Alex, A few issues to work through1) /proc/asound/card0/codec#1 has the audio function info,Please send the output of $ cat /proc/asound/card0/codec#0as this will likely provide the softmodem chip info.More broadly, please$ cp -a /proc/asound APT$ tar cfz APT.tgz APT/and send only to me the APT.tgz to analyze. 2) PCI: Setting latency timer of device 0000:00:1b.0 to 64hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...There may not yet be support for ALC883 in your ALSA version.What is your output of:$ aplay --version 3) hda-intel: invalid format_val, rate=9600, ch=1, format=2hda-intel: invalid format_val, rate=9600, ch=1, format=2--------This is an ALSA bug, now supposedly corrected (excerpting from ALSAmaintainer report:========= tiwai - 05-18-07 17:12----------------------------------------------------------------------The 9600HZ support was fixed again in the recent version (2.6.22-rc1).=========So upgrading your kernel might help. Please report back. MarvS On 6/18/07, Alexandre Penasso Teixeira <alexandre@xxxxxxxxxxxxxxxxxxx> wrote:> Marvin,>> Sorry for my don't attention. I change my .wvdial.conf and try with> country, but don't work.>> I get debug log with:> slmodemd -c BRAZIL --alsa hw:0,6 -d 3 2>slmodemd.log-*>> I attach this logs for you, in dmesg have any info:> hda-intel: invalid format_val, rate=9600, ch=1, format=2> hda-intel: invalid format_val, rate=9600, ch=1, format=2> ...>> I don't know if logs can help, but hope.>> Thank you...>> []'s> Alexandre>>> Em Seg, 2007-06-18 às 14:01 -0400, Marvin Stodolsky escreveu:> > Alex> >> > RE:> > card 0: Intel [HDA Intel], device 6: Si3054 Modem [Si3054 Modem]> > Subdevices: 1/1> > Subdevice #0: subdevice #0> > ==> # slmodemd --alsa hw:0> >> > The proper setup COMMAND is:> > # slmodemd --alsa hw:0,6> > since the modem is subsdevice 6 on card 0> >> > Follow Antonio's guidance and use wvdial,> > except don't use> > Stupid Mode = yes> > unless essential.> >> > You may also have to use a country setting in the slmodemd command> > # slmodemd -c YOUR_COUNTRY --alsa hw:0,6> > with your country in the ouput of> > $ slmodemd --countrylist> >> > MarvS> >> >> >> > On 6/18/07, Antonio Olivares <olivares14031@xxxxxxxxx> wrote:> > >> > >> > > ----- Original Message ----> > > From: Alexandre Penasso Teixeira <alexandre@xxxxxxxxxxxxxxxxxxx>> > > To: Linmodems <discuss@xxxxxxxxxxxxx>> > > Sent: Monday, June 18, 2007 10:13:30 AM> > > Subject: Modem Motorola HDA> > >> > > Hi developers,> > >> > > I have one modem sm56-hda, and build the new driver> > > slmodem-2.9.11-2007050 and ungrab-winmodem-20070505 alsa on.> > > make SUPPORT_ALSA=1> > >> > > I build ok, but after load the slmodemd I don't dialing... look it.> > >> > > ==> # aplay -l> > > **** List of PLAYBACK Hardware Devices ****> > > card 0: Intel [HDA Intel], device 0: ALC883 Analog [ALC883 Analog]> > > Subdevices: 0/1> > > Subdevice #0: subdevice #0> > > card 0: Intel [HDA Intel], device 1: ALC883 Digital [ALC883 Digital]> > > Subdevices: 1/1> > > Subdevice #0: subdevice #0> > > card 0: Intel [HDA Intel], device 6: Si3054 Modem [Si3054 Modem]> > > Subdevices: 1/1> > > Subdevice #0: subdevice #0> > >> > > ==> # slmodemd --alsa hw:0> > > SmartLink Soft Modem: version 2.9.11 Jun 18 2007 12:46:42> > > symbolic link `/dev/ttySL0' -> `/dev/pts/1' created.> > > modem `hw:0' created. TTY is `/dev/pts/1'> > > Use `/dev/ttySL0' as modem device, Ctrl+C for termination.> > >> > > ==> # minicom> > > Welcome to minicom 2.1> > >> > > OP+�+�ES: History Buffer, F-key Macros, Search History Buffer, I18n> > > Compilado em Nov 4 2005, 18:10:30.> > >> > > Pressione CTRL-A Z para ajuda sobre teclas especiais> > >> > > AT S7=45 S0=0 L1 V1 X4 &c1 E1 Q0> > > OK> > > atx3dt 225> > > NO CARRIER> > > ERROR> > >> > >> > > I have on phone-line running ok... with other notebook dialing ok... Are> > > you have suggestions ?> > >> > > []'s> > > Alexandre> > >> > >> > > Could you try it out with wvdial?> > > Add option Carrier check = no> > > Your wvdial.conf file should look something like> > >> > > [olivares@localhost ~]$ cat /etc/wvdial.conf> > >> > > [Dialer Defaults]> > > Modem = /dev/ttySL0> > > Baud = 460800> > > Init1 = ATZ> > > #Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +MS=90> > > Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0> > > ISDN = 0> > > Modem Type = Analog Modem> > > Carrier Check = no> > > Stupid Mode = yes> > > Auto DNS = yes> > > Phone = your_phone_number> > > Username = your_username> > > Password = your_password> > >> > > Hope this helps,> > >> > > Antonio> > >> > >> > >> > >> > >> > >> > > ____________________________________________________________________________________> > > Need a vacation? Get great deals> > > to amazing places on Yahoo! Travel.> > > http://travel.yahoo.com/> > >>>
