----- Original Message -----
Sent: Tuesday, January 04, 2005 4:21
PM
Subject: Re: connect
H.323 endpoints to PSTN phones
The Siemens HG-1500 board does support H.323, but
in a very funny way.
You can register the HG module into a H.323
compatible gatekeeper (the HG module acts as an endpoint), but:
1. you can not set the TTL of the
endpoint
2. it does not pay attention to the TTL of the
gatekeeper, the TTL is hardcoded to 60sec.
3. You can register a prefix into the gatekeeper.
Good catch!
4. You can NOT configure a trunk group in the PBX
to send all calls to the HG module and then to the GK.
This was the case with version 2. At the time I
tested this, Siemens mentioned something about a new version, but never had
the chance to see it.
Btw, version 1 was considered as NON-WORKING
:)
----- Original Message -----
Sent: Tuesday, January 04, 2005 5:21
PM
Subject: Re: connect
H.323 endpoints to PSTN phones
Sorry, my first mail had an error, I
meant:
"I want to know the best way to place calls
from H.323 endpoints to PSTN phones using my Siemens
HiPath HG1500 PBX."
The Siemens HiPath HG1500 PBX uses a Siemens
CorNet-IP proprietary protocol, similar to H.323.
I think the HiPath PBX allows the connection to
a Gatekeeper... but I didnt managed to put it to work. Do I need some extra
hardware or software in the middle?? maybe Asterisk will do
it?????
Does someone in the list have a similar
configuration?
Thanks
Joao Pereira
----- Original Message -----
Sent: Tuesday, January 04, 2005 2:56
PM
Subject: Re: connect H.323
endpoints to PSTN phones
> Dear Joao,
> Does Siemens PBX support H.323
gatekeeper feature? If yes, then you did
> need something in the
middle of gatekeeper and SIP Phone, because SIP and
> H.323 are two
totally different protocol.
> Can you tell us more about
your situation?
>
> Yours sincerely,
> Jason Chan
>
----- Original Message -----
> From: "Joao Pereira" <joao.pereira@xxxxxxx>
>
To: <openh323gk-users@xxxxxxxxxxxxxxxxxxxxx>
> Sent: Tuesday, January 04, 2005 8:35
PM
> Subject: connect H.323 endpoints to PSTN
phones
>
>
> > Hi
> > I want to know the
best way to place calls from SIP endpoints to PSTN
> phones
>
> using my Siemens HiPath HG1500 PBX.
> >
> > Is
Asterisk the best solution?? redirecting calls to Asterisk, and then
to
> > the Siemens PBX?
> > Or should I register the
Gatekeeper directly with the Siemens PBX?
> > Does someone have
better ideas?
> > Thanks
> > Joao Pereira
>
>
> >
> >
> >
> >
-------------------------------------------------------
> > The
SF.Net email is sponsored by: Beat the post-holiday blues
> > Get a
FREE limited edition SourceForge.net t-shirt from ThinkGeek.
> >
It's fun and FREE -- well,
almost....http://www.thinkgeek.com/sfshirt
> >
> >
_______________________________________________________
> >
>
> List: Openh323gk-users@xxxxxxxxxxxxxxxxxxxxx
> > Archive: http://sourceforge.net/mailarchive/forum.php?forum_id=8549
> > Homepage: http://www.gnugk.org/
>
>
>
>
>
>
>
-------------------------------------------------------
> The SF.Net
email is sponsored by: Beat the post-holiday blues
> Get a FREE
limited edition SourceForge.net t-shirt from ThinkGeek.
> It's fun and
FREE -- well, almost....http://www.thinkgeek.com/sfshirt
>
>
_______________________________________________________
>
>
List: Openh323gk-users@xxxxxxxxxxxxxxxxxxxxx
> Archive: http://sourceforge.net/mailarchive/forum.php?forum_id=8549
> Homepage: http://www.gnugk.org/
>
