... > <125.515972> main: alsa_start... > error: cannot setup hw params for playback: Invalid argument > <125.523920> err: hw:0,6: modem start = -22: cannot start device. > <125.523959> hw:0,6: modem_stop.. > <125.523978> hw:0,6: modem set hook: 1 --> 0... > <125.523997> main: alsa_ioctl: cmd 2, arg 0... > <125.531846> main: alsa_ioctl: cmd 8, arg 0... > <125.531970> hw:0,6: modem set state: 2 --> 1... > <125.531990> hw:0,6: new state: MODEM_IDLE > <125.532008> hw:0,6: modem report result: 3 (NO CARRIER) > <125.532034> hw:0,6: modem report result: 4 (ERROR) > <125.832041> hw:0,6: run cmd: ATDT7054579564 > <125.832109> hw:0,6: modem dial: T7054579564... > <125.832130> hw:0,6: modem_dial_start... > <125.832932> hw:0,6: modem_start.. > <125.832963> hw:0,6: modem set state: 1 --> 2... > <125.832997> hw:0,6: new state: DP_ESTAB > <125.833021> main: alsa_ioctl: cmd 8, arg 3... > <125.833041> hw:0,6: modem set hook: 0 --> 1... > <125.833072> main: alsa_ioctl: cmd 2, arg 1... > <125.843834> main: alsa_ioctl: cmd 11, arg 0... > <125.843925> main: alsa_ioctl: cmd 4, arg 2580... > <125.843949> main: alsa_ioctl: cmd 7, arg 30... > <125.843968> main: alsa_start... > error: cannot setup hw params for playback: Invalid argument > <125.851921> err: hw:0,6: modem start = -22: cannot start device. > <125.851957> hw:0,6: modem_stop.. > <125.851976> hw:0,6: modem set hook: 1 --> 0... > <125.851995> main: alsa_ioctl: cmd 2, arg 0... > <125.859832> main: alsa_ioctl: cmd 8, arg 0... > <125.859958> hw:0,6: modem set state: 2 --> 1... > <125.859978> hw:0,6: new state: MODEM_IDLE > <125.859996> hw:0,6: modem report result: 3 (NO CARRIER) > <125.860023> hw:0,6: modem report result: 4 (ERROR) > <126.160045> hw:0,6: run cmd: ATDT7054579564 > <126.160121> hw:0,6: modem dial: T7054579564... > <126.160141> hw:0,6: modem_dial_start... > <126.160954> hw:0,6: modem_start.. > <126.160978> hw:0,6: modem set state: 1 --> 2... > <126.161012> hw:0,6: new state: DP_ESTAB > <126.161036> main: alsa_ioctl: cmd 8, arg 3... > <126.161056> hw:0,6: modem set hook: 0 --> 1... > <126.161088> main: alsa_ioctl: cmd 2, arg 1... > <126.171827> main: alsa_ioctl: cmd 11, arg 0... > <126.171919> main: alsa_ioctl: cmd 4, arg 2580... > <126.171944> main: alsa_ioctl: cmd 7, arg 30... > <126.171964> main: alsa_start... > error: cannot setup hw params for playback: Invalid argument > <126.179911> err: hw:0,6: modem start = -22: cannot start device. > <126.179947> hw:0,6: modem_stop.. > <126.179967> hw:0,6: modem set hook: 1 --> 0... > <126.179986> main: alsa_ioctl: cmd 2, arg 0... > <126.187831> main: alsa_ioctl: cmd 8, arg 0... > <126.187956> hw:0,6: modem set state: 2 --> 1... > <126.187975> hw:0,6: new state: MODEM_IDLE > <126.187993> hw:0,6: modem report result: 3 (NO CARRIER) > <126.188019> hw:0,6: modem report result: 4 (ERROR) > <126.488026> hw:0,6: run cmd: ATDT7054579564 > <126.488096> hw:0,6: modem dial: T7054579564... > <126.488117> hw:0,6: modem_dial_start... > <126.488919> hw:0,6: modem_start.. > <126.488949> hw:0,6: modem set state: 1 --> 2... > <126.488971> hw:0,6: new state: DP_ESTAB > <126.488992> main: alsa_ioctl: cmd 8, arg 3... > <126.489013> hw:0,6: modem set hook: 0 --> 1... > <126.489044> main: alsa_ioctl: cmd 2, arg 1... > <126.499829> main: alsa_ioctl: cmd 11, arg 0... > <126.499927> main: alsa_ioctl: cmd 4, arg 2580... > <126.499953> main: alsa_ioctl: cmd 7, arg 30... > <126.499972> main: alsa_start... > error: cannot setup hw params for playback: Invalid argument > <126.507907> err: hw:0,6: modem start = -22: cannot start device. > <126.507944> hw:0,6: modem_stop.. > <126.507963> hw:0,6: modem set hook: 1 --> 0... > <126.507983> main: alsa_ioctl: cmd 2, arg 0... > <126.515817> main: alsa_ioctl: cmd 8, arg 0... > <126.515965> hw:0,6: modem set state: 2 --> 1... > <126.515986> hw:0,6: new state: MODEM_IDLE > <126.516004> hw:0,6: modem report result: 3 (NO CARRIER) > <126.516030> hw:0,6: modem report result: 4 (ERROR) > <126.728412> main: termios changed. > <126.728456> hw:0,6: update termios... > <126.728479> main: pty closed. > > > > >
