On Mon, 22 Apr 2024, Rob Herring wrote:
On Sat, Apr 20, 2024 at 09:53:42AM -0500, matthew.gerlach@xxxxxxxxxxxxxxx wrote:
From: Matthew Gerlach <matthew.gerlach@xxxxxxxxxxxxxxx>
Convert the device tree bindings for the Altera Root Port PCIe controller
from text to YAML.
Signed-off-by: Matthew Gerlach <matthew.gerlach@xxxxxxxxxxxxxxx>
---
v4:
- reorder reg-names to match original binding
- move reg and reg-names to top level with limits.
v3:
- Added years to copyright
- Correct order in file of allOf and unevaluatedProperties
- remove items: in compatible field
- fix reg and reg-names constraints
- replace deprecated pci-bus.yaml with pci-host-bridge.yaml
- fix entries in ranges property
- remove device_type from required
v2:
- Move allOf: to bottom of file, just like example-schema is showing
- add constraint for reg and reg-names
- remove unneeded device_type
- drop #address-cells and #size-cells
- change minItems to maxItems for interrupts:
- change msi-parent to just "msi-parent: true"
- cleaned up required:
- make subject consistent with other commits coverting to YAML
- s/overt/onvert/g
---
.../devicetree/bindings/pci/altera-pcie.txt | 50 -----------
.../bindings/pci/altr,pcie-root-port.yaml | 88 +++++++++++++++++++
2 files changed, 88 insertions(+), 50 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/pci/altera-pcie.txt
create mode 100644 Documentation/devicetree/bindings/pci/altr,pcie-root-port.yaml
diff --git a/Documentation/devicetree/bindings/pci/altera-pcie.txt b/Documentation/devicetree/bindings/pci/altera-pcie.txt
deleted file mode 100644
index 816b244a221e..000000000000
--- a/Documentation/devicetree/bindings/pci/altera-pcie.txt
+++ /dev/null
@@ -1,50 +0,0 @@
-* Altera PCIe controller
-
-Required properties:
-- compatible : should contain "altr,pcie-root-port-1.0" or "altr,pcie-root-port-2.0"
-- reg: a list of physical base address and length for TXS and CRA.
- For "altr,pcie-root-port-2.0", additional HIP base address and length.
-- reg-names: must include the following entries:
- "Txs": TX slave port region
- "Cra": Control register access region
- "Hip": Hard IP region (if "altr,pcie-root-port-2.0")
-- interrupts: specifies the interrupt source of the parent interrupt
- controller. The format of the interrupt specifier depends
- on the parent interrupt controller.
-- device_type: must be "pci"
-- #address-cells: set to <3>
-- #size-cells: set to <2>
-- #interrupt-cells: set to <1>
-- ranges: describes the translation of addresses for root ports and
- standard PCI regions.
-- interrupt-map-mask and interrupt-map: standard PCI properties to define the
- mapping of the PCIe interface to interrupt numbers.
-
-Optional properties:
-- msi-parent: Link to the hardware entity that serves as the MSI controller
- for this PCIe controller.
-- bus-range: PCI bus numbers covered
-
-Example
- pcie_0: pcie@c00000000 {
- compatible = "altr,pcie-root-port-1.0";
- reg = <0xc0000000 0x20000000>,
- <0xff220000 0x00004000>;
- reg-names = "Txs", "Cra";
- interrupt-parent = <&hps_0_arm_gic_0>;
- interrupts = <0 40 4>;
- interrupt-controller;
What happened to this? It is clearly needed since the interrupt-map
below points back to this node. Note that that didn't work at one point
in time, but I think we fixed it.
I think the DTs I was using test were created during the point in time
when this did not work. The interrupt-controller boolean and
#interrupt-cells property were in a sub node, and the interrupt-map
pointed to the sub-node. Keeping everything in the base node maintains
compatiblity. I will fix this for v5.
It doesn't seem you are testing the binding against an actual DT.
Please do that.
I need to fix the DTs I'm using for test :)
Thanks for the feedback,
Matthew Gerlach
Rob
- #interrupt-cells = <1>;
- bus-range = <0x0 0xFF>;
- device_type = "pci";
- msi-parent = <&msi_to_gic_gen_0>;
- #address-cells = <3>;
- #size-cells = <2>;
- interrupt-map-mask = <0 0 0 7>;
- interrupt-map = <0 0 0 1 &pcie_0 1>,
- <0 0 0 2 &pcie_0 2>,
- <0 0 0 3 &pcie_0 3>,
- <0 0 0 4 &pcie_0 4>;
- ranges = <0x82000000 0x00000000 0x00000000 0xc0000000 0x00000000 0x10000000
- 0x82000000 0x00000000 0x10000000 0xd0000000 0x00000000 0x10000000>;
- };
