On Fri, Aug 18, 2023 at 01:10:16PM +0200, Josua Mayer wrote:
> Add support for the SolidRun LX2162A System on Module (SoM), and the
> Clearfog evaluation board.
>
> The SoM has few software-controllable features:
> - AR8035 Ethernet PHY
> - eMMC
> - SPI Flash
> - fan controller
> - various eeproms
>
> The Clearfog evaluation board provides:
> - microSD connector
> - USB-A
> - 2x 10Gbps SFP+
> - 2x 25Gbps SFP+ with a retimer
> - 8x 2.5Gbps RJ45
> - 2x mPCI (assembly option / disables 2xRJ45)
>
> The 8x RJ45 ports are connected with an 8-port PHY: Marvell 88E2580
> supporting up to 5Gbps, while SoC and magnetics are limited to 2.5Gbps.
>
> However 2500 speed is untested due to documentation and drivier
> limitations. To avoid confusion the phy nodes have been explicitly
> limited to 1000 for now.
>
> The PCI nodes are disabled, but explicitly added to mark that this board
> can have pci.
> It is expected that the bootloader will patch the status property
> "okay" and disable 2x RJ45 ports, according to active serdes configuration.
>
> Signed-off-by: Josua Mayer <josua@xxxxxxxxxxxxx>
> ---
> V1 -> V2: reordered "compatible" and "reg" properties
> V1 -> V2: replaced chip-specific DT node names with generic ones
> V1 -> V2: removed dead code from fspi node
> V2 -> V3: dropped deprecated address-cells, address-size props from flash node
> V3 -> V4: reordered dt properties such that status is last
> V3 -> V4: changed ethernet-phy on som from /delete-node/ to disabled
>
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> .../dts/freescale/fsl-lx2162a-clearfog.dts | 373 ++++++++++++++++++
> .../dts/freescale/fsl-lx2162a-sr-som.dtsi | 73 ++++
> 3 files changed, 447 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2162a-clearfog.dts
> create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2162a-sr-som.dtsi
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index a750be13ace8..9448d2effd8a 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -34,6 +34,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-honeycomb.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
> dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2162a-qds.dtb
> +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2162a-clearfog.dtb
Out of alphabetical order.
>
> fsl-ls1028a-qds-13bb-dtbs := fsl-ls1028a-qds.dtb fsl-ls1028a-qds-13bb.dtbo
> fsl-ls1028a-qds-65bb-dtbs := fsl-ls1028a-qds.dtb fsl-ls1028a-qds-65bb.dtbo
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2162a-clearfog.dts b/arch/arm64/boot/dts/freescale/fsl-lx2162a-clearfog.dts
> new file mode 100644
> index 000000000000..ad57f4cca62d
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2162a-clearfog.dts
> @@ -0,0 +1,373 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +//
> +// Device Tree file for LX2162A Clearfog
> +//
> +// Copyright 2023 Josua Mayer <josua@xxxxxxxxxxxxx>
> +
> +/dts-v1/;
> +
> +#include "fsl-lx2160a.dtsi"
> +#include "fsl-lx2162a-sr-som.dtsi"
> +
> +/ {
> + model = "SolidRun LX2162A Clearfog";
> + compatible = "solidrun,lx2162a-clearfog", "solidrun,lx2162a-som", "fsl,lx2160a";
> +
> + aliases {
> + crypto = &crypto;
> + i2c0 = &i2c0;
> + i2c1 = &i2c2;
> + i2c2 = &i2c4;
> + i2c3 = &sfp_i2c0;
> + i2c4 = &sfp_i2c1;
> + i2c5 = &sfp_i2c2;
> + i2c6 = &sfp_i2c3;
> + i2c7 = &mpcie1_i2c;
> + i2c8 = &mpcie0_i2c;
> + i2c9 = &pcieclk_i2c;
> + mmc0 = &esdhc0;
> + mmc1 = &esdhc1;
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led_sfp_at: led-sfp-at {
> + gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>; /* PROC_IRQ5 */
> + default-state = "off";
> + };
Have a newline between nodes.
> + led_sfp_ab: led-sfp-ab {
> + gpios = <&gpio2 11 GPIO_ACTIVE_HIGH>; /* PROC_IRQ11 */
> + default-state = "off";
> + };
> + led_sfp_bt: led-sfp-bt {
> + gpios = <&gpio2 13 GPIO_ACTIVE_HIGH>; /* EVT1_B */
> + default-state = "off";
> + };
> + led_sfp_bb: led-sfp-bb {
> + gpios = <&gpio2 14 GPIO_ACTIVE_HIGH>; /* EVT2_B */
> + default-state = "off";
> + };
> + };
> +
> + sfp_at: sfp-at {
> + compatible = "sff,sfp";
> + i2c-bus = <&sfp_i2c0>;
> + mod-def0-gpios = <&gpio2 16 GPIO_ACTIVE_LOW>; /* EVT4_B */
> + maximum-power-milliwatt = <2000>;
> + };
> +
> + sfp_ab: sfp-ab {
> + compatible = "sff,sfp";
> + i2c-bus = <&sfp_i2c1>;
> + mod-def0-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; /* PROC_IRQ1 */
> + maximum-power-milliwatt = <2000>;
> + };
> +
> + sfp_bt: sfp-bt {
> + compatible = "sff,sfp";
> + i2c-bus = <&sfp_i2c2>;
> + mod-def0-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>; /* PROC_IRQ10 */
> + maximum-power-milliwatt = <2000>;
> + };
> +
> + sfp_bb: sfp-bb {
> + compatible = "sff,sfp";
> + i2c-bus = <&sfp_i2c3>;
> + mod-def0-gpios = <&gpio2 15 GPIO_ACTIVE_LOW>; /* EVT3_B */
> + maximum-power-milliwatt = <2000>;
> + };
> +};
> +
> +&i2c2 {
This label node seems out of alphabetical order.
> + status = "okay";
> +
> + /* retimer@18 */
> +
> + i2c-mux@70 {
> + compatible = "nxp,pca9546";
> + reg = <0x70>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + i2c-mux-idle-disconnect;
> +
> + sfp_i2c0: i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + };
> +
> + sfp_i2c1: i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> + };
> +
> + sfp_i2c2: i2c@2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <2>;
> + };
> +
> + sfp_i2c3: i2c@3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <3>;
> + };
> + };
> +
> + i2c-mux@71 {
> + compatible = "nxp,pca9546";
> + reg = <0x71>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + i2c-mux-idle-disconnect;
> +
> + mpcie1_i2c: i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + };
> +
> + mpcie0_i2c: i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> + };
> +
> + pcieclk_i2c: i2c@2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <2>;
> +
> + /* clock-controller@6b */
> + };
> + };
> +};
> +
> +&dpmac3 {
> + sfp = <&sfp_at>;
> + managed = "in-band-status";
> + phys = <&serdes_1 7>;
> +};
> +
> +&dpmac4 {
> + sfp = <&sfp_ab>;
> + managed = "in-band-status";
> + phys = <&serdes_1 6>;
> +};
> +
> +&dpmac5 {
> + sfp = <&sfp_bt>;
> + managed = "in-band-status";
> + phys = <&serdes_1 5>;
> +};
> +
> +&dpmac6 {
> + sfp = <&sfp_bb>;
> + managed = "in-band-status";
> + phys = <&serdes_1 4>;
> +};
> +
> +&dpmac11 {
> + phys = <&serdes_2 0>;
> + phy-handle = <ðernet_phy3>;
> + phy-connection-type = "sgmii";
> + status = "okay";
> +};
> +
> +&dpmac12 {
> + phys = <&serdes_2 1>;
> + phy-handle = <ðernet_phy1>;
> + phy-connection-type = "sgmii";
> + status = "okay";
> +};
> +
> +&dpmac13 {
> + phys = <&serdes_2 6>;
> + phy-handle = <ðernet_phy6>;
> + phy-connection-type = "sgmii";
> + status = "okay";
> +};
> +
> +&dpmac14 {
> + phys = <&serdes_2 7>;
> + phy-handle = <ðernet_phy8>;
> + phy-connection-type = "sgmii";
> + status = "okay";
> +};
> +
> +&dpmac15 {
> + phys = <&serdes_2 4>;
> + phy-handle = <ðernet_phy4>;
> + phy-connection-type = "sgmii";
> + status = "okay";
> +};
> +
> +&dpmac16 {
> + phys = <&serdes_2 5>;
> + phy-handle = <ðernet_phy2>;
> + phy-connection-type = "sgmii";
> + status = "okay";
> +};
> +
> +&dpmac17 {
> + /* override connection to on-SoM phy */
> + /delete-property/ phy-handle;
> + /delete-property/ phy-connection-type;
> +
> + phys = <&serdes_2 2>;
> + phy-handle = <ðernet_phy5>;
> + phy-connection-type = "sgmii";
> + status = "okay";
> +};
> +
> +&dpmac18 {
> + phys = <&serdes_2 3>;
> + phy-handle = <ðernet_phy7>;
> + phy-connection-type = "sgmii";
> + status = "okay";
> +};
> +
> +&emdio1 {
> + ethernet_phy1: ethernet-phy@8 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <8>;
> + max-speed = <1000>;
> + };
> +
> + ethernet_phy2: ethernet-phy@9 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <9>;
> + max-speed = <1000>;
> + };
> +
> + ethernet_phy3: ethernet-phy@10 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <10>;
> + max-speed = <1000>;
> + };
> +
> + ethernet_phy4: ethernet-phy@11 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <11>;
> + max-speed = <1000>;
> + };
> +
> + ethernet_phy5: ethernet-phy@12 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <12>;
> + max-speed = <1000>;
> + };
> +
> + ethernet_phy6: ethernet-phy@13 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <13>;
> + max-speed = <1000>;
> + };
> +
> + ethernet_phy7: ethernet-phy@14 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <14>;
> + max-speed = <1000>;
> + };
> +
> + ethernet_phy8: ethernet-phy@15 {
> + compatible = "ethernet-phy-ieee802.3-c45";
> + reg = <15>;
> + max-speed = <1000>;
> + };
> +};
> +
> +&esdhc0 {
> + sd-uhs-sdr104;
> + sd-uhs-sdr50;
> + sd-uhs-sdr25;
> + sd-uhs-sdr12;
> + status = "okay";
> +};
> +
> +ðernet_phy0 {
> + /*
> + * SoM has a phy at address 1 connected to SoC Ethernet Controller 1.
> + * It competes for WRIOP MAC17, and no connector has been wired.
> + */
> + status = "disabled";
> +};
> +
> +&pcie3 {
> + status = "disabled";
> +};
> +
> +&pcie4 {
> + status = "disabled";
> +};
> +
> +&pcs_mdio3 {
> + status = "okay";
> +};
> +
> +&pcs_mdio4 {
> + status = "okay";
> +};
> +
> +&pcs_mdio5 {
> + status = "okay";
> +};
> +
> +&pcs_mdio6 {
> + status = "okay";
> +};
> +
> +&pcs_mdio11 {
> + status = "okay";
> +};
> +
> +&pcs_mdio12 {
> + status = "okay";
> +};
> +
> +&pcs_mdio13 {
> + status = "okay";
> +};
> +
> +&pcs_mdio14 {
> + status = "okay";
> +};
> +
> +&pcs_mdio15 {
> + status = "okay";
> +};
> +
> +&pcs_mdio16 {
> + status = "okay";
> +};
> +
> +&pcs_mdio17 {
> + status = "okay";
> +};
> +
> +&pcs_mdio18 {
> + status = "okay";
> +};
> +
> +&serdes_1 {
> + status = "okay";
> +};
> +
> +&serdes_2 {
> + status = "okay";
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&usb0 {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2162a-sr-som.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2162a-sr-som.dtsi
> new file mode 100644
> index 000000000000..ac3f9bc60265
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2162a-sr-som.dtsi
> @@ -0,0 +1,73 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +//
> +// Device Tree file for LX2162A-SOM
> +//
> +// Copyright 2021 Rabeeh Khoury <rabeeh@xxxxxxxxxxxxx>
> +// Copyright 2023 Josua Mayer <josua@xxxxxxxxxxxxx>
> +
> +&crypto {
> + status = "okay";
> +};
> +
> +&dpmac17 {
> + phy-handle = <ðernet_phy0>;
> + phy-connection-type = "rgmii-id";
> +};
> +
> +&emdio1 {
> + status = "okay";
> +
> + ethernet_phy0: ethernet-phy@1 {
> + reg = <1>;
> + };
> +};
> +
> +&esdhc1 {
> + status = "okay";
> + bus-width = <8>;
> + mmc-hs200-1_8v;
> + mmc-hs400-1_8v;
We usually have 'status' be the last property.
Shawn
> +};
> +
> +&fspi {
> + status = "okay";
> +
> + flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + m25p,fast-read;
> + spi-max-frequency = <50000000>;
> + /* The following setting enables 1-1-8 (CMD-ADDR-DATA) mode */
> + spi-rx-bus-width = <8>;
> + spi-tx-bus-width = <1>;
> + };
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + fan-controller@18 {
> + compatible = "ti,amc6821";
> + reg = <0x18>;
> + };
> +
> + ddr_spd: eeprom@51 {
> + compatible = "st,24c02", "atmel,24c02";
> + reg = <0x51>;
> + read-only;
> + };
> +
> + config_eeprom: eeprom@57 {
> + compatible = "st,24c02", "atmel,24c02";
> + reg = <0x57>;
> + };
> +};
> +
> +&i2c4 {
> + status = "okay";
> +
> + variable_eeprom: eeprom@54 {
> + compatible = "st,24c2048", "atmel,24c2048";
> + reg = <0x54>;
> + };
> +};
> --
> 2.35.3
>
