Re: [PATCH 1/2] media: dt-bindings: Add binding doc for i.MX93 MIPI CSI-2

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Guoniu,

thanks for posting this driver.

Am Montag, 3. Juli 2023, 13:37:33 CEST schrieb guoniu.zhou@xxxxxxxxxxx:
> ********************
> Achtung externe E-Mail: Öffnen Sie Anhänge und Links nur, wenn Sie wissen,
> dass diese aus einer sicheren Quelle stammen und sicher sind. Leiten Sie
> die E-Mail im Zweifelsfall zur Prüfung an den IT-Helpdesk weiter.
> Attention external email: Open attachments and links only if you know that
> they are from a secure source and are safe. In doubt forward the email to
> the IT-Helpdesk to check it. ********************
> 
> From: "Guoniu.zhou" <guoniu.zhou@xxxxxxx>
> 
> Add new binding documentation for DesignWare Core MIPI CSI-2 receiver
> and DPHY found on NXP i.MX93.
> 
> Signed-off-by: Guoniu.zhou <guoniu.zhou@xxxxxxx>
> ---
>  .../bindings/media/nxp,dwc-mipi-csi2.yaml     | 140 ++++++++++++++++++
>  1 file changed, 140 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/media/nxp,dwc-mipi-csi2.yaml
> b/Documentation/devicetree/bindings/media/nxp,dwc-mipi-csi2.yaml new file
> mode 100644
> index 000000000000..ece6fb8991d4
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/nxp,dwc-mipi-csi2.yaml
> @@ -0,0 +1,140 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/media/nxp,dwc-mipi-csi2.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: NXP i.MX93 MIPI CSI-2 Host Controller receiver
> +
> +maintainers:
> +  - G.N. Zhou <guoniu.zhou@xxxxxxx>
> +
> +description: |-
> +  The MIPI CSI-2 receiver found on i.MX93 originates from Synopsys
> +  DesignWare Core and it implements the CSI-2 protocol on the host
> +  side and a DPHY configured as a Slave acts as the physical layer.
> +  Two data lanes are supported on i.MX93 family devices and the data
> +  rate of each lane support up to 1.5Gbps.
> +
> +  While the CSI-2 receiver is separate from the MIPI D-PHY IP core,
> +  the PHY is completely wrapped by the CSI-2 controller and expose
> +  a control interface which only can communicate with CSI-2 controller
> +  This binding thus covers both IP cores.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - fsl,imx93-mipi-csi2
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  clocks:
> +    items:
> +      - description: The peripheral clock (a.k.a. APB clock)
> +      - description: The pixel clock
> +      - description: The MIPI D-PHY clock
> +
> +  clock-names:
> +    items:
> +      - const: per
> +      - const: pixel
> +      - const: phy_cfg
> +
> +  power-domains:
> +    maxItems: 1
> +
> +  ports:
> +    $ref: /schemas/graph.yaml#/properties/ports
> +
> +    properties:
> +      port@0:
> +        $ref: /schemas/graph.yaml#/$defs/port-base
> +        unevaluatedProperties: false
> +        description:
> +          Input port node, single endpoint describing the CSI-2
> transmitter. +
> +        properties:
> +          endpoint:
> +            $ref: video-interfaces.yaml#
> +            unevaluatedProperties: false
> +
> +            properties:
> +              data-lanes:
> +                minItems: 1
> +                items:
> +                  - const: 1
> +                  - const: 2
> +
> +              fsl,hsfreqrange:
> +                $ref: /schemas/types.yaml#/definitions/uint32
> +                description:
> +                  Used to select the desired high speed frequency range
> +                  according to data lane bit rate. Please refer to i.MX93
> +                  reference manual MIPI CSI-2 DPHY chapter to get a valid
> +                  value.

If this is data lane bit rate specific, shouldn't it be set in s_stream 
callback or similar?

Best regards,
Alexander

> +
> +            required:
> +              - data-lanes
> +              - fsl,hsfreqrange
> +
> +      port@1:
> +        $ref: /schemas/graph.yaml#/properties/port
> +        description:
> +          Output port node
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +  - clocks
> +  - clock-names
> +  - power-domains
> +  - ports
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/clock/imx93-clock.h>
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +    #include <dt-bindings/power/fsl,imx93-power.h>
> +
> +    mipi-csi@4ae00000 {
> +        compatible = "fsl,imx93-mipi-csi2";
> +        reg = <0x4ae00000 0x10000>;
> +        interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
> +        clocks = <&clks IMX93_CLK_MIPI_CSI_GATE>,
> +                 <&clks IMX93_CLK_CAM_PIX>,
> +                 <&clks IMX93_CLK_MIPI_PHY_CFG>;
> +        clock-names = "per", "pixel", "phy_cfg";
> +        power-domains = <&media_blk_ctrl IMX93_MEDIABLK_PD_MIPI_CSI>;
> +
> +        ports {
> +            #address-cells = <1>;
> +            #size-cells = <0>;
> +
> +            port@0 {
> +                reg = <0>;
> +
> +                mipi_from_sensor: endpoint {
> +                    remote-endpoint = <&ap1302_to_mipi>;
> +                    data-lanes = <1 2>;
> +                    fsl,hsfreqrange = <0x2c>;
> +                };
> +            };
> +
> +            port@1 {
> +                reg = <1>;
> +
> +                mipi_to_isi: endpoint {
> +                    remote-endpoint = <&isi_in>;
> +                };
> +            };
> +        };
> +    };
> +...


-- 
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht München, HRB 105018
Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
http://www.tq-group.com/






[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux