Re: Aw: Re: Re: Re: Re: Re: [PATCH v3 0/5] arm: dts: mt7623: relocate gmacs, mt7530 switch, and add port@5

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 12/04/2023 19:06, Arınç ÜNAL wrote:
On 12.04.2023 19:53, Frank Wunderlich wrote:
Hi

Gesendet: Mittwoch, 12. April 2023 um 18:21 Uhr
Von: "Arınç ÜNAL" <arinc.unal@xxxxxxxxxx>
thanks, it changes the master when i upgrade iproute to 6.1 (from debian bullseye-backports), but i cannot do any traffic on it after switching to gmac1...

5: wan@eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
      link/ether f2:d2:51:56:cd:3d brd ff:ff:ff:ff:ff:ff
      inet 192.168.0.11/24 scope global wan
         valid_lft forever preferred_lft forever

see no p5-TX/gmac-rx

Did you apply the vlan and flooding fix patches from Richard?

have now applied all patches i've found from richard (which are all rejected):

fe4495bb3cc2 2023-02-12 Fix setting up CPU and User ports to be in the correct mode during setup and when toggling vlan_filtering on a bridge port.  (HEAD -> 6.3-rc) b0641f3e1a69 2023-02-12 Fix Flooding: Disable by default on User ports and Enable on CPU ports cb04b3451524 2023-02-12 Do not add all User ports to the CPU by default. This will break Multi CPU when added a seperate patch. It will be overwritten by .port_enable and since we are forcing output to a port via the Special Tag this is not needed.

and now it seems working and is clear ;)

root@bpi-r2:~# ip l show wan
5: wan@eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000
     link/ether f2:d2:51:56:cd:3d brd ff:ff:ff:ff:ff:ff

iperf3
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.00  sec  1.09 GBytes   940 Mbits/sec    0             sender
[  5]   0.00-10.03  sec  1.09 GBytes   936 Mbits/sec                  receiver


iperf3 -R
[ ID] Interval           Transfer     Bitrate         Retr
[  5]   0.00-10.04  sec  1.09 GBytes   936 Mbits/sec    0             sender
[  5]   0.00-10.00  sec  1.09 GBytes   938 Mbits/sec                  receiver


how do you deal with these patches? do you include them into your mt7530 fixes series? they (and vladimirs preferred cpu-port) need to be applied before these DTS-changes

Dealing with this is the last step on my tasklist. Take a look:

https://arinc9.notion.site/mt7530-c-improvements-bbfdc2ceb958484b9627297b88bc6d4a


I'm a bit lost here. @frank can this be merged now or are there still oustanding issues. It seems to me that not, but just in case...

Regards,
Matthias



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux