On Thu, Aug 28, 2014 at 2:45 PM, Mark Rutland <mark.rutland@xxxxxxx> wrote:
> On Thu, Aug 28, 2014 at 06:34:33AM +0100, Ajay kumar wrote:
>> On Wed, Aug 27, 2014 at 8:31 PM, Mark Rutland <mark.rutland@xxxxxxx> wrote:
>> > On Wed, Aug 27, 2014 at 03:48:27PM +0100, Ajay Kumar wrote:
>> >> Add DT nodes for ptn3460 bridge chip and panel.
>> >> Add backlight enable pin and backlight power supply for pwm-backlight.
>> >> Also add bridge phandle needed by dp to enable display on snow.
>> >>
>> >> Note that, snow doesn't support "chunghwa,claa101wb01" panel,
>> >> but still we choose to reuse the binding since "chunghwa,claa101wb01"
>> >> has similar LCD timings.
>> >
>> > What does it actually have?
>> >
>> > It's fine to have "chunghwa,claa101wb01" as a fallback but we should
>> > have an identifier for the actual display, too.
>> Actual display used is "AUO,B116XTN0", for which no data currently exists
>> in panel file. Instead of adding a new panel_desc for B116XTN0,
>> why not we reuse existing ones? what is the "identifier" you are talking about?
>
> The compatible string.
>
> So in the dts we'd have compatible = "au0,b116xtn0", "chunghwa,claa101wb01";
Sorry, hardware engineer says actual LCD name is "auo,b116xw03".
> That way if we need specific data we can add it later.
I think we can add a new panel_desc for "auo,b116xw03".
Because its actual LCD dimension is 256x144, but "chungwa, claa101wb01" has
LCD dimension 223x125.
What is Thierry's opinion on adding this new LCD?
> What vendor is AU0? Can we add a vendor-prefix in parallel?
its "auo" (already present: AU Optronics Corporation)
Ajay
> Thanks,
> Mark.
>
>>
>> Ajay
>> > Thanks,
>> > Mark.
>> >
>> >> Signed-off-by: Ajay Kumar <ajaykumar.rs@xxxxxxxxxxx>
>> >> ---
>> >> Changes since V1:
>> >> -- Remove "simple-panel" compatible string.
>> >> -- Use GPIO_ACTIVE_HIGH instead of 0.
>> >> -- Change panel node naming from "panel-simple" to "panel".
>> >>
>> >> arch/arm/boot/dts/exynos5250-snow.dts | 41 ++++++++++++++++++---------------
>> >> 1 file changed, 22 insertions(+), 19 deletions(-)
>> >>
>> >> diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
>> >> index f2b8c41..1ac9709 100644
>> >> --- a/arch/arm/boot/dts/exynos5250-snow.dts
>> >> +++ b/arch/arm/boot/dts/exynos5250-snow.dts
>> >> @@ -9,6 +9,7 @@
>> >> */
>> >>
>> >> /dts-v1/;
>> >> +#include <dt-bindings/gpio/gpio.h>
>> >> #include "exynos5250.dtsi"
>> >> #include "exynos5250-cros-common.dtsi"
>> >>
>> >> @@ -181,7 +182,7 @@
>> >> dcdc3 {
>> >> ti,enable-ext-control;
>> >> };
>> >> - fet1 {
>> >> + fet1: fet1 {
>> >> regulator-name = "vcd_led";
>> >> ti,overcurrent-wait = <3>;
>> >> };
>> >> @@ -204,7 +205,7 @@
>> >> regulator-always-on;
>> >> ti,overcurrent-wait = <3>;
>> >> };
>> >> - fet6 {
>> >> + fet6: fet6 {
>> >> regulator-name = "lcd_vdd";
>> >> ti,overcurrent-wait = <3>;
>> >> };
>> >> @@ -253,6 +254,15 @@
>> >> pinctrl-0 = <&max98095_en>;
>> >> pinctrl-names = "default";
>> >> };
>> >> +
>> >> + ptn3460: lvds-bridge@20 {
>> >> + compatible = "nxp,ptn3460";
>> >> + reg = <0x20>;
>> >> + powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>;
>> >> + reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>;
>> >> + edid-emulation = <5>;
>> >> + panel = <&panel>;
>> >> + };
>> >> };
>> >>
>> >> i2s0: i2s@03830000 {
>> >> @@ -300,11 +310,13 @@
>> >> vdd_pll-supply = <&ldo8_reg>;
>> >> };
>> >>
>> >> - backlight {
>> >> + backlight: backlight {
>> >> compatible = "pwm-backlight";
>> >> pwms = <&pwm 0 1000000 0>;
>> >> brightness-levels = <0 100 500 1000 1500 2000 2500 2800>;
>> >> default-brightness-level = <7>;
>> >> + enable-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>;
>> >> + power-supply = <&fet1>;
>> >> pinctrl-0 = <&pwm0_out>;
>> >> pinctrl-names = "default";
>> >> };
>> >> @@ -314,6 +326,12 @@
>> >> samsung,invert-vclk;
>> >> };
>> >>
>> >> + panel: panel {
>> >> + compatible = "chunghwa,claa101wb01";
>> >> + power-supply = <&fet6>;
>> >> + backlight = <&backlight>;
>> >> + };
>> >> +
>> >> dp-controller@145B0000 {
>> >> status = "okay";
>> >> pinctrl-names = "default";
>> >> @@ -325,22 +343,7 @@
>> >> samsung,link-rate = <0x0a>;
>> >> samsung,lane-count = <2>;
>> >> samsung,hpd-gpio = <&gpx0 7 0>;
>> >> -
>> >> - display-timings {
>> >> - native-mode = <&timing1>;
>> >> -
>> >> - timing1: timing@1 {
>> >> - clock-frequency = <70589280>;
>> >> - hactive = <1366>;
>> >> - vactive = <768>;
>> >> - hfront-porch = <40>;
>> >> - hback-porch = <40>;
>> >> - hsync-len = <32>;
>> >> - vback-porch = <10>;
>> >> - vfront-porch = <12>;
>> >> - vsync-len = <6>;
>> >> - };
>> >> - };
>> >> + bridge = <&ptn3460>;
>> >> };
>> >> };
>> >>
>> >> --
>> >> 1.7.9.5
>> >>
>> >> --
>> >> To unsubscribe from this list: send the line "unsubscribe devicetree" in
>> >> the body of a message to majordomo@xxxxxxxxxxxxxxx
>> >> More majordomo info at http://vger.kernel.org/majordomo-info.html
>> >>
>>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
