Re: [PATCH v4 3/7] dt-bindings: clock: jh7110-syscrg: Add PLL clock inputs

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, May 19, 2023 at 03:59:19PM +0800, Xingyu Wu wrote:
> On 2023/5/12 21:49, Conor Dooley wrote:
> > On Fri, May 12, 2023 at 05:56:16PM +0800, Xingyu Wu wrote:
> >> On 2023/5/12 17:35, Conor Dooley wrote:
> >> > On Fri, May 12, 2023 at 04:07:47PM +0800, Xingyu Wu wrote:
> >> >> On 2023/5/12 14:47, Conor Dooley wrote:
> >> >> > On Fri, May 12, 2023 at 10:20:32AM +0800, Xingyu Wu wrote:
> >> >> >> Add PLL clock inputs from PLL clock generator.
> >> >> >> 
> >> >> >> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
> >> >> >> Signed-off-by: Xingyu Wu <xingyu.wu@xxxxxxxxxxxxxxxx>
> >> >> >> ---
> >> >> >>  .../clock/starfive,jh7110-syscrg.yaml         | 20 +++++++++++++++++--
> >> >> >>  1 file changed, 18 insertions(+), 2 deletions(-)
> >> >> > 
> >> >> > /tmp/tmp.KDlzwQM5ma/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.3b.dtb: clock-controller@13020000: clocks: 'oneOf' conditional failed, one must be fixed:
> >> >> > 	[[19], [20], [21], [22], [23], [24], [25], [26], [27]] is too short
> >> >> > 	From schema: /Documentation/devicetree/bindings/clock/starfive,jh7110-syscrg.yaml
> >> >> > /tmp/tmp.KDlzwQM5ma/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.3b.dtb: clock-controller@13020000: clock-names: 'oneOf' conditional failed, one must be fixed:
> >> >> > 	['osc', 'gmac1_rmii_refin', 'gmac1_rgmii_rxin', 'i2stx_bclk_ext', 'i2stx_lrck_ext', 'i2srx_bclk_ext', 'i2srx_lrck_ext', 'tdm_ext', 'mclk_ext'] is too short
> >> >> > 	'i2stx_bclk_ext' was expected
> >> >> > 	'i2stx_lrck_ext' was expected
> >> >> > 	'i2srx_bclk_ext' was expected
> >> >> > 	'i2srx_lrck_ext' was expected
> >> >> > 	'tdm_ext' was expected
> >> >> > 	'mclk_ext' was expected
> >> >> > 	'pll0_out' was expected
> >> >> > 	From schema: /Documentation/devicetree/bindings/clock/starfive,jh7110-syscrg.yaml
> >> >> > /tmp/tmp.KDlzwQM5ma/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.2a.dtb: clock-controller@13020000: clocks: 'oneOf' conditional failed, one must be fixed:
> >> >> > 	[[19], [20], [21], [22], [23], [24], [25], [26], [27]] is too short
> >> >> > 	From schema: Documentation/devicetree/bindings/clock/starfive,jh7110-syscrg.yaml
> >> >> > /tmp/tmp.KDlzwQM5ma/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.2a.dtb: clock-controller@13020000: clock-names: 'oneOf' conditional failed, one must be fixed:
> >> >> > 	['osc', 'gmac1_rmii_refin', 'gmac1_rgmii_rxin', 'i2stx_bclk_ext', 'i2stx_lrck_ext', 'i2srx_bclk_ext', 'i2srx_lrck_ext', 'tdm_ext', 'mclk_ext'] is too short
> >> >> > 	'i2stx_bclk_ext' was expected
> >> >> > 	'i2stx_lrck_ext' was expected
> >> >> > 	'i2srx_bclk_ext' was expected
> >> >> > 	'i2srx_lrck_ext' was expected
> >> >> > 	'tdm_ext' was expected
> >> >> > 	'mclk_ext' was expected
> >> >> > 	'pll0_out' was expected
> >> >> > 	Documentation/devicetree/bindings/clock/starfive,jh7110-syscrg.yaml
> >> >> > 
> >> >> > This binding change is incompatible with the existing devicetrees for
> >> >> > the visionfive 2.
> >> >> 
> >> >> This looks like less clocks about PLL in SYSCRG node. And I add this in patch 7.
> >> > 
> >> > The existing devicetree is a valid, albeit limited, description of the
> >> > hardware.
> >> > After your changes to the clock driver in this series, but *without* the
> >> > changes to the devicetrees, does the system still function?
> >> > From a quick check of 4/7, it looks like it will not?
> >> 
> >> I just tested it on the board and the system still worked without the changes
> >> about devicetree. But these clocks' rate were 0 because these could not get
> >> the PLL clocks from devicetree.
> > 
> > Hmm, that sounds like an issue to me. If all of the clock rates are
> > computed based off of parents that incorrectly report 0, are we not in
> > for trouble?
> > Should the fixed-factor clocks be retained as a fallback for the sake of
> > compatibility?
> > Emil, Stephen?
> 
> I got your concern. Actually, I can add a check in driver to see if the dts
> has pll clocks and then decide whether to use fixed-factor clocks or pll clocks
> from syscon. But eventually we have to use pll clocks and dts has to add it.
> Then the binding should add it synchronously, right?

IMO, it is okay to change the bindings to only allow the "correct"
representation of the clock tree, but the driver should fall back to the
fixed factor clocks if it detects the old/limited configuration.

Cheers,
Conor.

Attachment: signature.asc
Description: PGP signature


[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux