On Thu, Jul 16, 2020 at 09:08:57PM +0530, Sumit Semwal wrote: > The nt36672a panel from Tianma is a FHD+ panel with a resolution of 1080x2246 > and 6.18 inches size. It is found in some of the Poco F1 phones. > > Signed-off-by: Sumit Semwal <sumit.semwal@xxxxxxxxxx> > --- > .../display/panel/tianma,nt36672a.yaml | 110 ++++++++++++++++++ > 1 file changed, 110 insertions(+) > create mode 100644 Documentation/devicetree/bindings/display/panel/tianma,nt36672a.yaml > > diff --git a/Documentation/devicetree/bindings/display/panel/tianma,nt36672a.yaml b/Documentation/devicetree/bindings/display/panel/tianma,nt36672a.yaml > new file mode 100644 > index 000000000000..3c583ca926ee > --- /dev/null > +++ b/Documentation/devicetree/bindings/display/panel/tianma,nt36672a.yaml > @@ -0,0 +1,110 @@ > +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/display/panel/tianma,nt36672a.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Tianma model NT36672A DSI Panel display driver > + > +maintainers: > + - Sumit Semwal <sumit.semwal@xxxxxxxxxx> > + > +description: | > + The nt36672a panel from Tianma is a FHD+ LCD display panel with a resolution > + of 1080x2246. It is a video mode DSI panel. > + > +allOf: > + - $ref: panel-common.yaml# > + > +properties: > + compatible: > + const: tianma,nt36672a > + > + reg: > + description: DSI virtual channel of the peripheral > + > + reset-gpios: > + description: phandle of gpio for reset line - This should be 8mA, gpio > + can be configured using mux, pinctrl, pinctrl-names (active high) > + > + vddio-supply: > + description: phandle of the regulator that provides the supply voltage > + Power IC supply > + > + vddpos-supply: > + description: phandle of the positive boost supply regulator > + > + vddneg-supply: > + description: phandle of the negative boost supply regulator > + > + pinctrl-names: > + description: Pinctrl for panel active and suspend > + > + pinctrl-0: > + description: Active pinctrls > + > + pinctrl-1: > + description: Suspend pinctrls I think the pinctrl should go in the DSI controller node, not the display unless it is settings for 'reset-gpios'. > + > + ports: > + type: object > + properties: > + port@0: > + type: object > + description: DSI input port driven by master DSI > + properties: > + reg: > + const: 0 > + > + required: > + - reg For a single port, you can do just 'port' (without ports node). > + > +required: > + - compatible > + - reg > + - vddi0-supply > + - vddpos-supply > + - vddneg-supply > + - reset-gpios > + - pinctrl-names > + - pinctrl-0 > + - pinctrl-1 > + - ports > + > +unevaluatedProperties: false > + > +examples: > + - |+ > + #include <dt-bindings/gpio/gpio.h> > + dsi0 { dsi { > + #address-cells = <1>; > + #size-cells = <0>; > + > + panel@0 { > + compatible = "tianma,nt36672a"; > + reg = <0>; > + vddi0-supply = <&vreg_l14a_1p88>; > + vddpos-supply = <&lab>; > + vddneg-supply = <&ibb>; > + > + reset-gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>; > + > + pinctrl-names = "panel_active", "panel_suspend"; > + pinctrl-0 = <&sde_dsi_active>; > + pinctrl-1 = <&sde_dsi_suspend>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + tianma_nt36672a_in_0: endpoint { > + remote-endpoint = <&dsi0_out>; > + }; > + }; > + }; > + }; > + }; > + > +... > -- > 2.27.0 > _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
