From: "Guoniu.zhou" <guoniu.zhou@xxxxxxx> Add new binding documentation for DesignWare Core MIPI CSI-2 receiver and DPHY found on NXP i.MX93. Signed-off-by: Guoniu.zhou <guoniu.zhou@xxxxxxx> --- .../bindings/media/nxp,dwc-mipi-csi2.yaml | 140 ++++++++++++++++++ 1 file changed, 140 insertions(+) diff --git a/Documentation/devicetree/bindings/media/nxp,dwc-mipi-csi2.yaml b/Documentation/devicetree/bindings/media/nxp,dwc-mipi-csi2.yaml new file mode 100644 index 000000000000..ece6fb8991d4 --- /dev/null +++ b/Documentation/devicetree/bindings/media/nxp,dwc-mipi-csi2.yaml @@ -0,0 +1,140 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/nxp,dwc-mipi-csi2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP i.MX93 MIPI CSI-2 Host Controller receiver + +maintainers: + - G.N. Zhou <guoniu.zhou@xxxxxxx> + +description: |- + The MIPI CSI-2 receiver found on i.MX93 originates from Synopsys + DesignWare Core and it implements the CSI-2 protocol on the host + side and a DPHY configured as a Slave acts as the physical layer. + Two data lanes are supported on i.MX93 family devices and the data + rate of each lane support up to 1.5Gbps. + + While the CSI-2 receiver is separate from the MIPI D-PHY IP core, + the PHY is completely wrapped by the CSI-2 controller and expose + a control interface which only can communicate with CSI-2 controller + This binding thus covers both IP cores. + +properties: + compatible: + enum: + - fsl,imx93-mipi-csi2 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: The peripheral clock (a.k.a. APB clock) + - description: The pixel clock + - description: The MIPI D-PHY clock + + clock-names: + items: + - const: per + - const: pixel + - const: phy_cfg + + power-domains: + maxItems: 1 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: + Input port node, single endpoint describing the CSI-2 transmitter. + + properties: + endpoint: + $ref: video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + minItems: 1 + items: + - const: 1 + - const: 2 + + fsl,hsfreqrange: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Used to select the desired high speed frequency range + according to data lane bit rate. Please refer to i.MX93 + reference manual MIPI CSI-2 DPHY chapter to get a valid + value. + + required: + - data-lanes + - fsl,hsfreqrange + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + Output port node + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - power-domains + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/imx93-clock.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/power/fsl,imx93-power.h> + + mipi-csi@4ae00000 { + compatible = "fsl,imx93-mipi-csi2"; + reg = <0x4ae00000 0x10000>; + interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX93_CLK_MIPI_CSI_GATE>, + <&clks IMX93_CLK_CAM_PIX>, + <&clks IMX93_CLK_MIPI_PHY_CFG>; + clock-names = "per", "pixel", "phy_cfg"; + power-domains = <&media_blk_ctrl IMX93_MEDIABLK_PD_MIPI_CSI>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + mipi_from_sensor: endpoint { + remote-endpoint = <&ap1302_to_mipi>; + data-lanes = <1 2>; + fsl,hsfreqrange = <0x2c>; + }; + }; + + port@1 { + reg = <1>; + + mipi_to_isi: endpoint { + remote-endpoint = <&isi_in>; + }; + }; + }; + }; +... -- 2.37.1
