and where is the duplicated Radius packet ?????????????????????????????? Those two packets are from completely separated calls. ----- Original Message ----- From: "Tusar" <tusarbd@xxxxxxxxx> To: <openh323gk-users@xxxxxxxxxxxxxxxxxxxxx> Sent: Tuesday, January 18, 2005 6:24 PM Subject: Re: Acct-Session-Id Unique or Conf-id Unique ? > Hi, > > Thanks for reply .. But GK and Radius are running at the same server.. > Here is below from radius detail log .. > > Fri Jan 7 18:49:08 2005 > Acct-Status-Type = Stop > NAS-IP-Address = xx.xx.xx.xx > NAS-Identifier = "TestGK" > NAS-Port-Type = Virtual > Service-Type = Login-User > Acct-Session-Id = "41dd827300004eef" > User-Name = "xxxx" > Framed-IP-Address = xx.xx.xx.xx > Acct-Session-Time = 1560 > Calling-Station-Id = "991151" > Called-Station-Id = "880821714504" > H323-conf-id = "h323-conf-id=71374C48 14A43016 3CA10507 1AF6A59" > H323-gw-id = "h323-gw-id=TestGK" > H323-call-origin = "h323-call-origin=proxy" > H323-call-type = "h323-call-type=VoIP" > H323-setup-time = "h323-setup-time=18:22:46.000 BDT Fri Jan 07 2005" > H323-connect-time = "h323-connect-time=18:23:08.000 BDT Fri Jan 07 2005" > H323-disconnect-time = "h323-disconnect-time=18:49:08.000 BDT > Fri Jan 07 2005" > H323-disconnect-cause = "h323-disconnect-cause=0" > H323-remote-address = "h323-remote-address=xxx.xxx.xxx.xxx" > Cisco-AVPair = "h323-ivr-out=h323-call-id:72374C48 14A43016 > 3CA10507 1AF6A59" > Acct-Delay-Time = 0 > Client-IP-Address = 127.0.0.1 > Timestamp = 1105102148 > Request-Authenticator = Verified > > Tue Jan 18 19:49:51 2005 > Acct-Status-Type = Stop > NAS-IP-Address = xx.xx.xx.xx > NAS-Identifier = "TestGK" > NAS-Port-Type = Virtual > Service-Type = Login-User > Acct-Session-Id = "41eaa20f0000753e" > User-Name = "xxxx" > Framed-IP-Address = xx.xx.xx.xx > Acct-Session-Time = 104 > Calling-Station-Id = "991151" > Called-Station-Id = "88028126483" > H323-conf-id = "h323-conf-id=71374C48 14A43016 3CA10507 1AF6A59" > H323-gw-id = "h323-gw-id=TestGK" > H323-call-origin = "h323-call-origin=proxy" > H323-call-type = "h323-call-type=VoIP" > H323-setup-time = "h323-setup-time=19:47:54.000 BDT Tue Jan 18 2005" > H323-connect-time = "h323-connect-time=19:48:07.000 BDT Tue Jan 18 2005" > H323-disconnect-time = "h323-disconnect-time=19:49:51.000 BDT > Tue Jan 18 2005" > H323-disconnect-cause = "h323-disconnect-cause=0" > H323-remote-address = "h323-remote-address=xxx.xxx.xxx.xxx" > Cisco-AVPair = "h323-ivr-out=h323-call-id:72374C48 14A43016 > 3CA10507 1AF6A59" > Acct-Delay-Time = 0 > Client-IP-Address = 127.0.0.1 > Timestamp = 1106056191 > Request-Authenticator = Verified > > > Thanks .. > > Regards. > > ..Tusar.. > > > On Tue, 18 Jan 2005 15:26:25 +0200, Teodor Georgiev > <t.georgiev@xxxxxxxxx> wrote: > > > > > > It might be a duplicate Radius packet for the same call ? > > This causes with Radius servers running at a burden they can't stand > > or a bad IP link. This causes the "Radius client" to resend the AAA packet > > once again. The only difference between such two packets is the Acct-Delay > > field. In such cases your billing application has to deal properly with those > > "delayed" packets. > > > > > > On Tuesday 18 January 2005 14:23, Tusar wrote: > > > Hi, > > > > > > We have integrated Radius with GnuGK and it's running well . > > > But facing some problem with "Acct-Session-Id" , we guessed > > > "Acct-Session-Id" is unique but found sometimes it is getting > > > duplicate , so we are loosing bill . > > > > > > Is "Acct-Session-Id" Unique or "Conf-id" Unique or which field should > > > be unique ? > > > For accounting purpose it is very important for us . > > > > > > Another question is .. > > > > > > Scenerio-1: > > > =========== > > > > > > > Endpoint-2 > > > > > > / > > > EndPoint-1 --> GnuGK --> > > > \ > > > > > > > EndPoint-3 > > > > > > When I am trying to transfer (which call was from Endpoint-1) from > > > Endpoint-2 to EndPoint-3 is working fine . > > > > > > Scenerio-2: > > > =========== > > > > > > > Endpoint-1 > > > > > > / > > > PSTN --> Quintum --> GnuGK --> > > > \ > > > > > > > EndPoint-2 > > > > > > From PSTN to Endpoint-1 or Endpoint-2 direct calling working fine . > > > But when I am trying to transfer (which call was from PSTN) from > > > Endpoint-1 to EndPoint-2 is failing . > > > > > > How can I transfer from PSTN to EndPoint-1's call to EndPoint-2 ? Pls help > > > me . > > > > > > > > > Regards .. > > > > > > Thanks in advanced . > > > > > > > > > ..Tusar.. > > > > > > > > _______________________________________________________ > > > > List: Openh323gk-users@xxxxxxxxxxxxxxxxxxxxx > > Archive: http://sourceforge.net/mailarchive/forum.php?forum_id=8549 > > Homepage: http://www.gnugk.org/ > > > > > ------------------------------------------------------- > The SF.Net email is sponsored by: Beat the post-holiday blues > Get a FREE limited edition SourceForge.net t-shirt from ThinkGeek. > It's fun and FREE -- well, almost....http://www.thinkgeek.com/sfshirt > > _______________________________________________________ > > List: Openh323gk-users@xxxxxxxxxxxxxxxxxxxxx > Archive: http://sourceforge.net/mailarchive/forum.php?forum_id=8549 > Homepage: http://www.gnugk.org/ ------------------------------------------------------- The SF.Net email is sponsored by: Beat the post-holiday blues Get a FREE limited edition SourceForge.net t-shirt from ThinkGeek. It's fun and FREE -- well, almost....http://www.thinkgeek.com/sfshirt _______________________________________________________ List: Openh323gk-users@xxxxxxxxxxxxxxxxxxxxx Archive: http://sourceforge.net/mailarchive/forum.php?forum_id=8549 Homepage: http://www.gnugk.org/
