On Wed, Aug 27, 2014 at 8:31 PM, Mark Rutland <mark.rutland@xxxxxxx> wrote:
> On Wed, Aug 27, 2014 at 03:48:27PM +0100, Ajay Kumar wrote:
>> Add DT nodes for ptn3460 bridge chip and panel.
>> Add backlight enable pin and backlight power supply for pwm-backlight.
>> Also add bridge phandle needed by dp to enable display on snow.
>>
>> Note that, snow doesn't support "chunghwa,claa101wb01" panel,
>> but still we choose to reuse the binding since "chunghwa,claa101wb01"
>> has similar LCD timings.
>
> What does it actually have?
>
> It's fine to have "chunghwa,claa101wb01" as a fallback but we should
> have an identifier for the actual display, too.
Actual display used is "AUO,B116XTN0", for which no data currently exists
in panel file. Instead of adding a new panel_desc for B116XTN0,
why not we reuse existing ones? what is the "identifier" you are talking about?
Ajay
> Thanks,
> Mark.
>
>> Signed-off-by: Ajay Kumar <ajaykumar.rs@xxxxxxxxxxx>
>> ---
>> Changes since V1:
>> -- Remove "simple-panel" compatible string.
>> -- Use GPIO_ACTIVE_HIGH instead of 0.
>> -- Change panel node naming from "panel-simple" to "panel".
>>
>> arch/arm/boot/dts/exynos5250-snow.dts | 41 ++++++++++++++++++---------------
>> 1 file changed, 22 insertions(+), 19 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
>> index f2b8c41..1ac9709 100644
>> --- a/arch/arm/boot/dts/exynos5250-snow.dts
>> +++ b/arch/arm/boot/dts/exynos5250-snow.dts
>> @@ -9,6 +9,7 @@
>> */
>>
>> /dts-v1/;
>> +#include <dt-bindings/gpio/gpio.h>
>> #include "exynos5250.dtsi"
>> #include "exynos5250-cros-common.dtsi"
>>
>> @@ -181,7 +182,7 @@
>> dcdc3 {
>> ti,enable-ext-control;
>> };
>> - fet1 {
>> + fet1: fet1 {
>> regulator-name = "vcd_led";
>> ti,overcurrent-wait = <3>;
>> };
>> @@ -204,7 +205,7 @@
>> regulator-always-on;
>> ti,overcurrent-wait = <3>;
>> };
>> - fet6 {
>> + fet6: fet6 {
>> regulator-name = "lcd_vdd";
>> ti,overcurrent-wait = <3>;
>> };
>> @@ -253,6 +254,15 @@
>> pinctrl-0 = <&max98095_en>;
>> pinctrl-names = "default";
>> };
>> +
>> + ptn3460: lvds-bridge@20 {
>> + compatible = "nxp,ptn3460";
>> + reg = <0x20>;
>> + powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>;
>> + reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>;
>> + edid-emulation = <5>;
>> + panel = <&panel>;
>> + };
>> };
>>
>> i2s0: i2s@03830000 {
>> @@ -300,11 +310,13 @@
>> vdd_pll-supply = <&ldo8_reg>;
>> };
>>
>> - backlight {
>> + backlight: backlight {
>> compatible = "pwm-backlight";
>> pwms = <&pwm 0 1000000 0>;
>> brightness-levels = <0 100 500 1000 1500 2000 2500 2800>;
>> default-brightness-level = <7>;
>> + enable-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>;
>> + power-supply = <&fet1>;
>> pinctrl-0 = <&pwm0_out>;
>> pinctrl-names = "default";
>> };
>> @@ -314,6 +326,12 @@
>> samsung,invert-vclk;
>> };
>>
>> + panel: panel {
>> + compatible = "chunghwa,claa101wb01";
>> + power-supply = <&fet6>;
>> + backlight = <&backlight>;
>> + };
>> +
>> dp-controller@145B0000 {
>> status = "okay";
>> pinctrl-names = "default";
>> @@ -325,22 +343,7 @@
>> samsung,link-rate = <0x0a>;
>> samsung,lane-count = <2>;
>> samsung,hpd-gpio = <&gpx0 7 0>;
>> -
>> - display-timings {
>> - native-mode = <&timing1>;
>> -
>> - timing1: timing@1 {
>> - clock-frequency = <70589280>;
>> - hactive = <1366>;
>> - vactive = <768>;
>> - hfront-porch = <40>;
>> - hback-porch = <40>;
>> - hsync-len = <32>;
>> - vback-porch = <10>;
>> - vfront-porch = <12>;
>> - vsync-len = <6>;
>> - };
>> - };
>> + bridge = <&ptn3460>;
>> };
>> };
>>
>> --
>> 1.7.9.5
>>
>> --
>> To unsubscribe from this list: send the line "unsubscribe devicetree" in
>> the body of a message to majordomo@xxxxxxxxxxxxxxx
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
