Re: [PATCH 1/2] media: dt-bindings: Add binding doc for i.MX93 MIPI CSI-2

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Jul 05, 2023 at 01:36:46AM +0000, G.N. Zhou (OSS) wrote:
> Hi Alexander,
> 
> Thanks for you comment.
> 
> > -----Original Message-----
> > From: Alexander Stein <alexander.stein@xxxxxxxxxxxxxxx>
> > Sent: 2023年7月4日 16:39
> > To: linux-media@xxxxxxxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx; dl-linux-imx
> > <linux-imx@xxxxxxx>; G.N. Zhou (OSS) <guoniu.zhou@xxxxxxxxxxx>
> > Cc: mchehab@xxxxxxxxxx; laurent.pinchart@xxxxxxxxxxxxxxxx;
> > robh+dt@xxxxxxxxxx; krzysztof.kozlowski+dt@xxxxxxxxxx; conor+dt@xxxxxxxxxx;
> > jacopo.mondi@xxxxxxxxxxxxxxxx
> > Subject: Re: [PATCH 1/2] media: dt-bindings: Add binding doc for i.MX93 MIPI
> > CSI-2
> > 
> > Hi Guoniu,
> > 
> > thanks for posting this driver.
> > 
> > Am Montag, 3. Juli 2023, 13:37:33 CEST schrieb guoniu.zhou@xxxxxxxxxxx:
> > >
> > > From: "Guoniu.zhou" <guoniu.zhou@xxxxxxx>
> > >
> > > Add new binding documentation for DesignWare Core MIPI CSI-2 receiver
> > > and DPHY found on NXP i.MX93.
> > >
> > > Signed-off-by: Guoniu.zhou <guoniu.zhou@xxxxxxx>
> > > ---
> > >  .../bindings/media/nxp,dwc-mipi-csi2.yaml     | 140 ++++++++++++++++++
> > >  1 file changed, 140 insertions(+)
> > >
> > > diff --git
> > > a/Documentation/devicetree/bindings/media/nxp,dwc-mipi-csi2.yaml
> > > b/Documentation/devicetree/bindings/media/nxp,dwc-mipi-csi2.yaml new
> > > file mode 100644 index 000000000000..ece6fb8991d4
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/media/nxp,dwc-mipi-csi2.yaml
> > > @@ -0,0 +1,140 @@
> > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2
> > > +---
> > > +$id: http://devicetree.org/schemas/media/nxp,dwc-mipi-csi2.yaml#
> > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > +
> > > +title: NXP i.MX93 MIPI CSI-2 Host Controller receiver
> > > +
> > > +maintainers:
> > > +  - G.N. Zhou <guoniu.zhou@xxxxxxx>
> > > +
> > > +description: |-
> > > +  The MIPI CSI-2 receiver found on i.MX93 originates from Synopsys
> > > +  DesignWare Core and it implements the CSI-2 protocol on the host
> > > +  side and a DPHY configured as a Slave acts as the physical layer.
> > > +  Two data lanes are supported on i.MX93 family devices and the data
> > > +  rate of each lane support up to 1.5Gbps.
> > > +
> > > +  While the CSI-2 receiver is separate from the MIPI D-PHY IP core,
> > > + the PHY is completely wrapped by the CSI-2 controller and expose  a
> > > + control interface which only can communicate with CSI-2 controller
> > > + This binding thus covers both IP cores.
> > > +
> > > +properties:
> > > +  compatible:
> > > +    enum:
> > > +      - fsl,imx93-mipi-csi2
> > > +
> > > +  reg:
> > > +    maxItems: 1
> > > +
> > > +  interrupts:
> > > +    maxItems: 1
> > > +
> > > +  clocks:
> > > +    items:
> > > +      - description: The peripheral clock (a.k.a. APB clock)
> > > +      - description: The pixel clock
> > > +      - description: The MIPI D-PHY clock
> > > +
> > > +  clock-names:
> > > +    items:
> > > +      - const: per
> > > +      - const: pixel
> > > +      - const: phy_cfg
> > > +
> > > +  power-domains:
> > > +    maxItems: 1
> > > +
> > > +  ports:
> > > +    $ref: /schemas/graph.yaml#/properties/ports
> > > +
> > > +    properties:
> > > +      port@0:
> > > +        $ref: /schemas/graph.yaml#/$defs/port-base
> > > +        unevaluatedProperties: false
> > > +        description:
> > > +          Input port node, single endpoint describing the CSI-2 transmitter.
> > > +
> > > +        properties:
> > > +          endpoint:
> > > +            $ref: video-interfaces.yaml#
> > > +            unevaluatedProperties: false
> > > +
> > > +            properties:
> > > +              data-lanes:
> > > +                minItems: 1
> > > +                items:
> > > +                  - const: 1
> > > +                  - const: 2
> > > +
> > > +              fsl,hsfreqrange:
> > > +                $ref: /schemas/types.yaml#/definitions/uint32
> > > +                description:
> > > +                  Used to select the desired high speed frequency range
> > > +                  according to data lane bit rate. Please refer to i.MX93
> > > +                  reference manual MIPI CSI-2 DPHY chapter to get a valid
> > > +                  value.
> > 
> > If this is data lane bit rate specific, shouldn't it be set in s_stream callback or
> > similar?
> 
> That's correct if we have a formula to calculate it and get data rate from sensor. But Synopsys only
> provide a table to search the valid hsfreqrange according to data rate and the values are nonlinear
> so I export a property to handle this issue.

We have multiple drivers in mainline that do the same, so it's not a
problem, you can have a table of values in the driver and search for the
right entry at runtime. See
drivers/media/platform/renesas/rcar-vin/rcar-csi2.c for instance.

> > > +
> > > +            required:
> > > +              - data-lanes
> > > +              - fsl,hsfreqrange
> > > +
> > > +      port@1:
> > > +        $ref: /schemas/graph.yaml#/properties/port
> > > +        description:
> > > +          Output port node
> > > +
> > > +required:
> > > +  - compatible
> > > +  - reg
> > > +  - interrupts
> > > +  - clocks
> > > +  - clock-names
> > > +  - power-domains
> > > +  - ports
> > > +
> > > +additionalProperties: false
> > > +
> > > +examples:
> > > +  - |
> > > +    #include <dt-bindings/clock/imx93-clock.h>
> > > +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> > > +    #include <dt-bindings/interrupt-controller/irq.h>
> > > +    #include <dt-bindings/power/fsl,imx93-power.h>
> > > +
> > > +    mipi-csi@4ae00000 {
> > > +        compatible = "fsl,imx93-mipi-csi2";
> > > +        reg = <0x4ae00000 0x10000>;
> > > +        interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
> > > +        clocks = <&clks IMX93_CLK_MIPI_CSI_GATE>,
> > > +                 <&clks IMX93_CLK_CAM_PIX>,
> > > +                 <&clks IMX93_CLK_MIPI_PHY_CFG>;
> > > +        clock-names = "per", "pixel", "phy_cfg";
> > > +        power-domains = <&media_blk_ctrl IMX93_MEDIABLK_PD_MIPI_CSI>;
> > > +
> > > +        ports {
> > > +            #address-cells = <1>;
> > > +            #size-cells = <0>;
> > > +
> > > +            port@0 {
> > > +                reg = <0>;
> > > +
> > > +                mipi_from_sensor: endpoint {
> > > +                    remote-endpoint = <&ap1302_to_mipi>;
> > > +                    data-lanes = <1 2>;
> > > +                    fsl,hsfreqrange = <0x2c>;
> > > +                };
> > > +            };
> > > +
> > > +            port@1 {
> > > +                reg = <1>;
> > > +
> > > +                mipi_to_isi: endpoint {
> > > +                    remote-endpoint = <&isi_in>;
> > > +                };
> > > +            };
> > > +        };
> > > +    };
> > > +...

-- 
Regards,

Laurent Pinchart



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux