On 4.02.2023 16:07, Frank Wunderlich wrote:
Hi
Gesendet: Samstag, 04. Februar 2023 um 13:12 Uhr
Von: "Arınç ÜNAL" <arinc.unal@xxxxxxxxxx>
An: "Frank Wunderlich" <frank-w@xxxxxxxxxxxxxxx>
Cc: arinc9.unal@xxxxxxxxx, "Rob Herring" <robh+dt@xxxxxxxxxx>, "Krzysztof Kozlowski" <krzysztof.kozlowski+dt@xxxxxxxxxx>, "Matthias Brugger" <matthias.bgg@xxxxxxxxx>, devicetree@xxxxxxxxxxxxxxx, linux-arm-kernel@xxxxxxxxxxxxxxxxxxx, linux-mediatek@xxxxxxxxxxxxxxxxxxx, linux-kernel@xxxxxxxxxxxxxxx, erkin.bozoglu@xxxxxxxxxx, "Sean Wang" <sean.wang@xxxxxxxxxxxx>, "DENG Qingfang" <dqfext@xxxxxxxxx>
Betreff: Re: Aw: Re: [PATCH v2 4/5] arm: dts: mt7623: mux phy0 on Bananapi BPI-R2
On 4.02.2023 14:43, Frank Wunderlich wrote:
Gesendet: Samstag, 04. Februar 2023 um 11:27 Uhr
Von: "Frank Wunderlich" <frank-w@xxxxxxxxxxxxxxx>
An: "Arınç ÜNAL" <arinc.unal@xxxxxxxxxx>
Cc: arinc9.unal@xxxxxxxxx, "Rob Herring" <robh+dt@xxxxxxxxxx>, "Krzysztof Kozlowski" <krzysztof.kozlowski+dt@xxxxxxxxxx>, "Matthias Brugger" <matthias.bgg@xxxxxxxxx>, devicetree@xxxxxxxxxxxxxxx, linux-arm-kernel@xxxxxxxxxxxxxxxxxxx, linux-mediatek@xxxxxxxxxxxxxxxxxxx, linux-kernel@xxxxxxxxxxxxxxx, erkin.bozoglu@xxxxxxxxxx, "Sean Wang" <sean.wang@xxxxxxxxxxxx>, "DENG Qingfang" <dqfext@xxxxxxxxx>
Betreff: Aw: Re: [PATCH v2 4/5] arm: dts: mt7623: mux phy0 on Bananapi BPI-R2
Hi aranc,
have tested this series, basicly it works, but i get only ~620 Mbits/sec (much more i will need on wan) in tx-mode of r2, rx-mode (iperf3 -c IP -R on r2) gets full 939 Mbits/sec. Both no retransmitts.
tried with my laptop which gets 940Mbit/sec in tx mode too...other end is a R2 with 5.15 connected to lan0 (and eth1+aux enabled, dmesg clean so far...for the "kernel log flooded"-comment).
maybe gmac1 needs to be tweaked a bit (clock-settings)?
can you confirm this with your board?
tested the vlan_aware way with 5.15.80 and got better result
ip link add br0 type bridge vlan_filtering 1
ip l set aux master br0
ip l set wan master br0
bridge vlan add vid 99 dev wan
bridge vlan add vid 99 dev aux
bridge vlan
ip l s eth1 up
ip l s wan up
ip a a 192.168.0.11/24 dev eth1
ip l s br0 up
ip l s aux up
i see traffic on eth1 increasing and iperf3 shows in both directions ~940Mbit/s, no strange mesages in dmesg while testing...where do you see these?
You didn't put eth1 on a bridge. I suggest you read my mails with higher
attention so both of our time is spent efficiently.
sorry if i misseed this detail, but it was not part of the instructions i got from mtk and did not found it in our mail-conversion. why do i need to add the gmac into the bridge??
I was going to say, to put the host(s) connected to the wan port on the
same network as other ports, but using the wan interface for that
instead would work. Cool, we can cross this off the list.
the gmac is connected physically to mt7531 p5, and my vlan_aware bridge bridges this port (aux=p5) with wan,
so i see no need to add eth1 to this bridge too...traffic on wan is tagged with vlan 99 and leaving untagged
on aux which is arriving eth1...
tested vlan-way with 6.2 and felix' Patches to more comparable with your test...and got same result (~625Mbit/s in tx and 940Mbit/s in rx-mode=-R on r2)...so it seems anything between 5.15 and 6.2 reduced gmac1 tx bandwidth.
I don't see an incentive to investigate unless the issue is confirmed on
a daily netdev/net-next.git main tree.
have same result on net-next/main with your series, no additional patches on top except adding my build-script and defconfig.
Finding the cause of reduced network performance is quite a challenging
task. The only person I know that gives this a serious approach is Rafał
Miłecki. There are scripts and things they share on the openwrt-devel
mailing list along with details of their investigation, usually for
Broadcom SoCs.
I'm no good in this so I'm not going to do anything about it. There are
issues with the MediaTek ethernet and MT7530 DSA subdriver that
completely break communication which I want to have them addressed.
Arınç
