Ah, I dumped them with Windows new line characters. Here is a new log binary dump. I moved to the newest TGL GuC firmware from linux-firmware repo. środa, 21 lutego 2024 12:16 AM, John Harrison <john.c.harrison@xxxxxxxxx> napisał(a): > > > Hello, > > Something is very corrupted with that GuC log. The log consists of a > header page and then a stream of log entry structures. The structure is > supposed to be 20 bytes long and starts with a four byte time stamp. But > I am seeing what is conceivably a 32bit timestamp appearing at 21 byte > increments through the log. Even more curiously, the time stamp seems to > have an 0x0D, 0x0A after it. Are you doing any printf type operation in > order to write the log out from memory to disk? > > INTEL_GUC_LOAD_STATUS_INIT_DATA_INVALID means that the GuC did not like > the initialisation data passed in. Most likely, something in the ADS > structure is not valid. If you try with the latest GuC version, that > might give you more information as to what is the incorrect. More status > codes have been added since 70.1.1. > > John. > > > On 2/20/2024 05:03, maksym@xxxxxxxxxxx wrote: > > > Hi, > > > > Please see GuC log attached to this email. > > > > Log size is "PAGE_SIZE+Debug Log(64KB) + Crash Log (8KB) + Capture Log (1M)" > > > > Can anybody from Intel decode this log buffer? Thanks. > > > > What am I doing wrong? > > > > Maksym > > > > poniedziałek, 19 lutego 2024 09:44, maksym@xxxxxxxxxxx maksym@xxxxxxxxxxx napisał(a): > > > > > Hi, > > > > > > I fixed one issue in my driver. Log address was set incorrectly. > > > > > > Right now, after GuC uploading, GUC_STATUS changed. > > > Right now, intel_guc_load_status is INTEL_GUC_LOAD_STATUS_INIT_DATA_INVALID = 0x71. > > > > > > What does it mean? > > > Could you please help me with this? > > > > > > Thanks, > > > Maksym > > > > > > piątek, 9 lutego 2024 08:42, natur.produkt@xxxxx natur.produkt@xxxxx napisał(a): > > > > > > > Hello, > > > > > > > > Please see my comments below. > > > > > > > > piątek, 9 lutego 2024 2:45 AM, John Harrison john.c.harrison@xxxxxxxxx napisał(a): > > > > > > > > > Hello, > > > > > > > > > > What platform is this on? And which GuC firmware version are you using? > > > > > It's TGL. I'm using tgl_guc_70.1.1.bin firmware blob. > > > > > > > > > One thing you made need to do is force maximum GT frequency during GuC > > > > > load. That is something the i915 driver does. If the system decides the > > > > > GPU is idle and drops the frequency to minimum then it can take multiple > > > > > seconds for the GuC initialisation to complete. > > > > > Thanks for the hint. I'm not doing that at all in my code. How am I supposed to do this? Is there a specific register for that? > > > > > > > > > Did the status change at all during that second of waiting? Or was it > > > > > still reading LAPIC_DONE? > > > > > It's always LAPIC_DONE. > > > > > > > > > For ADS documentation, I'm afraid that the best we currently have > > > > > publicly available is the i915 driver code. If you are not intending to > > > > > use GuC submission then most of the ADS can be ignored. > > > > > Ok, that great. Which part of ADS is must-have then? > > > > > > > > > If you can share the GuC log, that might provide some clues as to what > > > > > is happening. For just logging the boot process, you shouldn't need to > > > > > allocate a large log. The default size of i915 for release builds is > > > > > 64KB. That should be plenty. > > > > > I'll collect GuC log as soon as possible. Is it something that can be understood without a knowledge of GuC internals? Or is it simply hex dumps? > > > > > > > > > John. > > > > > > > > > > On 2/6/2024 23:59, natur.produkt@xxxxx wrote: > > > > > > > > > > > Hi, > > > > > > > > > > > > I'm currently implementing GuC/HuC firmware support in one Safety Critical OS. > > > > > > I'm following i915 code and I implemented all paths (I don't want GuC submission or SLPC features). I need GuC to authenticate HuC firmware blob. > > > > > > > > > > > > I mirrored GuC implementation in my code. > > > > > > > > > > > > After GuC DMA transfer succeeds, I'm reading GUC_STATUS register. > > > > > > HW returns INTEL_BOOTROM_STATUS_JUMP_PASSED as bootrom status and INTEL_GUC_LOAD_STATUS_LAPIC_DONE as GuC load status. > > > > > > > > > > > > Unfortunately, after one second of waiting, the status didn't get changed to INTEL_GUC_LOAD_STATUS_READY at all. > > > > > > > > > > > > What is a potential issue here? > > > > > > Could you please help me? > > > > > > > > > > > > In addition to this, could you please point out some documentation about GuC's ADS struct? > > > > > > > > > > > > Thanks, > > > > > > Maksym
Attachment:
fullLog.bin
Description: application/macbinary